El Sábado, 6 de Enero de 2007 04:03, Octavio Ávalos escribió:
El Sábado, 6 de Enero de 2007 03:46, Carlos E. R. escribió:
El 2007-01-06 a las 03:18 +0100, Octavio Ávalos escribió:
Ya lo instalé desde el principio y en /var/spool/fax/ lamentablemente no tengo el archivo config.ttyS1
Está claro el modem y yo no nos llevamos bien. Se las prometía gordas cuando hice la llamada con el minicom pero en este caso .........
¿Y que es lo que te ha dicho el faxaddmodem?
Lo mismo que la otra vez, te lo voy a poner a ver que te parece
/etc/init.d/hylafax start Starting service HylaFAX done
You do not appear to have any modems configured for use. Modems are configured for use with HylaFAX with the faxaddmodem(8C) command. Do you want to run faxaddmodem to configure a modem [yes]? Serial port that modem is connected to []? ttyS1
Ok, time to setup a configuration file for the modem. The manual page config(5F) may be useful during this process. Also be aware that at any time you can safely interrupt this procedure.
Reading scheduler config file /var/spool/fax/etc/config.
No existing configuration, let's do this from scratch.
Country code [34]? Area code [981]? Phone number of fax modem [+34 981 555-1212]? +34 981 351878 Local identification string (for TSI/CIG) ["NothingSetup"]? Long distance dialing prefix [0]? International dialing prefix [00]? Dial string rules file (relative to /var/spool/fax) [etc/dialrules.europe]? Tracing during normal server operation [527]? Tracing during send and receive sessions [527]? Protection mode for received facsimile [0600]? Protection mode for session logs [0600]? Protection mode for ttyS1 [0600]? Rings to wait before answering [1]? Modem speaker volume [off]? Command line arguments to getty program ["-h %l dx_%s"]? Pathname of TSI access control list file (relative to /var/spool/fax) [""]? Pathname of Caller-ID access control list file (relative to /var/spool/fax) [""]? Tag line font file (relative to /var/spool/fax) [etc/lutRS18.pcf]? Tag line format string ["From %%l|%c|Page %%P of %%T"]? Time before purging a stale UUCP lock file (secs) [30]? Hold UUCP lockfile during inbound data calls [Yes]? Hold UUCP lockfile during inbound voice calls [Yes]? Percent good lines to accept during copy quality checking [95]? Max consecutive bad lines to accept during copy quality checking [5]? Max number of pages to accept in a received facsimile [25]? Syslog facility name for ServerTracing messages [daemon]? Set UID to 0 to manipulate CLOCAL [""]? Use available priority job scheduling mechanism [""]?
The non-default server configuration parameters are:
CountryCode: 34 AreaCode: 981 FAXNumber: +34 981 351878 LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules.europe ServerTracing: 527 SessionTracing: 527 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "NothingSetup" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25
Are these ok [yes]?
Now we are going to probe the tty port to figure out the type of modem that is attached. This takes a few seconds, so be patient. Note that if you do not have the modem cabled to the port, or the modem is turned off, this may hang (just go and cable up the modem or turn it on, or whatever).
Probing for best speed to talk to modem: 38400 19200 9600 4800 2400 1200 Unable to deduce DTE-DCE speed; check that you are using the correct device and/or that your modem is setup properly. If all else fails, try the -s option to lock the speed. Do you want to run faxaddmodem to configure another modem [yes]? no
Done verifying system setup. linux:~ # init q linux:~ # probemodem Serial port that modem is connected to []? ttyS1
Now we are going to probe the tty port. This takes a few seconds, so be patient. Note that if you do not have the modem cabled to the port, or the modem is turned off, this may hang (just go and cable up the modem or turn it on, or whatever).
Probing for best speed to talk to modem: 38400 19200 9600 4800 2400 1200 Unable to deduce DTE-DCE speed; check that you are using the correct device and/or that your modem is setup properly. If all else fails, try the -s option to lock the speed.
Un saludo
Como el archivo inittab no es muy largo lo voy a poner a ver si veis algo extraño: # # /etc/inittab # # Copyright (c) 1996-2002 SuSE Linux AG, Nuernberg, Germany. All rights reserved. # # Author: Florian La Roche, 1996 # Please send feedback to http://www.suse.de/feedback # # This is the main configuration file of /sbin/init, which # is executed by the kernel on startup. It describes what # scripts are used for the different run-levels. # # All scripts for runlevel changes are in /etc/init.d/. # # This file may be modified by SuSEconfig unless CHECK_INITTAB # in /etc/sysconfig/suseconfig is set to "no" # # The default runlevel is defined here id:5:initdefault: # First script to be executed, if not booting in emergency (-b) mode si::bootwait:/etc/init.d/boot # /etc/init.d/rc takes care of runlevel handling # # runlevel 0 is System halt (Do not use this for initdefault!) # runlevel 1 is Single user mode # runlevel 2 is Local multiuser without remote network (e.g. NFS) # runlevel 3 is Full multiuser with network # runlevel 4 is Not used # runlevel 5 is Full multiuser with network and xdm # runlevel 6 is System reboot (Do not use this for initdefault!) # l0:0:wait:/etc/init.d/rc 0 l1:1:wait:/etc/init.d/rc 1 l2:2:wait:/etc/init.d/rc 2 l3:3:wait:/etc/init.d/rc 3 #l4:4:wait:/etc/init.d/rc 4 l5:5:wait:/etc/init.d/rc 5 l6:6:wait:/etc/init.d/rc 6 # what to do in single-user mode ls:S:wait:/etc/init.d/rc S ~~:S:respawn:/sbin/sulogin # what to do when CTRL-ALT-DEL is pressed ca::ctrlaltdel:/sbin/shutdown -r -t 4 now # special keyboard request (Alt-UpArrow) # look into the kbd-0.90 docs for this kb::kbrequest:/bin/echo "Keyboard Request -- edit /etc/inittab to let this work." # what to do when power fails/returns pf::powerwait:/etc/init.d/powerfail start pn::powerfailnow:/etc/init.d/powerfail now #pn::powerfail:/etc/init.d/powerfail now po::powerokwait:/etc/init.d/powerfail stop # for ARGO UPS sh:12345:powerfail:/sbin/shutdown -h now THE POWER IS FAILING # getty-programs for the normal runlevels # <id>:<runlevels>:<action>:<process> # The "id" field MUST be the same as the last # characters of the device (after "tty"). 1:2345:respawn:/sbin/mingetty --noclear tty1 2:2345:respawn:/sbin/mingetty tty2 3:2345:respawn:/sbin/mingetty tty3 4:2345:respawn:/sbin/mingetty tty4 5:2345:respawn:/sbin/mingetty tty5 6:2345:respawn:/sbin/mingetty tty6 # #S0:12345:respawn:/sbin/agetty -L 9600 ttyS0 vt102 #cons:1235:respawn:/sbin/smart_agetty -L 38400 console # # Note: Do not use tty7 in runlevel 3, this virtual line # is occupied by the programm xdm. # # This is for the package xdmsc, after installing and # and configuration you should remove the comment character # from the following line: #7:3:respawn:+/etc/init.d/rx tty7 # modem getty. # mo:235:respawn:/usr/sbin/mgetty -s 38400 modem # fax getty (hylafax) mo:35:respawn:/usr/lib/fax/faxgetty /dev/ttyS1 # activar con "init q" # vbox (voice box) getty # I6:35:respawn:/usr/sbin/vboxgetty -d /dev/ttyI6 # I7:35:respawn:/usr/sbin/vboxgetty -d /dev/ttyI7 # end of /etc/inittab -- Octavio Ávalos --------------------------------------------------------------------- Para dar de baja la suscripción, mande un mensaje a: opensuse-es+unsubscribe@opensuse.org Para obtener el resto de direcciones-comando, mande un mensaje a: opensuse-es+help@opensuse.org