Am Sonntag, 7. Februar 2010 12:14:02 schrieben Sie:
Am Sonntag, 7. Februar 2010 12:05:53 schrieben Sie:
Am Samstag, 6. Februar 2010 17:38:34 schrieb Heinz Diehl:
On 06.02.2010, Thomas Moritz wrote:
Meine WD-Book-Platte hatte ich nach 2-monatigem Einsatz reklamiert, die sie fortlaufende klickende Geraeusche machte.
hdparm -B 255 /dev/xxx
Das ist kein Kernel-Problem, soweit ich weiss, sondern haengt mit diversen Strosparmechanismen zusammen.
Nun war die neue 1.5 TB HD etwa 1 Tag in Betrieb und ich fürchte so hält sie das nicht lange durch:
In 31h 644 load cycles, da ist die HD in etwa 1 1/2 Jahren hinüber, da der Hersteller 300000 angibt.
Device Model: WDC WD15EARS-00Z5B1 Firmware Version: 80.00A80
# hdparm -B 127 /dev/sdc
/dev/sdc: setting Advanced Power Management level to 0x7f (127) HDIO_DRIVE_CMD failed: Input/output error
# hdparm -B 255 /dev/sdc
/dev/sdc: setting Advanced Power Management level to disabled HDIO_DRIVE_CMD failed: Input/output error
Was nun?
hdparm -i /dev/sdc /dev/sdc: Model=WDC WD15EARS-00Z5B1 , FwRev=80.00A80, SerialNo= Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50 BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=?16? CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=18446744072344861488 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 AdvancedPM=no WriteCache=enabled Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7 Komisch für eine aktuelle HD, die sich Caviar _Green_ nennt: AdvancedPM=no Und das dürfte der Grund sein, warum "hdparm -B" nicht funktioniert. Vielleicht hilft das: -S Set the standby (spindown) timeout for the drive. This value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values. hdparm -S 0 /dev/sdc Mal schauen, ob sich was tut: 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 34 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 5 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 655 Mittlerweile war die HD nur angehängt und es hat sich der Wert in 2h von 644 auf 655 erhöht. Al -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org