Re: SuSE 9.2 erkennt keine ATA-IDE an Promise Kontroller

Am Mittwoch, 23. Februar 2005 23:23 schrieb Michael Weyand:

Hallo Liste,

SuSE 9.2 erkennt meine Samsung ATA-100 IDE Platte nicht am Promise SATA Kontroller (PDC20378), obwohl im BIOS die Platte korrekt erkannt wird. Ich fahe den Rechner im IDE und nicht im RAID Mode. Sata_promise Modul wird beim Kontrollercheck in Yast auch gefunden und ist auch in mkinitrd eingetragen. Also ich habe hier mehrere TX2/4 irgendwas, da geht auch kein PATA...liegt nicht an Suse sondern am 2.6.x Kerneltreiber, der den PATA Teil nicht unterstützt. Hotplug geht auch nicht an SATA. Unter Win*o** Treibern geht alles...

G. Roland

MoBo: Asus A8V CPU: AMD64 3200 SCSI: Dawicontrol DC2679-UW

HDD/Atapi: 2 IDE ATA-100 am VIA Kontroller DVD PLextor am VIA Kontroller Asus CD-ROM am VIA Kontroller 1 SCSI-UW am SCSI Kontroller (werden alle erkannt und laufen)

Ich hab alle möglichen Kombination in der Bootreihenfolge ausprobiert. Keine Änderung Hier kommt mein dmesg. Jedewede Hilfe/Kommentare sehr willkommen. Gruss Michael

------------------

Bootdata ok (command line is root=/dev/sda2 vga=0x31a selinux=0 console=tty0 resume=/dev/sda1 desktop elevator=as splash=silent) Linux version 2.6.8-24.10-default (geeko@buildhost) (gcc version 3.3.4 (pre 3.3.5 20040809)) #1 Wed Dec 22 11:54:27 UTC 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable) BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data) BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS) BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) No mptable found. On node 0 totalpages: 262064 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 257968 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa810 ACPI: XSDT (v001 A M I OEMXSDT 0x10000427 MSFT 0x00000097) @ 0x000000003ffb0100 ACPI: FADT (v003 A M I OEMFACP 0x10000427 MSFT 0x00000097) @ 0x000000003ffb0290 ACPI: MADT (v001 A M I OEMAPIC 0x10000427 MSFT 0x00000097) @ 0x000000003ffb0390 ACPI: OEMB (v001 A M I OEMBIOS 0x10000427 MSFT 0x00000097) @ 0x000000003ffc0040 ACPI: DSDT (v001 A0036 A0036001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information Checking aperture... CPU 0: aperture @ e0000000 size 256 MB Built 1 zonelists Kernel command line: root=/dev/sda2 vga=0x31a selinux=0 console=tty0 resume=/dev/sda1 desktop elevator=as splash=silent bootsplash: silent mode. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 2002.646 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 1023768k/1048256k available (2325k kernel code, 23708k reserved, 927k data, 180k init) Calibrating delay loop... 3923.96 BogoMIPS (lpj=1961984) Security Scaffold v1.0.0 initialized SELinux: Disabled at boot. Mount-cache hash table entries: 256 (order: 0, 4096 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00 ACPI: Looking for DSDT in initrd... not found! Using local APIC NMI watchdog using perfctr0 Using local APIC timer interrupts. Detected 12.516 MHz APIC timer. checking if image is initramfs...it isn't (no cpio magic); looks like an initrd NET: Registered protocol family 16 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040715 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. PCI: Using ACPI for IRQ routing ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 217 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca) agpgart: Detected AGP bridge 0 agpgart: Maximum main memory to use for agp memory: 941M agpgart: AGP aperture is 256M @ 0xe0000000 PCI-DMA: Disabling IOMMU. IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1109197912.341:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1 PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1 PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 1 PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 1 vesafb: framebuffer at 0xf0000000, mapped to 0xffffff0000180000, using 10240k, total 32768k vesafb: mode is 1280x1024x16, linelength=2560, pages=1 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 47601 bytes,<6>...found (1280x1024, 24984 bytes, v3). Console: switching to colour frame buffer device 158x57 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.100 (c) Dave Jones serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 201 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive hdb: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: ST3120022A, ATA DISK drive hdd: IBM-DTLA-307045, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... ide2: Wait for ready failed before probe ! Probing IDE interface ide3... ide3: Wait for ready failed before probe ! Probing IDE interface ide4... ide4: Wait for ready failed before probe ! Probing IDE interface ide5... ide5: Wait for ready failed before probe ! hdc: max request size: 1024KiB hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 hdd: max request size: 128KiB hdd: 90069840 sectors (46115 MB) w/1916KiB Cache, CHS=65535/16/63, UDMA(100) hdd: cache flushes not supported hdd: hdd1 hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache Uniform CD-ROM driver Revision: 3.20 hdb: ATAPI 50X CD-ROM drive, 128kB Cache ide-floppy driver 0.99.newide mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 alps.c: E6 report: 56 03 3c input: PS2++ Logitech Wheel Mouse on isa0060/serio1 input: PC Speaker md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET: Registered protocol family 1 PM: Reading pmdisk image. swsusp: Resume From Partition: /dev/sda1 pmdisk: Error -6 resuming PM: Resume from disk failed. ACPI: (supports S0 S1 S3 S4 S5) ACPI wakeup devices: PCI0 PS2K PS2M UAR2 UAR1 AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). SCSI subsystem initialized libata version 1.02 loaded. sata_promise version 1.00 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177 ata1: SATA max UDMA/133 cmd 0xFFFFFF0000006200 ctl 0xFFFFFF0000006238 bmdma 0x0 irq 177 ata2: SATA max UDMA/133 cmd 0xFFFFFF0000006280 ctl 0xFFFFFF00000062B8 bmdma 0x0 irq 177 ata1: no device found (phy stat 00000000) scsi0 : sata_promise ata2: no device found (phy stat 00000000) scsi1 : sata_promise ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 185 sym0: <875> rev 0x26 at pci 0000:00:0c.0 irq 185 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: SCSI BUS has been reset. scsi2 : sym-2.1.18j Vendor: IBM Model: DDRS-39130W Rev: S97B Type: Direct-Access ANSI SCSI revision: 02 sym0:3:0: tagged command queuing enabled, command queue depth 16. scsi(2:0:3:0): Beginning Domain Validation sym0:3: wide asynchronous. sym0:3: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15) scsi(2:0:3:0): Domain Validation skipping write tests scsi(2:0:3:0): Ending Domain Validation SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 Attached scsi disk sda at scsi2, channel 0, id 3, lun 0 Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7270 Type: Sequential-Access ANSI SCSI revision: 02 scsi(2:0:4:0): Beginning Domain Validation sym0:4: FAST-10 SCSI 7.8 MB/s ST (128.0 ns, offset 15) scsi(2:0:4:0): Domain Validation skipping write tests scsi(2:0:4:0): Ending Domain Validation Vendor: IOMEGA Model: ZIP 100 Rev: J.02 Type: Direct-Access ANSI SCSI revision: 02 scsi(2:0:6:0): Beginning Domain Validation scsi(2:0:6:0): Ending Domain Validation Attached scsi removable disk sdb at scsi2, channel 0, id 6, lun 0 ReiserFS: sda2: found reiserfs format "3.6" with standard journal ReiserFS: sda2: using ordered data mode reiserfs: using flush barriers ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda2: checking transaction log (sda2) reiserfs: disabling flush barriers on sda2 ReiserFS: sda2: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Trying to move old root to /initrd ... failed Unmounting old root Trying to free ramdisk memory ... failed Freeing unused kernel memory: 180k freed Adding 1028072k swap on /dev/sda1. Priority:42 extents:1 8139too Fast Ethernet driver 0.9.27 ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 193 eth0: RealTek RTL8139 at 0xffffff0000066000, 00:50:fc:ca:86:55, IRQ 193 eth0: Identified 8139 chip type 'RTL-8100B/8139D' usbcore: registered new driver usbfs usbcore: registered new driver hub md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com evdev_connect: evdev 0000010037ff4400 handle 0000010037ff4420 name event0 evdev_connect: evdev 0000010037ff4200 handle 0000010037ff4220 name event1 evdev_connect: evdev 000001003fca8a00 handle 000001003fca8a20 name event2 sata_via version 0.20 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 201 sata_via(0000:00:0f.0): routed to hard irq line 10 ata3: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 201 ata4: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 201 ata3: no device found (phy stat 00000000) scsi3 : sata_via ieee1394: Initialized config rom entry `ip1394' ata4: no device found (phy stat 00000000) scsi4 : sata_via ohci1394: $Rev: 1223 $ Ben Collins ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[169] MMIO=[fa600000-fa6007ff] Max Packet=[2048] USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 209 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: irq 209, io base 000000000000d400 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.8-24.10-default uhci_hcd usb usb1: SerialNumber: 0000:00:10.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 209 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: irq 209, io base 000000000000d800 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.8-24.10-default uhci_hcd usb usb2: SerialNumber: 0000:00:10.1 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 209 uhci_hcd 0000:00:10.2: UHCI Host Controller ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800009eedca] uhci_hcd 0000:00:10.2: irq 209, io base 000000000000e000 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.8-24.10-default uhci_hcd usb usb3: SerialNumber: 0000:00:10.2 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 209 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: irq 209, io base 000000000000e400 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.8-24.10-default uhci_hcd usb usb4: SerialNumber: 0000:00:10.3 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 209 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: irq 209, pci mem ffffff0000f6c000 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 usb usb5: Product: EHCI Host Controller usb usb5: Manufacturer: Linux 2.6.8-24.10-default ehci_hcd usb usb5: SerialNumber: 0000:00:10.4 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected st: Version 20040403, fixed bufsize 32768, s/g segs 256 Attached scsi tape st0 at scsi2, channel 0, id 4, lun 0 st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 1048575 ReiserFS: hdd1: found reiserfs format "3.6" with standard journal ReiserFS: hdd1: using ordered data mode reiserfs: using flush barriers ReiserFS: hdd1: journal params: device hdd1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdd1: checking transaction log (hdd1) reiserfs: disabling flush barriers on hdd1 ReiserFS: hdd1: Using r5 hash to sort names ReiserFS: hdc1: found reiserfs format "3.6" with standard journal ReiserFS: hdc1: using ordered data mode reiserfs: using flush barriers ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdc1: checking transaction log (hdc1) ReiserFS: hdc1: Using r5 hash to sort names subfs 0.9 Device not ready. Make sure there is a disc in the drive. Attached scsi generic sg0 at scsi2, channel 0, id 3, lun 0, type 0 Attached scsi generic sg1 at scsi2, channel 0, id 4, lun 0, type 1 Attached scsi generic sg2 at scsi2, channel 0, id 6, lun 0, type 0 Device not ready. Make sure there is a disc in the drive. hda: DMA disabled hdb: DMA disabled eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU1] (supports C1) via82xx: Assuming DXS channels with 48k fixed sample rate. Please try dxs_support=1 or dxs_support=4 option and report if it works on your machine. ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:11.5 to 64 NET: Registered protocol family 10 Disabled Privacy Extensions on device ffffffff803e2f40(lo) IPv6 over IPv4 tunneling driver Installing knfsd (copyright (C) 1996 okir@monad.swb.de). powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09b) powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x8 (1350 mV) powernow-k8: 2 : fid 0xc (2000 MHz), vid 0x6 (1400 mV) powernow-k8: cpu_init done, current fid 0xc, vid 0x4 powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed powernow-k8: vid trans failed, vid 0x3, curr 0x4 powernow-k8: transition frequency failed BIOS EDD facility v0.16 2004-Jun-25, 4 devices found parport0: PC-style at 0x378 [PCSPP] parport0: Printer, HEWLETT-PACKARD DESKJET 3816 lp0: using parport0 (polling). drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 inserting floppy driver for 2.6.8-24.10-default Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 end_request: I/O error, dev fd0, sector 0 end_request: I/O error, dev fd0, sector 0 Device not ready. Make sure there is a disc in the drive. Disabled Privacy Extensions on device 00000100316d7000(sit0) eth0: no IPv6 routers present Unable to identify CD-ROM format. UDF-fs: No partition found (1) subfs: unsuccessful attempt to mount media (256) Unable to identify CD-ROM format. UDF-fs: No partition found (1) subfs: unsuccessful attempt to mount media (256) Unable to identify CD-ROM format. UDF-fs: No partition found (1) subfs: unsuccessful attempt to mount media (256) Unable to identify CD-ROM format. UDF-fs: No partition found (1) subfs: unsuccessful attempt to mount media (256) Unable to identify CD-ROM format. UDF-fs: No partition found (1) subfs: unsuccessful attempt to mount media (256) Unable to identify CD-ROM format. UDF-fs: No partition found (1) subfs: unsuccessful attempt to mount media (256) hda: packet command error: status=0x51 { DriveReady SeekComplete Error } hda: packet command error: error=0x54 ide: failed opcode was 100 hda: packet command error: status=0x51 { DriveReady SeekComplete Error } hda: packet command error: error=0x54 ide: failed opcode was 100 hda: packet command error: status=0x51 { DriveReady SeekComplete Error } hda: packet command error: error=0x54 ide: failed opcode was 100 CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP Deflate Compression module registered