Am Samstag, 25. Dezember 2004 19:42 schrieb Torsten Hallmann:
Am Sa, den 25.12.2004 schrieb Al Bogner um 18:19:
Reicht es "ide=reverse" einfach bei der Installation anzugeben oder ist da mehr zu tun?
Ja, das sollte reichen. Dann werden die Controller in der Reihenfolge getauscht.
Schön langsam drehe ich mit dieser S-ATA-HD durch. Nach dem Flashen des Bios sah es erst Mal gut aus. Doch nun kommt es wieder _manchmal_ dazu, dass die S-ATA von der 9.1-Installations-CD oder DVD nicht gefunden wird. Neuerdings tritt das ziemlich sicher mit ide=reverse auf. Die Fehlermeldungen beim Starten der Installation weisen auf ein IRQ-Problem hin und ich sah irgendmal ein Problem mit IRQ 15, sodass ich auf "enabled" im Bios umstellte. Relativ wahrscheinlich schafft man es, eine Installation zu starten, nach eigenen Vorstellungen zu partitionieren und es werden in Folge auch Pakete installiert. Nach dem 1. Reboot hängt das System aber bei verschiedenen Installations-Varianten mit "Grub loading stage 2". Mit einer "Neuinstallation / installiertes System booten" kann man fertig installieren und nun auch via Ethernet auf den Rechner zugreifen. Im Bios ist die Bootreihenfolge Floppy / CDROM / IDE-0 eingestellt, sowie "S-ATA-Boot" und "Boot other". Das hat die Installation angelegt: ------------------------------------------------------------------------------ cat menu.lst # Modified by YaST2. Last modification on Wed Oct 15 10:53:06 2003 color white/blue black/light-gray default 0 timeout 8 ###Don't change this comment - YaST2 identifier: Original name: linux### title Linux kernel (hd2,4)/vmlinuz root=/dev/hda7 splash=silent desktop resume=/dev/hda6 showopts initrd (hd2,4)/initrd ###Don't change this comment - YaST2 identifier: Original name: floppy### title Diskette root (fd0) chainloader +1 ###Don't change this comment - YaST2 identifier: Original name: failsafe### title Failsafe kernel (hd2,4)/vmlinuz root=/dev/hda7 showopts ide=nodma apm=off acpi=off vga=normal noresume nosmp noapic maxcpus=0 3 initrd (hd2,4)/initrd ------------------------------------------------------------------------------ Die Fat-Partition habe ich angelegt um eventuell unter DOS Fehler speichern zu können, aber mittlerweile habe ich einen Netzwerkzugang geschafft. hda ist die S-ATA-HD. fdisk -l Disk /dev/hda: 203.9 GB, 203928109056 bytes 255 heads, 63 sectors/track, 24792 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1 496 3984088+ b W95 FAT32 /dev/hda2 497 24790 195141555 f W95 Ext'd (LBA) /dev/hda5 497 504 64228+ 83 Linux /dev/hda6 505 581 618471 82 Linux swap /dev/hda7 582 24790 194458761 83 Linux Disk /dev/hde: 123.5 GB, 123522416640 bytes 255 heads, 63 sectors/track, 15017 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hde1 1 6528 52436128+ 83 Linux /dev/hde2 6529 14426 63440685 83 Linux /dev/hde3 * 14427 15016 4739175 83 Linux ------------------------------------------------------------------------------ Disk /dev/hdh: 60.0 GB, 60022480896 bytes 16 heads, 63 sectors/track, 116301 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Device Boot Start End Blocks Id System /dev/hdh1 1 116301 58615672+ 83 Linux ------------------------------------------------------------------------------ cat /etc/fstab /dev/hda7 / reiserfs acl,user_xattr 1 1 /dev/hda5 /boot ext3 acl,user_xattr 1 2 /dev/hde1 /data1 auto noauto,user 0 0 /dev/hde2 /data2 auto noauto,user 0 0 /dev/hde3 /data3 auto noauto,user 0 0 /dev/hdh1 /data4 auto noauto,user 0 0 /dev/hda6 swap swap pri=42 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 proc /proc proc defaults 0 0 usbfs /proc/bus/usb usbfs noauto 0 0 sysfs /sys sysfs noauto 0 0 /dev/dvd /media/dvd subfs fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=utf8 0 0 /dev/fd0 /media/floppy subfs fs=floppyfss,procuid,nodev,nosuid,sync 0 0 ------------------------------------------------------------------------------ Al