Howdy Newsgroup, es geht um folgendes: SuSe Linux 8.2 mit Linux mail 2.4.20-4GB-athlon #1 Mon Mar 17 17:56:47 UTC 2003 i686 unknown unknown GNU/Linux mit eth1 Link encap:Ethernet HWaddr 00:E0:81:51:D0:DD inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe51:d0dd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:30645562 errors:0 dropped:0 overruns:0 frame:0 TX packets:29430617 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1772521077 (1690.4 Mb) TX bytes:1216538621 (1160.1 Mb) Interrupt:10 Memory:fc980000-fc990000 mit Description Broadcom BCM5704 1000Base-T Driver_Name bcm5700 Driver_Version 7.1.22 Bootcode_Version 5704-v3.19 PCI_Vendor 0x14e4 PCI_Device_ID 0x1648 PCI_Subsystem_Vendor 0x14e4 PCI_Subsystem_ID 0x1644 PCI_Revision_ID 0x03 PCI_Slot 9 PCI_Function 0 PCI_Bus 2 PCI_Bus_Speed 64-bit PCIX 100MHz Memory 0xfc980000 IRQ 10 System_Device_Name eth1 Current_HWaddr 00:e0:81:51:d0:dd Permanent_HWaddr 00:e0:81:51:d0:dd Part_Number BCM95704A7 Link up Auto_Negotiate on Speed_Advertisement 10half 10full 100half 100full 1000half 1000full Flow_Control_Advertisement pause Speed 100 Duplex full Flow_Control receive/transmit State up MTU_Size 1500 Rx_Packets 30648425 Tx_Packets 29433496 Rx_Bytes 1772794816 Tx_Bytes 1216898110 Rx_Errors 0 Tx_Errors 0 Tx_Carrier_Errors 0 Tx_Abort_Excess_Coll 0 Tx_Abort_Late_Coll 0 Tx_Deferred_Ok 0 Tx_Single_Coll_Ok 0 Tx_Multi_Coll_Ok 0 Tx_Total_Coll_Ok 0 Tx_XON_Pause_Frames 0 Tx_XOFF_Pause_Frames 0 Rx_CRC_Errors 0 Rx_Short_Fragment_Errors 0 Rx_Short_Length_Errors 0 Rx_Long_Length_Errors 0 Rx_Align_Errors 0 Rx_Overrun_Errors 0 Rx_XON_Pause_Frames 0 Rx_XOFF_Pause_Frames 0 Tx_MAC_Errors 0 Rx_MAC_Errors 0 Tx_Checksum on Rx_Checksum on Scatter_Gather on VLAN off NIC_Tx_BDs off Tx_Desc_Count 120 Rx_Desc_Count 200 Rx_Jumbo_Desc_Count 0 Adaptive_Coalescing off Rx_Coalescing_Ticks 18 Rx_Coalesced_Frames 6 Tx_Coalescing_Ticks 200 Tx_Coalesced_Frames 35 Stats_Coalescing_Ticks 1000000 Wake_On_LAN off Ich bekomme eth1 nicht auf 1000Base-T. Mit ethtool gehts auch nicht: #ethtool -s eth1 speed 1000 Cannot set new settings: Invalid argument not setting speed Irgendeine Idee ? Bei einem anderen Server (mit gleicher Netzwerkkarte) mit SuSE Linux 8.1 klappts wunderbar. (ganz von alleine) Irgendeine Idee ? Gruß, Zafer.