Hallo!
Ich hab mir einen USB Ethernet Adapter von CMC gekauft.
habe ich einfach mit yast das Device eth2 angelegt (kein USB ankreuzen) und dann die IP-Adresse etc. vergeben. Und schon ging es ins Internet. ;-) Das hat geklappt.
Der Adapter läuft auch prima, nur bekomme ich jetzt über mein onboard NIC (100mbit) mit Samba sagenhafte 25Kb/s. Sogar bei VNC macht sich das bemerkbar. Wie kommt es, dass sich dieser USB-Treiber (kaweth.o?) auf den anderen Netzwerkadapter auswirkt? System: SuSE 8.1 eth0 via-Rhine II (100mbit) eth1 USB-Ethernet-Adapter CMC UE-100, kaweth.o linux:~ # ifconfig eth0 Link encap:Ethernet HWaddr 00:40:63:C0:CB:1A inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::240:63ff:fec0:cb1a/10 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22820 errors:0 dropped:0 overruns:0 frame:0 TX packets:35079 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1504445 (1.4 Mb) TX bytes:27183513 (25.9 Mb) Interrupt:10 Base address:0xe800 eth1 Link encap:Ethernet HWaddr 00:50:5B:00:04:4C inet addr:192.168.2.22 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::250:5bff:fe00:44c/10 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1514 Metric:1 RX packets:1838 errors:0 dropped:0 overruns:0 frame:0 TX packets:1867 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:646071 (630.9 Kb) TX bytes:186757 (182.3 Kb) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:798 errors:0 dropped:0 overruns:0 frame:0 TX packets:798 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:84539 (82.5 Kb) TX bytes:84539 (82.5 Kb) ppp0 Link encap:Point-to-Point Protocol inet addr:xxx.xxx.xxx.xxx P-t-P:xxx.xxx.xxx.xxx Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:1796 errors:0 dropped:0 overruns:0 frame:0 TX packets:1821 errors:0 dropped:4 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:604033 (589.8 Kb) TX bytes:145132 (141.7 Kb) linux:~ # less /var/log/messages [...] Jan 1 22:31:39 (none) kernel: hub.c: USB new device connect on bus1/1, assigned device number 3 Jan 1 22:31:39 (none) kernel: usb.c: USB device 3 (vend/prod 0x5e9/0x8) is not claimed by any active driver. Jan 1 22:31:41 (none) kernel: kaweth.c: Driver loading Jan 1 22:31:41 (none) kernel: usb.c: registered new driver kaweth Jan 1 22:31:41 (none) kernel: kaweth.c: Kawasaki Device Probe (Device number:3): 0x05e9:0x0008:0x0008 Jan 1 22:31:41 (none) kernel: kaweth.c: Device at c2db4200 Jan 1 22:31:41 (none) kernel: kaweth.c: Descriptor length: 12 type: 1 Jan 1 22:31:41 (none) kernel: kaweth.c: Resetting. Jan 1 22:31:41 (none) kernel: kaweth.c: kaweth_reset(c8cb0000) Jan 1 22:31:41 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:41 (none) kernel: kaweth.c: kaweth_reset() returns 0. Jan 1 22:31:41 (none) kernel: kaweth.c: Downloading firmware... Jan 1 22:31:41 (none) kernel: kaweth.c: High: 12, Low:197 Jan 1 22:31:41 (none) kernel: kaweth.c: Downloading firmware at cd7da500 to kaweth device at c8cb0000 Jan 1 22:31:41 (none) kernel: kaweth.c: Firmware length: 3276 Jan 1 22:31:41 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:42 (none) kernel: kaweth.c: High: 2, Low:103 Jan 1 22:31:42 (none) kernel: kaweth.c: Downloading firmware at cd7db1e0 to kaweth device at c8cb0000 Jan 1 22:31:42 (none) kernel: kaweth.c: Firmware length: 622 Jan 1 22:31:42 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:42 (none) kernel: kaweth.c: High: 0, Low:175 Jan 1 22:31:42 (none) kernel: kaweth.c: Downloading firmware at cd7da420 to kaweth device at c8cb0000 Jan 1 22:31:42 (none) kernel: kaweth.c: Firmware length: 182 Jan 1 22:31:42 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:42 (none) kernel: kaweth.c: High: 0, Low:15 Jan 1 22:31:42 (none) kernel: kaweth.c: Downloading firmware at cd7da4d6 to kaweth device at c8cb0000 Jan 1 22:31:42 (none) kernel: kaweth.c: Firmware length: 22 Jan 1 22:31:42 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:42 (none) kernel: kaweth.c: Triggering firmware Jan 1 22:31:42 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:42 (none) kernel: kaweth.c: Firmware loaded. I'll be back... Jan 1 22:31:42 (none) insmod: Using /lib/modules/2.4.19-4GB/kernel/drivers/usb/kaweth.o Jan 1 22:31:42 (none) insmod: Symbol version prefix '' Jan 1 22:31:42 (none) kernel: usb.c: USB disconnect on device 3 Jan 1 22:31:43 (none) /etc/hotplug/usb.agent[2760]: writing usb-1-3 to /var/run/hotplug/net Jan 1 22:31:47 (none) kernel: hub.c: USB new device connect on bus1/1, assigned device number 4 Jan 1 22:31:47 (none) kernel: kaweth.c: Kawasaki Device Probe (Device number:4): 0x05e9:0x0008:0x0208 Jan 1 22:31:47 (none) kernel: kaweth.c: Device at c2db4200 Jan 1 22:31:47 (none) kernel: kaweth.c: Descriptor length: 12 type: 1 Jan 1 22:31:47 (none) kernel: kaweth.c: Resetting. Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_reset(c8cb0000) Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_reset() returns 0. Jan 1 22:31:47 (none) kernel: kaweth.c: Firmware present in device. Jan 1 22:31:47 (none) kernel: kaweth.c: Reading kaweth configuration Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:47 (none) kernel: kaweth.c: Statistics collection: 13fbffff Jan 1 22:31:47 (none) kernel: kaweth.c: Multicast filter limit: 80 Jan 1 22:31:47 (none) kernel: kaweth.c: MTU: 1514 Jan 1 22:31:47 (none) kernel: kaweth.c: Read MAC address 00:50:5b:00:04:4c Jan 1 22:31:47 (none) kernel: kaweth.c: Setting URB size to 1664 Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:47 (none) kernel: kaweth.c: Set SOFS wait to 5 Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:47 (none) kernel: kaweth.c: Set receive filter to 28 Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:31:47 (none) kernel: kaweth.c: Initializing net device. Jan 1 22:31:47 (none) kernel: kaweth.c: kaweth interface created at eth1 Jan 1 22:31:47 (none) kernel: kaweth.c: Kaweth probe returning. Jan 1 22:31:48 (none) /etc/hotplug/net.agent[2843]: Using HW description eth-usb-1-3 Jan 1 22:31:50 (none) /etc/hotplug/usb.agent[2881]: writing usb-1-4 to /var/run/hotplug/net Jan 1 22:33:08 (none) ifdown-route: interface eth1 is not up Jan 1 22:33:12 (none) kernel: kaweth.c: Dev usage: 1 Jan 1 22:33:12 (none) kernel: kaweth.c: Opening network device. Jan 1 22:33:12 (none) kernel: kaweth.c: Setting Rx mode to 28 Jan 1 22:33:12 (none) last message repeated 4 times Jan 1 22:33:13 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:33:13 (none) kernel: kaweth.c: in_interrupt() Jan 1 22:33:13 (none) kernel: kaweth.c: Failed to set Rx mode: -16 Jan 1 22:33:13 (none) kernel: kaweth.c: Setting Rx mode to 28 Jan 1 22:33:13 (none) modify_resolvconf: Service smpppd tried to modify resolver configuration, but it Jan 1 22:33:13 (none) modify_resolvconf: was not modified due to MODIFY_RESOLV\NAMED_CONF_DYNAMICALLY=no Jan 1 22:33:13 (none) pppd[3427]: Plugin pppoe.so loaded. Jan 1 22:33:13 (none) pppd[3427]: PPPoE Plugin Initialized Jan 1 22:33:13 (none) pppd[3427]: Plugin passwordfd.so loaded. Jan 1 22:33:13 (none) pppd[3427]: pppd 2.4.1 started by root, uid 0 Jan 1 22:33:13 (none) pppd[3427]: Using interface ppp0 Jan 1 22:33:13 (none) pppd[3427]: Setting MTU to 1492. Jan 1 22:33:13 (none) pppd[3427]: Couldn't increase MRU to 1500 Jan 1 22:33:13 (none) pppd[3427]: local IP address 192.168.99.1 Jan 1 22:33:13 (none) pppd[3427]: remote IP address 192.168.99.99 Jan 1 22:33:14 (none) kernel: kaweth.c: kaweth_control() Jan 1 22:33:14 (none) kernel: kaweth.c: in_interrupt() Jan 1 22:33:14 (none) kernel: kaweth.c: Failed to set Rx mode: -16 Jan 1 22:33:23 (none) kernel: eth0: no IPv6 routers present Jan 1 22:33:23 (none) kernel: eth1: no IPv6 routers present Jan 1 22:33:39 (none) pppd[3427]: Starting link Jan 1 22:33:39 (none) pppd[3427]: Sending PADI Jan 1 22:33:39 (none) pppd[3427]: HOST_UNIQ successful match Jan 1 22:33:40 (none) pppd[3427]: HOST_UNIQ successful match Jan 1 22:33:40 (none) pppd[3427]: Got connection: 165c Jan 1 22:33:40 (none) pppd[3427]: Connecting PPPoE socket: 00:90:1a:10:11:bc 5c16 eth1 0x80880a8 Jan 1 22:33:40 (none) pppd[3427]: Connect: ppp0 <--> eth1 Jan 1 22:33:40 (none) pppd[3427]: Setting MTU to 1492. Jan 1 22:33:40 (none) pppd[3427]: Couldn't increase MRU to 1500 Jan 1 22:33:42 (none) pppd[3427]: Setting MTU to 1492. Jan 1 22:33:42 (none) pppd[3427]: Remote message: Authorization - Success Jan 1 22:33:42 (none) pppd[3427]: Local IP address changed to xxx.xxx.xxx.xxx Jan 1 22:33:42 (none) pppd[3427]: Remote IP address changed to xxx.xxx.xxx.xxx Jan 1 22:33:43 (none) pppd[3427]: Open ICMP xxx.xxx.xxx.xxx -> xxx.xxx.xxx.xxx Jan 1 22:33:43 (none) modify_resolvconf: Service pppd tried to modify resolver configuration, but it Jan 1 22:33:43 (none) modify_resolvconf: was not modified due to MODIFY_RESOLV\NAMED_CONF_DYNAMICALLY=no ++++++> ip-up.local gestartet Jan 1 22:33:43 (none) pppd[3427]: Script /etc/ppp/ip-up finished (pid 3737), status = 0x0 Sind weitere Log-Files oder Infos nötig? Schonmal wieder Danke für die Hilfe im Voraus! Gruss, Matthias