hat sich erledigt! danke!
----- Original Message -----
From: "Jack McDowald"
hallo lebensretter!
ich bin verzweifelt! ich versuche krampfhaft auf einer linux 7.0 - maschine eine teles 16.3 PnP isdn-karte einzurichten (soll ein dial-in voiceserver werden). die zickt aber noch richtig.
ich hab isdn4linux natürlich aktiviert und alles soweit von hand eingestellt, folgende fehlermeldung wirft dann aber /var/log/warn aus:
Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ(9) getting no interrupts during init 1 Jul 16 01:45:37 bayonne kernel: bug: kernel timer added twice at c48bc4ab. Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ(9) getting no interrupts during init 2 Jul 16 01:45:37 bayonne kernel: bug: kernel timer added twice at c48bc4ab. Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ(9) getting no interrupts during init 3 Jul 16 01:45:37 bayonne kernel: HiSax: Card Teles 16.3c not installed !
und /var/log/messages gibt folgendes aus:
Jul 16 01:45:36 bayonne kernel: ISDN subsystem Rev: 1.108/1.92/1.134/1.77/1.21/1.5 loaded Jul 16 01:45:36 bayonne kernel: HiSax: Linux Driver for passive ISDN cards Jul 16 01:45:36 bayonne kernel: HiSax: Version 3.5 (module) Jul 16 01:45:36 bayonne kernel: HiSax: Layer1 Revision 2.39 Jul 16 01:45:36 bayonne kernel: HiSax: Layer2 Revision 2.23 Jul 16 01:45:36 bayonne kernel: HiSax: TeiMgr Revision 2.15 Jul 16 01:45:36 bayonne kernel: HiSax: Layer3 Revision 2.14 Jul 16 01:45:36 bayonne kernel: HiSax: LinkLayer Revision 2.47 Jul 16 01:45:36 bayonne kernel: HiSax: Approval certification valid Jul 16 01:45:36 bayonne kernel: HiSax: Approved with ELSA Microlink PCI cards Jul 16 01:45:36 bayonne kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI cards Jul 16 01:45:36 bayonne kernel: HiSax: Approved with Sedlbauer Speedfax + cards Jul 16 01:45:36 bayonne kernel: HiSax: Warning - no protocol specified Jul 16 01:45:36 bayonne kernel: HiSax: Note! module load syntax has changed. Jul 16 01:45:36 bayonne kernel: HiSax: using protocol EURO Jul 16 01:45:36 bayonne kernel: HiSax: Total 1 card defined Jul 16 01:45:36 bayonne kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) Jul 16 01:45:36 bayonne kernel: HiSax: HFC-S driver Rev. 1.7 Jul 16 01:45:36 bayonne kernel: HFCS: defined at 0x580 IRQ 9 HZ 100 Jul 16 01:45:37 bayonne kernel: HFCS: resetting card Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ 9 count 0 Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ 9 count 0 Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ(9) getting no interrupts during init 1 Jul 16 01:45:37 bayonne kernel: HFCS: resetting card Jul 16 01:45:37 bayonne kernel: bug: kernel timer added twice at c48bc4ab. Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ 9 count 0 Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ(9) getting no interrupts during init 2 Jul 16 01:45:37 bayonne kernel: HFCS: resetting card Jul 16 01:45:37 bayonne kernel: bug: kernel timer added twice at c48bc4ab. Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ 9 count 0 Jul 16 01:45:37 bayonne kernel: Teles 16.3c: IRQ(9) getting no interrupts during init 3 Jul 16 01:45:37 bayonne kernel: HiSax: Card Teles 16.3c not installed ! Jul 16 01:45:37 bayonne kernel: ISDN-subsystem unloaded
meine /etc/rc.config.d/i4l_hardware.rc.config sieht so aus:
# # driver-id for card identification # set to "HiSax" # or whatever you defined when loading driver within kernel # I4L_ID_1="HiSax"
# # D-channel protocol 1=1TR6, 2=EDSS1(Euro-ISDN) 3=leased 4=NI1 # I4L_PROTOCOL_1="2"
# Type ISDN-card # HiSax passiv type 1...7999 (used 37) # AVM active type 8001 # Eicon active type 8010 # IBM active type 8020 # ICN active type 8030
I4L_TYPE_1="4"
# # Subtype of a given type # I4L_SUBTYPE_1="0"
# # used IRQ if any # eg. 12 or 15 when loading as module # set to "" when driver is loaded within kernel # I4L_IRQ_1="9"
# # Membase if any # I4L_MEMBASE_1="0xd0000"
# # IO address if any # I4L_IO_1="0x580"
# # IO0 (ISA PnP) # I4L_IO0_1="0x580"
# # IO1 (ISA PnP) # I4L_IO1_1="0x580"
# # IO2 (ISA PnP) # I4L_IO2_1="0x580"
# # for backward compatibility # HiSax-modul: the complete line to load module # e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and # ELSA QuickStep1000 PCI, Euro ISDN: # "type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa" # # is equivalent for follow commandline # modprobe hisax type=5,18 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa # I4L_MODUL_OPTIONS_1="type=14 io=0x580 irq=9"
# # specials # # Debug Level, 4 (default) # I4L_HISAXDEBUG_1=""
# # EAZ mapping set # eg: I4L_EAZMAP_1="280,280,280,283,283,280,-,-"
I4L_EAZMAP_1=""
auch wenn ich I4L_TYPE_1="14" statt 4 setze, bringt das nichts.
bitte helft mir!!!!
gruß jack mcdowald
-- Um die Liste abzubestellen, schicken Sie eine Mail an: suse-linux-unsubscribe@suse.com Um eine Liste aller verfügbaren Kommandos zu bekommen, schicken Sie eine Mail an: suse-linux-help@suse.com