Hallo,
Systemkonfiguration :
Linux : Suse 7.0, Kernel 2.2.16
HW : GA-6BXDU, 1GB RAM, Dual PIII 450
HD-Ctrl. : ADAPTEC 29160 und 2940, sowie
der Onboard vom Mainboard.
Mein Server läuft und steht, usw.
ping ging bei jedem Stillstand noch.
telnet und andere dienste waren nicht moeglich.
Ich weiß nicht mehr ob die Hardware
oder Software oder beides Schuld ist.
Die Konfiguraion koennt ihr der boot.msg entnhemen.
Hinzukommt zu dem ganzen Dilemma, daß mit 2.2.16
das Backup mit ARKEIA ohne Probleme und zwar wirklich
ohne jegliche Probleme lief.
Mit Kernel 2.2.19 gab es gravierdende Probleme : Backup
wurde einfach nicht fertig. Lief auch noch nach 48 Stunden
wozu es sonst nur 6 Stunden benoetigte.
Mit Kernel 2.2.18, konnte ich mich nicht mal
mehr beim User-Interface von ARKEIA anmelden.
Wer von euch hat Rat und/oder Tat ?
Gruß
Thomas Reichel
hier die aktuelle boot.msg
------------ schnipp ------------------
Inspecting /boot/System.map-2.2.16-SMP
Loaded 6614 symbols from /boot/System.map-2.2.16-SMP.
Symbols match kernel version 2.2.16.
Loaded 87 symbols from 6 modules.
klogd 1.3-3, log source = ksyslog started.
<4>Linux version 2.2.16-SMP (root@r5) (gcc version 2.95.2 19991024
(release)) #10 SMP Tue Nov 21 20:42:27 CET 2000
<4>Warning only 960MB will be used.
<4>Intel MultiProcessor Specification v1.1
<4> Virtual Wire compatibility mode.
<4>OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
<4>Processor #0 Pentium(tm) Pro APIC version 17
<4>Processor #1 Pentium(tm) Pro APIC version 17
<4>I/O APIC #2 Version 17 at 0xFEC00000.
<4>Processors: 2
<4>mapped APIC to ffffe000 (fee00000)
<4>mapped IOAPIC to ffffd000 (fec00000)
<4>Detected 448809 kHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 894.57 BogoMIPS
<4>Memory: 971384k/983040k available (1036k kernel code, 424k reserved,
10124k data, 72k init, 0k bigmem)
<4>Dentry hash table entries: 131072 (order 8, 1024k)
<4>Buffer cache hash table entries: 524288 (order 9, 2048k)
<4>Page cache hash table entries: 262144 (order 8, 1024k)
<5>VFS: Diskquotas version dquot_6.4.0 initialized
<6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
<4>per-CPU timeslice cutoff: 100.11 usecs.
<4>CPU0: Intel Pentium III (Katmai) stepping 03
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 448.8217 MHz.
<4>..... system bus clock speed is 99.7379 MHz.
<4>Booting processor 1 eip 2000
<4>Calibrating delay loop... 894.57 BogoMIPS
<4>OK.
<4>CPU1: Intel Pentium III (Katmai) stepping 03
<6>Total of 2 processors activated (1789.13 BogoMIPS).
<4>enabling symmetric IO mode... ...done.
<4>ENABLING IO-APIC IRQs
<4>init IO_APIC IRQs
<4> IO-APIC (apicid-pin) 2-0, 2-10, 2-11, 2-14, 2-15, 2-20, 2-21, 2-22, 2-23
not connected.
<4>number of MP IRQ sources: 16.
<4>number of IO-APIC #2 registers: 24.
<4>testing the IO APIC.......................
<4>
<4>IO APIC #2......
<4>.... register #00: 02000000
<4>....... : physical APIC id: 02
<4>.... register #01: 00170011
<4>....... : max redirection entries: 0017
<4>....... : IO APIC version: 0011
<4>.... register #02: 00000000
<4>....... : arbitration: 00
<4>.... IRQ redirection table:
<4> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<4> 00 000 00 1 0 0 0 0 0 0 00
<4> 01 000 00 0 0 0 0 0 1 1 59
<4> 02 0FF 0F 0 0 0 0 0 1 1 51
<4> 03 000 00 0 0 0 0 0 1 1 61
<4> 04 000 00 0 0 0 0 0 1 1 69
<4> 05 000 00 0 0 0 0 0 1 1 71
<4> 06 000 00 0 0 0 0 0 1 1 79
<4> 07 000 00 0 0 0 0 0 1 1 81
<4> 08 000 00 0 0 0 0 0 1 1 89
<4> 09 000 00 0 0 0 0 0 1 1 91
<4> 0a 000 00 1 0 0 0 0 0 0 00
<4> 0b 000 00 1 0 0 0 0 0 0 00
<4> 0c 000 00 0 0 0 0 0 1 1 99
<4> 0d 000 00 1 0 0 0 0 0 0 00
<4> 0e 000 00 1 0 0 0 0 0 0 00
<4> 0f 000 00 1 0 0 0 0 0 0 00
<4> 10 0FF 0F 1 1 0 1 0 1 1 A1
<4> 11 0FF 0F 1 1 0 1 0 1 1 A9
<4> 12 0FF 0F 1 1 0 1 0 1 1 B1
<4> 13 0FF 0F 1 1 0 1 0 1 1 B9
<4> 14 000 00 1 0 0 0 0 0 0 00
<4> 15 000 00 1 0 0 0 0 0 0 00
<4> 16 000 00 1 0 0 0 0 0 0 00
<4> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 2
<7>IRQ1 -> 1
<7>IRQ3 -> 3
<7>IRQ4 -> 4
<7>IRQ5 -> 5
<7>IRQ6 -> 6
<7>IRQ7 -> 7
<7>IRQ8 -> 8
<7>IRQ9 -> 9
<7>IRQ10 -> 17
<7>IRQ11 -> 19
<7>IRQ12 -> 12
<7>IRQ13 -> 13
<7>IRQ14 -> 18
<7>IRQ15 -> 16
<4>.................................... done.
<4>checking TSC synchronization across CPUs: passed.
<4>PCI: PCI BIOS revision 2.10 entry at 0xfb140, last bus=2
<4>PCI: Using configuration type 1
<4>PCI: Probing PCI hardware
<6>Linux NET4.0 for Linux 2.2
<6>Based upon Swansea University Computer Society NET3.039
<6>NET4: Unix domain sockets 1.0 for Linux NET4.0.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<4>TCP: Hash tables configured (ehash 524288 bhash 65536)
<4>Initializing RT netlink socket
<4>Starting kswapd v 1.5
<6>Detected PS/2 Mouse Port.
<4>pty: 2048 Unix98 ptys configured
<6>Real Time Clock Driver v1.09
<4>md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
<6>(scsi0) found at PCI
0/8/0
<6>(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
<6>(scsi0) Downloading sequencer code... 392 instructions downloaded
<6>(scsi1) found at PCI
0/9/0
<6>(scsi1) Wide Channel, SCSI ID=7, 32/255 SCBs
<6>(scsi1) Downloading sequencer code... 392 instructions downloaded
<6>(scsi2) <Adaptec AHA-2940A Ultra SCSI host adapter> found at PCI 0/10/0
<6>(scsi2) Narrow Channel, SCSI ID=7, 3/255 SCBs
<6>(scsi2) Downloading sequencer code... 422 instructions downloaded
<6>(scsi3) found at PCI 0/12/0
<6>(scsi3) Wide Channel A, SCSI ID=7, 32/255 SCBs
<6>(scsi3) Downloading sequencer code... 392 instructions downloaded
<6>(scsi4) found at PCI 0/12/1
<6>(scsi4) Wide Channel B, SCSI ID=7, 32/255 SCBs
<6>(scsi4) Downloading sequencer code... 392 instructions downloaded
<4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<4>
<4>scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<4>
<4>scsi2 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<4> <Adaptec AHA-2940A Ultra SCSI host adapter>
<4>scsi3 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<4>
<4>scsi4 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
<4>
<4>scsi : 5 hosts.
<6>(scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DPSS-309170N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
<6>(scsi0:0:11:0) Synchronous at 160.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DDYS-T18350N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdb at scsi0, channel 0, id 11, lun 0
<6>(scsi0:0:12:0) Synchronous at 160.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DDYS-T18350N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdc at scsi0, channel 0, id 12, lun 0
<6>(scsi0:0:13:0) Synchronous at 160.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DDYS-T36950N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdd at scsi0, channel 0, id 13, lun 0
<6>(scsi0:0:14:0) Synchronous at 160.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DDYS-T36950N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sde at scsi0, channel 0, id 14, lun 0
<6>(scsi1:0:1:0) Synchronous at 40.0 Mbyte/sec, offset 15.
<4> Vendor: IBM Model: DGVS09U Rev: 03B0
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdf at scsi1, channel 0, id 1, lun 0
<6>(scsi1:0:2:0) Synchronous at 40.0 Mbyte/sec, offset 15.
<4> Vendor: IBM Model: DGVS09U Rev: 03B0
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdg at scsi1, channel 0, id 2, lun 0
<6>(scsi1:0:4:0) Synchronous at 20.0 Mbyte/sec, offset 15.
<4> Vendor: IBM Model: DCAS-34330 Rev: S61A
<4> Type: Direct-Access ANSI SCSI revision: 02
<4>Detected scsi disk sdh at scsi1, channel 0, id 4, lun 0
<6>(scsi1:0:5:0) Synchronous at 20.0 Mbyte/sec, offset 15.
<4> Vendor: IBM Model: DCAS-34330 Rev: S65A
<4> Type: Direct-Access ANSI SCSI revision: 02
<4>Detected scsi disk sdi at scsi1, channel 0, id 5, lun 0
<6>(scsi1:0:6:0) Synchronous at 20.0 Mbyte/sec, offset 16.
<4> Vendor: PIONEER Model: DVD-ROM DVD-304 Rev: 1.03
<4> Type: CD-ROM ANSI SCSI revision: 02
<6>(scsi1:0:8:0) Synchronous at 160.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DDYS-T36950N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdj at scsi1, channel 0, id 8, lun 0
<6>(scsi1:0:9:0) Synchronous at 160.0 Mbyte/sec, offset 63.
<4> Vendor: IBM Model: DDYS-T36950N Rev: S93E
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>Detected scsi disk sdk at scsi1, channel 0, id 9, lun 0
<6>(scsi2:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
<4> Vendor: HP Model: C1537A Rev: L708
<4> Type: Sequential-Access ANSI SCSI revision: 02
<6>(scsi2:0:2:0) Synchronous at 10.0 Mbyte/sec, offset 8.
<4> Vendor: HP Model: C1533A Rev: 9608
<4> Type: Sequential-Access ANSI SCSI revision: 02
<6>(scsi3:0:3:0) Synchronous at 40.0 Mbyte/sec, offset 15.
<4> Vendor: SONY Model: TSL-11000 Rev: L100
<4> Type: Sequential-Access ANSI SCSI revision: 02
<4> Vendor: SONY Model: TSL-11000 Rev: L100
<4> Type: Medium Changer ANSI SCSI revision: 02
<6>(scsi4:0:4:0) Synchronous at 40.0 Mbyte/sec, offset 15.
<4> Vendor: SONY Model: TSL-11000 Rev: L100
<4> Type: Sequential-Access ANSI SCSI revision: 02
<4> Vendor: SONY Model: TSL-11000 Rev: L100
<4> Type: Medium Changer ANSI SCSI revision: 02
<4>scsi : detected 11 SCSI disks total.
<4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 17916240 [8748 MB] [8.7
GB]<4>SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB]
[17.5 GB]
<4>SCSI device sdc: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB]
[17.5 GB]
<4>SCSI device sdd: hdwr sector= 512 bytes. Sectors= 71687340 [35003 MB]
[35.0 GB]
<4>SCSI device sde: hdwr sector= 512 bytes. Sectors= 71687340 [35003 MB]
[35.0 GB]
<4>SCSI device sdf: hdwr sector= 512 bytes. Sectors= 17829870 [8705 MB] [8.7
GB]<4>SCSI device sdg: hdwr sector= 512 bytes. Sectors= 17829870 [8705 MB]
[8.7 GB]<4>SCSI device sdh: hdwr sector= 512 bytes. Sectors= 8467200 [4134 MB]
[4.1 GB]
<4>SCSI device sdi: hdwr sector= 512 bytes. Sectors= 8467200 [4134 MB] [4.1
GB]
<4>SCSI device sdj: hdwr sector= 512 bytes. Sectors= 71687340 [35003 MB]
[35.0 GB]
<4>SCSI device sdk: hdwr sector= 512 bytes. Sectors= 71687340 [35003 MB]
[35.0 GB]
<4>Partition check:
<4> sda: sda1 < sda5 sda6 sda7 >
<4> sdb: sdb1 sdb2 sdb3 < sdb5 >
<4> sdc: sdc1 sdc2 sdc3 < sdc5 >
<4> sdd: sdd1 sdd2 sdd3 sdd4 < sdd5 >
<4> sde: sde1
<4> sdf: sdf1
<4> sdg: sdg1
<4> sdh: sdh1 sdh2
<4> sdi: sdi1 sdi2
<4> sdj: sdj1
<4> sdk: sdk1 sdk2 sdk3 < sdk5 >
<4>VFS: Mounted root (ext2 filesystem) readonly.
<4>Freeing unused kernel memory: 72k freed
<6>Adding Swap: 136512k swap-space (priority -1)
<4>Checking ReiserFS transaction log (device 08:91) ...
<4>Using tea hash to sort names
<4>ReiserFS core development sponsored by SuSE Labs (suse.com)
<4>Journaling sponsored by MP3.com
<4>ReiserFS version 3.5.23
<4>Checking ReiserFS transaction log (device 08:a5) ...
<4>Replayed 1 transactions in 2 seconds
<4>Using tea hash to sort names
<4>ReiserFS version 3.5.23
<4>Checking ReiserFS transaction log (device 08:a2) ...
<4>Using tea hash to sort names
<4>ReiserFS version 3.5.23
<4>Checking ReiserFS transaction log (device 08:a1) ...
<4>Replayed 1 transactions in 2 seconds
<4>Using tea hash to sort names
<4>ReiserFS version 3.5.23
<6>Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
------------ schnipp ------------------
Rechner steht :
2.2.16:
=======
14.11.00 18.11.00 21.11.00 1.12.00 9.12.00 11.12.00
13.12.00 14.12.00 17.12.00 21.12.00 22.12.00 25.12.00
2.1.01 12.1.01 16.1.01 17.1.01 18.1.01 19.1.01
25.1.01 26.1.01 2.2.01 5.2.01 9.2.01 10.2.01
12.2.01 13.2.01 14.2.01 17.2.01 27.2.01
....
8.4.01 2.5.01
8.6.01 <<<<<<----
8.6.01 27.6.01 28.6.01 30.6.01 1.7.01 2.7.01
3.7.01 4.7.01 10.7.01 23.7.01 30.7.01 31.7.01
1.8.01 7.8.01
Aus Sicherheitsgründen habe ich am 8.8.01
den Kernel 2.2.19 installiert. In diesem Moment
war mir nicht bewusst dass dieser nicht SMP
stabil ist.
Die neuen libs von suse wegen 2.2.19 hab ich installiert
sonst bootet er ja nicht mal.
8.8.01 ----> 2.2.19
======
15.8.01
17.8.01 18.8.01
heute erfuhr ich, dass 2.2.19 nicht SMP stabil ist.
jetzt ging ich 2.2.18, damit lief er ca. 22 Stunden.
======
jetzt bin ich wieder auf 2.2.16 und er steht jeden Tag.
======
--
GMX - Die Kommunikationsplattform im Internet.
http://www.gmx.net
