All I can say at the moment is I feel for you. I gave up yesterday and purchased 2 SCSI disks. (you can see all of my horrors in previous messages) It is probably 3/6 months too early for Sata(n) and linux. One of the posters, Frank did get his Sata disks running, but I have Seagate drives and he did not. There where a number of patches in Bart's siimage.c for seagates. Not sure this helps.
-----Original Message----- From: Steven A. DuChene [mailto:linux-clusters@mindspring.com] Sent: Tuesday, 23 December 2003 6:24 AM To: suse-amd64@suse.com Subject: [suse-amd64] Tyan 2885 and 2.6.0-test11-mm1 "no init found" on boot.iso
I am attempting to modify the SuSE9-AMD64 boot.iso so I can attempt to install SuSE9-X86_64 to a Tyan 2885 system with two SATA drives hung off of the Silicon Image 3114 controller. The system has 2Gb of memory (two 512Kb sticks stuck in each processor memory bank). I have the controller configured in IDE mode in the BIOS and I was able to build a 2.6 kernel (2.6.0-test11-mm1) that has the siimage driver in it that seems to recognize the drives during boot up. The SATA drives show up as hde and hdg. The CD/DVD drive hung off of the built in AMD8111 IDE controller shows up as hda. I have been unable to get this kernel placed on an altered SuSE9 boot.iso install image without causing various boot problems.
I have built the kernel with all of the appropriate drivers built into the kernel image so I shouldn't require any modules. I built in the following drivers:
Processor family (Opteron/Athlon64/Hammer/K8) Symmetric multi-processing support Allocate 3rd-level pagetables from highmem MTRR (Memory Type Range Register) support PCI support PCI access mode (Any) Vector-based interrupt indexing Legacy /proc/pci interface PCI device name database ISA support Plug and Play support Plug and Play BIOS support Plug and Play BIOS /proc interface Normal floppy disk support Loopback device support Broadcom Tigon3 support <<<<<<<<<< tg3 Silicon Image chipset support <<<<<<<<<< siimage Initial RAM disk (initrd) support Support for Large Block Devices ELF a.out MISC (executable format) Enable loadable module support Automatic kernel module loading RAM disk support (65536) Default RAM disk size ATA/ATAPI/MFM/RLL support AMD and nVidia IDE support (CD/DVD drive conntected to the onboard IDE controller) IDE/ATAPI CDROM support IDE/ATA-2 DISK support Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support IDE Taskfile IO (EXPERIMENTAL) PCI IDE chipset support Sharing PCI IDE interrupts support Generic PCI IDE Chipset Support Generic PCI bus-master DMA support Use PCI DMA by default when available Second extended fs support Ext3 journalling file system support ROM file system support ISO 9660 CDROM file system support Microsoft Joliet CDROM extensions UDF file system support DOS FAT fs support MSDOS fs support VFAT (Windows-95) fs support /proc file system support /dev/pts file system for Unix98 PTYs Virtual memory file system support (former shm fs) Compressed ROM file system support NFS file system support SCSI device support legacy /proc/scsi/ support SCSI disk support
Now I did build in other things like input device and USB support and etc. but the above is a pretty complete list (I can supply my kernel config file if necessary). I did not include any SCSI controller drivers or SCSI emulation support in the IDE section. I also did not include Network block device support or Minix fs support. Since I did not include Minix fs support I altered the initrd file to be gzipped ext2 instead of Minix. (created a ext2 fs on a file and then tar'ed all the stuff over from the uncompressed and loopback mounted Minix initrd file). Since I have what I hope to be a 2.6 kernel that should not require any modules I removed all of the SuSE9-X86_64 2.4 kernel module files from the initrd file that was on the original boot.iso
I have quite a bit of Linux experience (since 1993) and I am running other 2.6.0-test kernel on my other x386 system but this is the first Opteron system I have goofed with.
During kernel bootup it does say
RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) read only Freeing unused kernel memory: 168k freed Kernel panic: No init found. Try passing init= option to the kerme.
The mkisofs command I am using to build my test boot.iso images is:
mkisofs -b boot/loader/isolinux.bin -c boot/loader/isolinux.cat -no-emul-boot\ -boot-load-size 4 -boot-info-table -l -R -r -o boot_k26sminitrd.iso newboot/
I tried passing init=/linuxrc or init=linuxrc but I still get the "No init found" I also tried a 2.4 kernel built which a friend in CZ built with a sata_sil driver in it but that did not find the 3114 device. I did not have a "No init found" problem with that kernel however.
Can anyone see from my above list of drivers I compiled into the kernel anything obvious I would be missing? Or any other problems that might cause this?
BTW, I originally was working with the default 4Mb ramdisk_size as compiled into the 2.6 kernel but then I thought I might try bumping that up to 64Mb since that is what is needed for the rescue image (I have been trying to boot to either that or the standard install choice). Still same thing.
I tried also booting this kernel and initrd via PXE across the network but I had no luck with that either. ARGH!!! -- Steven A. DuChene linux-clusters@mindspring.com sduchene@mindspring.com
-- Check the List-Unsubscribe header to unsubscribe For additional commands, email: suse-amd64-help@suse.com