[opensuse] camera does not show up as disk on 13.2
Using SuSE-12.3 this camera is detected and I can get to it via the file manager. On 13.2 it is detected but when I open it with the file manager I get an error. Dolphin shows "USB PTP Class Camera" but when I click on it I get "Unknown error code 150 I/O; Problem Please send a full bug report at http://bugs.kde.org" The camera is a Sony Cybershot This is the dmesg output when I plug in a normal USB stick. Jun 21 08:18:39 harley kernel: usb 2-4: new high-speed USB device number 10 using ehci-pci Jun 21 08:18:39 harley kernel: usb 2-4: New USB device found, idVendor=154b, idProduct=6545 Jun 21 08:18:39 harley kernel: usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 21 08:18:39 harley kernel: usb 2-4: Product: USB 2.0 FD Jun 21 08:18:39 harley kernel: usb 2-4: Manufacturer: PNY Jun 21 08:18:39 harley kernel: usb 2-4: SerialNumber: 4527700EC5D36C9A Jun 21 08:18:39 harley kernel: usb-storage 2-4:1.0: USB Mass Storage device detected Jun 21 08:18:39 harley kernel: scsi host23: usb-storage 2-4:1.0 Jun 21 08:18:38 harley mtp-probe: checking bus 2, device 10: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-4" Jun 21 08:18:38 harley mtp-probe: bus: 2, device: 10 was not an MTP device Jun 21 08:18:40 harley kernel: scsi 23:0:0:0: Direct-Access PNY USB 2.0 FD 8.02 PQ: 0 ANSI: 0 CCS Jun 21 08:18:40 harley kernel: sd 23:0:0:0: Attached scsi generic sg9 type 0 Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] 15695871 512-byte logical blocks: (8.03 GB/7.48 GiB) Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Write Protect is off Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Mode Sense: 45 00 00 08 Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] No Caching mode page found Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Assuming drive cache: write through Jun 21 08:18:40 harley kernel: sdh: sdh1 Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Attached SCSI removable disk This is the dmesg output when I plugin the camera. Jun 21 08:20:15 harley kernel: usb 2-3: new high-speed USB device number 11 using ehci-pci Jun 21 08:20:15 harley kernel: usb 2-3: New USB device found, idVendor=054c, idProduct=02f9 Jun 21 08:20:15 harley kernel: usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 21 08:20:15 harley kernel: usb 2-3: Product: Sony DSC Jun 21 08:20:15 harley kernel: usb 2-3: Manufacturer: Sony Jun 21 08:20:15 harley kernel: usb 2-3: SerialNumber: D27B7068E623 Jun 21 08:20:15 harley kernel: usb-storage 2-3:1.0: USB Mass Storage device detected Jun 21 08:20:15 harley kernel: scsi host24: usb-storage 2-3:1.0 Jun 21 08:20:14 harley mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-3" Jun 21 08:20:14 harley mtp-probe: bus: 2, device: 11 was not an MTP device This is the lsusb output when both the USB stick and the camera are connected. Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 0424:2504 Standard Microsystems Corp. USB 2.0 Hub Bus 002 Device 010: ID 154b:6545 PNY FD Device Bus 002 Device 011: ID 054c:02f9 Sony Corp. DSC-H9 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 002: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub This is the lsscsi -g output with both plugged in. [0:0:0:0] disk ATA ST3160215AS D /dev/sda /dev/sg0 [1:0:0:0] disk ATA ST3500320NS SN06 /dev/sdb /dev/sg1 [2:0:0:0] disk ATA ST3320620AS K /dev/sdc /dev/sg2 [3:0:0:0] disk ATA ST32000641AS CC13 /dev/sdd /dev/sg3 [6:0:0:0] cd/dvd HL-DT-ST BD-RE BH14NS40 1.00 /dev/sr0 /dev/sg4 [13:0:0:0] process Marvell 91xx Config 1.01 - /dev/sg5 [16:0:0:0] disk ATA ST3120023A 3.31 /dev/sde /dev/sg6 [17:0:0:0] disk ATA ST3320620AS K /dev/sdf /dev/sg7 [17:0:1:0] disk ATA ST3250318AS CC37 /dev/sdg /dev/sg8 [23:0:0:0] disk PNY USB 2.0 FD 8.02 /dev/sdh /dev/sg9 What does one have to do to get to my camera as a storage device? Thanks Mark -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 06/21/2015 08:30 AM, Mark Hounschell wrote:
What does one have to do to get to my camera as a storage device?
As far as I'm concerned its BAH HUMBUG! on this. My camera worked in 11.x but not on any 12.x or 13.x So I ended up getting a card-to-usb adaptor and taking the card out of the camera to do the uploads. That being said, the high end Kingston cards work OK. Many other cards don't, aren't recognized, even though the kernel sees the insertion and read the card data. It seems the database tables have shrunk or have had entries removed or the udev runes have been simplified or truncated. I'm sure the developers have a justification for this, but why, when it used to work, what's the problem? -- A: Yes. > Q: Are you sure? >> A: Because it reverses the logical flow of conversation. >>> Q: Why is top posting frowned upon? -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA256 On 2015-06-21 15:05, Anton Aylward wrote:
Many other cards don't, aren't recognized, even though the kernel sees the insertion and read the card data.
Erase the card with dd, partition and format it fresh (with the same FAT flavour). Apparently some cards have a partition table that make Linux tools fail. You notice this when the device node for the partition does not appear. - -- Cheers / Saludos, Carlos E. R. (from 13.1 x86_64 "Bottle" (Minas Tirith)) -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iF4EAREIAAYFAlWGz3gACgkQja8UbcUWM1x/NQEAksOAo68L779GPcDOlsvyliWl Su6/T8SbER3O8bIbRpIA/3Z3OifHvrADDqf+Tqb4LxFQaaeW9URwTTOmzLQfycVx =jdlY -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 06/21/2015 10:51 AM, Carlos E. R. wrote:
On 2015-06-21 15:05, Anton Aylward wrote:
Many other cards don't, aren't recognized, even though the kernel sees the insertion and read the card data.
Erase the card with dd, partition and format it fresh (with the same FAT flavour). Apparently some cards have a partition table that make Linux tools fail.
I don't think you understand.
You notice this when the device node for the partition does not appear.
Yes, I can understand that when there is sdb rather than sdb: sdb1 That latter case, yes there is the partition /dev/sdb1 But if there isn't anthing like that when the card is inserted, just soeting like this: [532830.469042] usb 4-2: new full-speed USB device number 31 using uhci_hcd [532830.730045] usb 1-4: new high-speed USB device number 64 using ehci-pci [532830.845233] usb 1-4: New USB device found, idVendor=14cd, idProduct=125c [532830.845240] usb 1-4: New USB device strings: Mfr=1, Product=3, SerialNumber=2 [532830.845244] usb 1-4: Product: Mass Storage Device [532830.845247] usb 1-4: Manufacturer: Generic [532830.845250] usb 1-4: SerialNumber: 125C20100726 [532830.845654] usb-storage 1-4:1.0: USB Mass Storage device detected [532830.845822] scsi host39: usb-storage 1-4:1.0 [532832.838305] scsi 39:0:0:0: Direct-Access Mass Storage Device PQ: 0 ANSI: 0 CCS [532832.838640] sd 39:0:0:0: Attached scsi generic sg3 type 0 [532832.842643] sd 39:0:0:0: [sdb] Attached SCSI removable disk And that's all! And I get # dd if=/dev/urandom of=/dev/sdb dd: failed to open ‘/dev/sdb’: No medium found # fdisk /dev/sdb fdisk: cannot open /dev/sdb: No medium found Following that I puled the card [533161.786511] usb 1-4: USB disconnect, device number 64 Some cards simply re not recognized. idVendor=14cd, idProduct=125c I'm not alone asking this for that type of card: http://unix.stackexchange.com/questions/134497/why-isnt-sda1-showing-up-in-d... As you can see, he ended up making a device node manually. On my system that would be minor 16 and 17 Surely there should be a udev rule that does that! See also https://forums.opensuse.org/showthread.php/487975-MicroSD-question which is similar, but I don't have the over-voltage and I don't have anything on the 'fdisk'. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 2015-06-21 17:21, Anton Aylward wrote:
And that's all!
And I get
# dd if=/dev/urandom of=/dev/sdb dd: failed to open ‘/dev/sdb’: No medium found
Oh. That's bad :-( (note: no need to randomize, zeros are very good. Use /dev/zero)
I'm not alone asking this for that type of card: http://unix.stackexchange.com/questions/134497/why-isnt-sda1-showing-up-in-d...
As you can see, he ended up making a device node manually. On my system that would be minor 16 and 17 Surely there should be a udev rule that does that!
There was another thread or more on the openSUSE forums. I recommended creating the device node manually, but they did not. I don't remember why, or how the issue was finally solved - I'm trying a grep to locate the post. Yes, udev creates the node, but something triggers it. If that something (I don't know what) doesn't happen, then udev doesn't do its job, either. -- Cheers / Saludos, Carlos E. R. (from 13.1 x86_64 "Bottle" at Telcontar)
On 2015-06-21 19:42, Carlos E. R. wrote:
There was another thread or more on the openSUSE forums. I recommended creating the device node manually, but they did not. I don't remember why, or how the issue was finally solved - I'm trying a grep to locate the post.
Found it: View this thread: <http://forums.opensuse.org/showthread.php?t=506076> It turn out that the culprit in that case was the usb adapter. -- Cheers / Saludos, Carlos E. R. (from 13.1 x86_64 "Bottle" at Telcontar)
On 06/21/2015 01:58 PM, Carlos E. R. wrote:
On 2015-06-21 19:42, Carlos E. R. wrote:
There was another thread or more on the openSUSE forums. I recommended creating the device node manually, but they did not. I don't remember why, or how the issue was finally solved - I'm trying a grep to locate the post.
Found it: View this thread: <http://forums.opensuse.org/showthread.php?t=506076>
It turn out that the culprit in that case was the usb adapter.
Yes I agree when you say
The device appearing or not should be independent of the filesystem inside, or being able to mount or not.
But I don't think its the adaptor. The reason for this is that if I put a 128 MEGABYTE chip in there it all works. But when I try a 32 GIGABYTE chip it doesn't So the adaptor work .... to a point I'm not sure its a 32G problem. I don't have other 32G _chips_. I do have 32G USB sticks and they work. It _might_ be a *limit* of the adaptor. I'll see about getting some other 32G chips to try. Or perhaps some other carrier/adaptor combinations. -- A: Yes. > Q: Are you sure? >> A: Because it reverses the logical flow of conversation. >>> Q: Why is top posting frowned upon? -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello, On Sun, 21 Jun 2015, Mark Hounschell wrote:
Using SuSE-12.3 this camera is detected and I can get to it via the file manager. On 13.2 it is detected but when I open it with the file manager I get an error. Dolphin shows "USB PTP Class Camera" but when I click on it I get "Unknown error code 150 I/O; Problem Please send a full bug report at http://bugs.kde.org"
The camera is a Sony Cybershot
This is the dmesg output when I plugin the camera.
Jun 21 08:20:15 harley kernel: usb 2-3: new high-speed USB device number 11 using ehci-pci Jun 21 08:20:15 harley kernel: usb 2-3: New USB device found, idVendor=054c, idProduct=02f9 Jun 21 08:20:15 harley kernel: usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 21 08:20:15 harley kernel: usb 2-3: Product: Sony DSC Jun 21 08:20:15 harley kernel: usb 2-3: Manufacturer: Sony Jun 21 08:20:15 harley kernel: usb 2-3: SerialNumber: D27B7068E623 Jun 21 08:20:15 harley kernel: usb-storage 2-3:1.0: USB Mass Storage device detected Jun 21 08:20:15 harley kernel: scsi host24: usb-storage 2-3:1.0 Jun 21 08:20:14 harley mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-3" Jun 21 08:20:14 harley mtp-probe: bus: 2, device: 11 was not an MTP device
If you are interested what's going on under the hood you can increase the scsi verbosity which should show something about why the partition(s) are not recognized. There is a sg3_utils package which provide the scsi_logging_level command. The command allows different logging levels to be increased/lowered. I would start with TIMEOUT and ERROR. These things usualy happen if the port is damaged (worn-out) or there is not enough power on it. Also ensure that the cable which is used is good. Regards, I. Petrov -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) Comment: Signed by Topal iQIcBAEBAgAGBQJVhwYWAAoJEH8sJoKRFRU59wsP/R5zV+RsU5uqupp2EaoI6q7g 1fPKp130w/bGJ32/nHxwLCwAObq0Q2G1P1S3Xiq1PF7J+F+9DkFS8yAtbPT3+pc4 DuDyKUH1FraOzr1+JuOXBFD9BZoiDawXqsxbFjdOaaqdDaXujbbCTdDdunmhBtTV E3kwf2emD2sX9Kooaw7bz4qJZBnbUekROJT8c2rHVL3jBIroddO/aZieBBVA2v5L FWq5Cw35ACx4FcwGU1GZGkBPVI+NsR9NeY2kaX+X/jrMiY/9EtnCHI1z7QIRmovM 1lEHwPMenJGSAVwEzo+U07T8RnkTQ3i9+YnoiyXg515DY9Lc9YyunB4MhAIC6hlm 2J4pu11ubfTPNSMbW/frJG5miTH0JmgTk7AnkqCgsUIxuhYeLFril3bZMrhyqO18 Lc+PHmbXhpI1byxUf7Xa4GoqzlavEPuW4NjeyflTyg72uu//NdtDSq+b4SNerl/a gU+czeg+lOmmM07rrwj81duOxukUYhDfTCExqRfmmk8RskBudH5rgUJiMLr4Lw8N H7+nCZKk5Zo2szvnY4P0Y6UnO4fW5pWaiO6/LnEjLktlWEst921GJ+/KGytS8omg KWwqoV69Yd5HtWsbO+SACDGx8YNjXZrWkLrEM/Izi8fwMr0CISYQ8RmZxoq+Rr7C 9fnrlPU6wuH2YeCdXVZL =3YTD -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 2015-06-21 20:44, I. Petrov wrote:
If you are interested what's going on under the hood you can increase the scsi verbosity which should show something about why the partition(s) are not recognized. There is a sg3_utils package which provide the scsi_logging_level command. The command allows different logging levels to be increased/lowered. I would start with TIMEOUT and ERROR. These things usualy happen if the port is damaged (worn-out) or there is not enough power on it. Also ensure that the cable which is used is good.
That's interesting to know, thanks. -- Cheers / Saludos, Carlos E. R. (from 13.1 x86_64 "Bottle" at Telcontar)
On 06/21/2015 08:30 AM, Mark Hounschell wrote:
Using SuSE-12.3 this camera is detected and I can get to it via the file manager. On 13.2 it is detected but when I open it with the file manager I get an error. Dolphin shows "USB PTP Class Camera" but when I click on it I get "Unknown error code 150 I/O; Problem Please send a full bug report at http://bugs.kde.org"
The camera is a Sony Cybershot
This is the dmesg output when I plug in a normal USB stick.
Jun 21 08:18:39 harley kernel: usb 2-4: new high-speed USB device number 10 using ehci-pci Jun 21 08:18:39 harley kernel: usb 2-4: New USB device found, idVendor=154b, idProduct=6545 Jun 21 08:18:39 harley kernel: usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 21 08:18:39 harley kernel: usb 2-4: Product: USB 2.0 FD Jun 21 08:18:39 harley kernel: usb 2-4: Manufacturer: PNY Jun 21 08:18:39 harley kernel: usb 2-4: SerialNumber: 4527700EC5D36C9A Jun 21 08:18:39 harley kernel: usb-storage 2-4:1.0: USB Mass Storage device detected Jun 21 08:18:39 harley kernel: scsi host23: usb-storage 2-4:1.0 Jun 21 08:18:38 harley mtp-probe: checking bus 2, device 10: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-4" Jun 21 08:18:38 harley mtp-probe: bus: 2, device: 10 was not an MTP device Jun 21 08:18:40 harley kernel: scsi 23:0:0:0: Direct-Access PNY USB 2.0 FD 8.02 PQ: 0 ANSI: 0 CCS Jun 21 08:18:40 harley kernel: sd 23:0:0:0: Attached scsi generic sg9 type 0 Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] 15695871 512-byte logical blocks: (8.03 GB/7.48 GiB) Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Write Protect is off Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Mode Sense: 45 00 00 08 Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] No Caching mode page found Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Assuming drive cache: write through Jun 21 08:18:40 harley kernel: sdh: sdh1 Jun 21 08:18:40 harley kernel: sd 23:0:0:0: [sdh] Attached SCSI removable disk
This is the dmesg output when I plugin the camera.
Jun 21 08:20:15 harley kernel: usb 2-3: new high-speed USB device number 11 using ehci-pci Jun 21 08:20:15 harley kernel: usb 2-3: New USB device found, idVendor=054c, idProduct=02f9 Jun 21 08:20:15 harley kernel: usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 21 08:20:15 harley kernel: usb 2-3: Product: Sony DSC Jun 21 08:20:15 harley kernel: usb 2-3: Manufacturer: Sony Jun 21 08:20:15 harley kernel: usb 2-3: SerialNumber: D27B7068E623 Jun 21 08:20:15 harley kernel: usb-storage 2-3:1.0: USB Mass Storage device detected Jun 21 08:20:15 harley kernel: scsi host24: usb-storage 2-3:1.0 Jun 21 08:20:14 harley mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-3" Jun 21 08:20:14 harley mtp-probe: bus: 2, device: 11 was not an MTP device
This is the lsusb output when both the USB stick and the camera are connected.
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 0424:2504 Standard Microsystems Corp. USB 2.0 Hub Bus 002 Device 010: ID 154b:6545 PNY FD Device Bus 002 Device 011: ID 054c:02f9 Sony Corp. DSC-H9 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 002: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
This is the lsscsi -g output with both plugged in.
[0:0:0:0] disk ATA ST3160215AS D /dev/sda /dev/sg0 [1:0:0:0] disk ATA ST3500320NS SN06 /dev/sdb /dev/sg1 [2:0:0:0] disk ATA ST3320620AS K /dev/sdc /dev/sg2 [3:0:0:0] disk ATA ST32000641AS CC13 /dev/sdd /dev/sg3 [6:0:0:0] cd/dvd HL-DT-ST BD-RE BH14NS40 1.00 /dev/sr0 /dev/sg4 [13:0:0:0] process Marvell 91xx Config 1.01 - /dev/sg5 [16:0:0:0] disk ATA ST3120023A 3.31 /dev/sde /dev/sg6 [17:0:0:0] disk ATA ST3320620AS K /dev/sdf /dev/sg7 [17:0:1:0] disk ATA ST3250318AS CC37 /dev/sdg /dev/sg8 [23:0:0:0] disk PNY USB 2.0 FD 8.02 /dev/sdh /dev/sg9
What does one have to do to get to my camera as a storage device?
In runlevel 3 everything works fine. I plug it in and I get a /dev/sd# and I can manually mount it every time. I actually have another 13.2 system at work where this all actually works fine? Why is KDE insisting on this being a PTP Class camera. Why does the kernel not give me a /dev/sd# in run level 5? Mark -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA256 On 2015-06-28 14:33, Mark Hounschell wrote:
Jun 21 08:20:15 harley kernel: usb-storage 2-3:1.0: USB Mass Storage device detected Jun 21 08:20:15 harley kernel: scsi host24: usb-storage 2-3:1.0 Jun 21 08:20:14 harley mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-3" Jun 21 08:20:14 harley mtp-probe: bus: 2, device: 11 was not an MTP device
...
In runlevel 3 everything works fine. I plug it in and I get a /dev/sd# and I can manually mount it every time. I actually have another 13.2 system at work where this all actually works fine? Why is KDE insisting on this being a PTP Class camera. Why does the kernel not give me a /dev/sd# in run level 5?
Maybe mtp-probe switches is :-? Wild wild guess. - -- Cheers / Saludos, Carlos E. R. (from 13.1 x86_64 "Bottle" (Minas Tirith)) -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iF4EAREIAAYFAlWP810ACgkQja8UbcUWM1xvDgD/WJ9rZz0gyyG7zlY2BO5AEXNS c+TbUTW75klBX0gNk5cA/3J3bPRnUDC5xXrCIPZOHKwISpuP80057/BcoMmbp2dO =GERd -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 06/28/2015 09:15 AM, Carlos E. R. wrote:
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA256
On 2015-06-28 14:33, Mark Hounschell wrote:
Jun 21 08:20:15 harley kernel: usb-storage 2-3:1.0: USB Mass Storage device detected Jun 21 08:20:15 harley kernel: scsi host24: usb-storage 2-3:1.0 Jun 21 08:20:14 harley mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-3" Jun 21 08:20:14 harley mtp-probe: bus: 2, device: 11 was not an MTP device
...
In runlevel 3 everything works fine. I plug it in and I get a /dev/sd# and I can manually mount it every time. I actually have another 13.2 system at work where this all actually works fine? Why is KDE insisting on this being a PTP Class camera. Why does the kernel not give me a /dev/sd# in run level 5?
Maybe mtp-probe switches is :-? Wild wild guess.
There was an mtp-probe bug that causes this same symptom. That was fixed some time ago. I've actually deleted the libmtp package to verify it wasn't that. It's not mtp-probe. mark -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
participants (4)
-
Anton Aylward -
Carlos E. R. -
I. Petrov -
Mark Hounschell