How can I tell my system to run at 1280x0124 with H-64 and V-60? Right now I'm running 1280x1024 H-60.4 and V-57 and it doesn't work as well. Tom -- Tom Nielsen Neuro Logic Systems 805.389.5435 x18 www.neuro-logic.com
On Monday 05 May 2003 06:48 pm, Tom Nielsen wrote:
How can I tell my system to run at 1280x0124 with H-64 and V-60?
Right now I'm running 1280x1024 H-60.4 and V-57 and it doesn't work as well.
Tom
Tom, You can use the Graphics Card and Monitor setup part of YaST to manually enter in the H and V values for your LCD screen. Monitors->Properties->Frequencies HTH, Mike
On Tue, 2003-05-06 at 05:32, Tom Nielsen wrote:
Tried that. No workie. I set it to the requirements above and it over wrote them....some how.
Are you running 8.2? Try running "xrandr" and see which options are available to you. If a better refresh rate is available, you can set it with a command like xrandr -r 64 but check first which values are settable by running "xrandr" without any parameters
On Mon, 2003-05-05 at 19:48, Michael Sacco wrote:
On Monday 05 May 2003 06:48 pm, Tom Nielsen wrote:
How can I tell my system to run at 1280x0124 with H-64 and V-60?
Right now I'm running 1280x1024 H-60.4 and V-57 and it doesn't work as well.
Tom
Tom,
You can use the Graphics Card and Monitor setup part of YaST to manually enter in the H and V values for your LCD screen.
Monitors->Properties->Frequencies
HTH, Mike
Tried that. No workie. I set it to the requirements above and it over wrote them....some how. t
On Mon, 2003-05-05 at 20:30, Anders Johansson wrote:
On Tue, 2003-05-06 at 05:32, Tom Nielsen wrote:
Tried that. No workie. I set it to the requirements above and it over wrote them....some how.
Are you running 8.2? Try running "xrandr" and see which options are available to you. If a better refresh rate is available, you can set it with a command like
xrandr -r 64
but check first which values are settable by running "xrandr" without any parameters
I ran it but it says my monitor can only do 62Hz at 1280x1024. I know it can do up to 75. BTW, is this similar to an fbconfig command on a UNIX/Sun box? I can do a fbconfig -setres 1280x1024x70 and it will just take it. Thanks, Tom
Tom, On Tuesday 06 May 2003 4:57 am, Tom Nielsen wrote:
On Mon, 2003-05-05 at 20:30, Anders Johansson wrote:
On Tue, 2003-05-06 at 05:32, Tom Nielsen wrote:
Tried that. No workie. I set it to the requirements above and it over wrote them....some how.
Are you running 8.2? Try running "xrandr" and see which options are available to you. If a better refresh rate is available, you can set it with a command like
xrandr -r 64
but check first which values are settable by running "xrandr" without any parameters
I ran it but it says my monitor can only do 62Hz at 1280x1024. I know it can do up to 75.
BTW, is this similar to an fbconfig command on a UNIX/Sun box? I can do a fbconfig -setres 1280x1024x70 and it will just take it.
Thanks, Tom
Dunno if it helps but I had a problem with my CRT monitor's EDID which lied about the monitor's capabilities. Solution was to add an option to ignore EDID to the XF86Config Device section as follows: Section "Device" BoardName "GeForce4 MX 420" BusID "1:0:0" Driver "nvidia" Identifier "Device[0]" VendorName "NVidia" Option "IgnoreEDID" "True" Option "NvAgp" "1" EndSection I was then able to set the mode to 1600x1200 that the monitor is capable of. Dunno if LCD panels have this option. Geoff Horn
participants (5)
-
Anders Johansson -
Geoff Horn -
Michael Sacco -
Tom Nielsen -
Tom Nielsen