Oops, I don't have my machine in front of me so I was cuting and pasting. It should be something like this: Host: scsi0 Channel: 00 Id: 02 Lun: 00 DVD Drive Host: scsi0 Channel: 00 Id: 03 Lun: 00 CD Drive Host: scsi1 Channel: 00 Id: 01 Lun: 00 CD Writer Host: scsi2 Channel: 00 Id: 06 Lun: 00 Zip Drive Host: scsi2 Channel: 00 Id: 07 Lun: 00 Scanner. I did check the Ids and terminations and all are OK. As I said originally, this worked OK in 6.4. RiKD

-----Original Message----- From: nevada [mailto:phthor@isat.com] Sent: 26 October 2000 15:36 To: suse-linux-e@suse.com Subject: Re: [SLE] Urgent: Problems with Scanner in 7.0

Dunphy Richard-rdunph01 wrote:

...

My SCSI cable is fine on both ends. I use the pass-through to the Zip drive and this works perfectly.

I am using sg4 because of where it is in my system. First I load the ncr538xx module for my DVD and CD drives (sg0 and sg1 respectively). Then I load the ide-scsi for my cd-writer (sg2) and finally load the aha152x module for my ISA SCSI card for the Zip and scanner (sg3 and sg4).

I have tried unloading both ide-scsi and ncr538xx and using sg0 as the scanner (reloading the aha152x module with the Zip drive turned off) but the same thing happens.

doing cat /proc/scsi/scsi basically shows:

Host: scsi0 Channel: 00 Id: 01 Lun: 00 DVD Drive Host: scsi0 Channel: 00 Id: 01 Lun: 00 CD Drive Host: scsi1 Channel: 00 Id: 01 Lun: 00 CD Writer Host: scsi2 Channel: 00 Id: 05 Lun: 00 Zip Drive Host: scsi2 Channel: 00 Id: 05 Lun: 00 Scanner.

RikD

...

-----Original Message----- From: Jerry L Kreps [mailto:jerrykreps@jlkreps.net] Sent: 26 October 2000 12:04 To: Dunphy Richard-rdunph01; SuSE Mailing List Subject: Re: [SLE] Urgent: Problems with Scanner in 7.0

I upgraded to SuSE 7.0 by reformting all my HDs with ReisferFS (which is wonderful!) and doing an install from scratch. I went through the scanner setup on YaST and my Mustek, driven from an ncr53c8xx, like yours, works nicely.

Is your scsi cable seated properly on both ends? I am wondering why you are using sg4? My /dev show the following: crw-rw-rw- 1 root disk 21, 9 Jul 29 07:48 /dev/sg9 lrwxrwxrwx 1 root disk 3 Oct 9 14:49 /dev/sga -> sg0 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgb -> sg1 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgc -> sg2 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgd -> sg3 lrwxrwxrwx 1 root disk 3 Oct 15 12:21 /dev/scanner -> sg0

My /proc/scsi/scsi show:

jerry@JLKreps:~ > cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 06 Lun: 00 Vendor: MUSTEK Model: MFC-06000CZ Rev: 1.02 Type: Scanner ANSI SCSI revision: 01 CCS Host: scsi1 Channel: 00 Id: 06 Lun: 00 Vendor: IOMEGA Model: ZIP 100 Rev: D.09 Type: Direct-Access ANSI SCSI revision: 02

My scsi has scsi0 (sg0) connected to my scanner. What does yours show?

JLK

On Thursday 26 October 2000 03:41, Dunphy Richard-rdunph01 wrote:

...

Hi,

After upgrading to SuSE 7.0 I can't get my Microtek E3 SCSI scanner to work. This worked perfectly in 6.4

My SCSI setup is as follows: host 1: ncr53c8xx (irq 3) ID1 -> Toshiba DVD ID2 -> Toshiba CD host 2: ide-scsi ID1 -> Cyberdrive CD-RW host 3: aha152x (irq 11) ID5 -> Zip 100 Plus ID6 -> Microtek E3 Scanner

Everything is detected fine on booting, and integrating the scanner with YAST works.

Running xsane or xscanimage (as root) shows the scanner on /dev/scanner and /dev/sg4 ok. But when I try to either acquire a preview, or even just scan in an image I get an IO Error message, something like "Error, unexpected IO response!".

I need to scan in some images and do some work for Satuarday so I need to resolve this pretty quickly.

Anyone have any ideas on what's gone wrong? Am I missing something in the install of sane?

Any ideas would be greatly appreciated. RikD.

Looks like to me your have three devices with the same id number, DVD, CD and CD writer. Each should be assigned it's own id number, eq DVD-1, CD-2, CD writer-3. Same with the zip drive-4 and the scanner-5.

Also make sure your termination is correct.

Nevada

-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq