Intel 82562EZ NIC not working with SuSE 9.3

4 Sep 2005

      Hello,

I've got an onboard Intel 82562EZ network card that I'm having trouble with 
on SuSE 9.3. It shows up in Yast2 and I can configure it as 
10.62.56.252/255.255.255.0 http://10.62.56.252/255.255.255.0. However when 
I try and ping another computer on the 10.62.56.x network all I get is:

"From 10.62.56.252 http://10.62.56.252: icmp_seq=3 Destination Host 
Unreachable"

If I move the 10.62.56.x network to another network card everything works as 
expected. I've looked up this card and everything I've found says SuSE 
supports this model.

IFCONFIG Display:
------------------------------------------
eth0 Link encap:Ethernet HWaddr 00:02:A5:47:3E:13 
inet addr:192.168.66.252 http://192.168.66.252
Bcast:192.168.255.255http://192.168.255.255Mask:
255.255.0.0 http://255.255.0.0
inet6 addr: fe80::202:a5ff:fe47:3e13/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4949686 errors:0 dropped:0 overruns:0 frame:0
TX packets:3321458 errors:36 dropped:0 overruns:0 carrier:36
collisions:0 txqueuelen:1000
RX bytes:1649261618 (1572.8 Mb) TX bytes:2151728935 (2052.0 Mb)

eth1 Link encap:Ethernet HWaddr 00:0F:FE:30:DF:A6 
inet addr:10.62.56.252 http://10.62.56.252
Bcast:10.62.56.255http://10.62.56.255Mask:
255.255.255.0 http://255.255.255.0
inet6 addr: fe80::20f:feff:fe30:dfa6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

eth2 Link encap:Ethernet HWaddr 00:20:78:11:89:42 
inet addr:xx.xx.xx.xx Bcast:xx.xx.xx.xx
Mask:255.255.255.128http://255.255.255.128
inet6 addr: fe80::220:78ff:fe11:8942/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6012160 errors:0 dropped:0 overruns:0 frame:0
TX packets:4042775 errors:141 dropped:0 overruns:0 carrier:282
collisions:0 txqueuelen:1000
RX bytes:1966893694 (1875.7 Mb) TX bytes:904246790 (862.3 Mb)
Interrupt:5 Base address:0xb800

eth3 Link encap:Ethernet HWaddr 00:04:5A:46:50:94 
inet addr:172.16.72.2 http://172.16.72.2
Bcast:172.16.255.255http://172.16.255.255Mask:
255.255.0.0 http://255.255.0.0
inet6 addr: fe80::204:5aff:fe46:5094/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3427218 errors:0 dropped:0 overruns:0 frame:0
TX packets:3670839 errors:49 dropped:0 overruns:0 carrier:98
collisions:0 txqueuelen:1000
RX bytes:1797204430 (1713.9 Mb) TX bytes:2743849420 (2616.7 Mb)
Interrupt:5 Base address:0xb400

lo Link encap:Local Loopback 
inet addr:127.0.0.1 http://127.0.0.1 Mask:255.0.0.0 http://255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:514670 errors:0 dropped:0 overruns:0 frame:0
TX packets:514670 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1126379514 (1074.1 Mb) TX bytes:1126379514 (1074.1 Mb)

NOTE: I removed my public ip address!

ETHTOOLS Display:
------------------------------------------
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Current message level: 0x00000007 (7)
Link detected: yes

LSPCI Displays:
------------------------------------------
0000:00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM 
Controller/Host-Hub Interface (rev 02)
0000:00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated 
Graphics Controller (rev 02)
0000:00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
UHCI Controller #1 (rev 02)
0000:00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
UHCI Controller #2 (rev 02)
0000:00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
UHCI #3 (rev 02)
0000:00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB 
UHCI Controller #4 (rev 02)
0000:00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 
EHCI Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
0000:00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC 
Interface Bridge (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE 
Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus 
Controller (rev 02)
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER 
(ICH5/ICH5R) AC'97 Audio Controller (rev 02)
0000:01:00.0 Ethernet controller: Linksys NC100 Network Everywhere Fast 
Ethernet 10/100 (rev 11)
0000:01:01.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 
100] (rev 08)
0000:01:02.0 Ethernet controller: Linksys NC100 Network Everywhere Fast 
Ethernet 10/100 (rev 11)
0000:01:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet 
Controller (rev 02)

Any idea what would cause this and how to fix it?

Thanks

MePHiTiC

tags

participants (1)