On 02/11/04 04:41 PM, Nicholas DeClario wrote:

Hey guys. I was wondering if anyone can point me in the right direction for some documentation exclusive to SuSE 9.x or SLES9 for ethernet bonding. I found many resources on bonding in general but nothing specific to SuSE.

IIRC someone posted a howto to the list in May/June for 9.1, that should put you in the right direction. Regards, Ben

Hi, Bond can be configured by following the procedure mentioned in the location. But I am seeing each time when I start the network, during enslaving it results in "Illegal operation: bond is not up message." I can see bond configuring properly. Why are these messages? Thanks, Anil -----Original Message----- From: Ben Higginbottom [mailto:b.higginbottom@trinityhigh.com] Sent: Wednesday, November 03, 2004 3:54 PM To: Nicholas DeClario Cc: suse-linux-e@suse.com Subject: Re: [SLE] Bonding in SuSE SLES9 On 03/11/04 09:56 AM, Ben Higginbottom wrote:

On 02/11/04 04:41 PM, Nicholas DeClario wrote:

...

Hey guys. I was wondering if anyone can point me in the right direction for some documentation exclusive to SuSE 9.x or SLES9 for ethernet bonding. I found many resources on bonding in general but nothing specific to SuSE.

IIRC someone posted a howto to the list in May/June for 9.1, that should put you in the right direction.

Dirk Laurenz kindly pointed out the correct date and time of the post in question, but I dont think it made it to the list The archived post can be found here: http://lists.suse.com/archive/suse-linux-e/2004-May/4175.html Regards, Ben -- Check the headers for your unsubscription address For additional commands send e-mail to suse-linux-e-help@suse.com Also check the archives at http://lists.suse.com Please read the FAQs: suse-linux-e-faq@suse.com Confidentiality Notice The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain confidential or privileged information. If you are not the intended recipient, please notify the sender at Wipro or Mailadmin@wipro.com immediately and destroy all copies of this message and any attachments.

Hi, No If I load the bond and configure manually, I don't see this message. If my bond is not loaded and I call /etc/init.d/network start, I face this problem. Thanks, Anil -----Original Message----- From: Ben Higginbottom [mailto:b.higginbottom@trinityhigh.com] Sent: Wednesday, November 03, 2004 6:23 PM To: Anil V Gangur Cc: suse-linux-e@suse.com Subject: RE: [SLE] Bonding in SuSE SLES9 On 03/11/04 12:40 PM, Anil V Gangur wrote:

Hi,

Bond can be configured by following the procedure mentioned in the location.

But I am seeing each time when I start the network, during enslaving

it

results in "Illegal operation: bond is not up message."

I can see bond configuring properly. Why are these messages?

Never seen that before, does strace provide anything useful when you start network manually? Regards, Ben Confidentiality Notice The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain confidential or privileged information. If you are not the intended recipient, please notify the sender at Wipro or Mailadmin@wipro.com immediately and destroy all copies of this message and any attachments.

On Wed, 2004-11-03 at 04:40, Anil V Gangur wrote:

Hi,

Bond can be configured by following the procedure mentioned in the location.

But I am seeing each time when I start the network, during enslaving it results in "Illegal operation: bond is not up message."

I can see bond configuring properly. Why are these messages?

Thanks, Anil

I had this occur originally as well because I was loading the bonding driver manually. Did you start this out fresh or did you try to correct your previous attempts? Brad Dameron SeaTab Software www.seatab.com