[SLE] Soundblaster problems

10 Mar 2000

      Hello,

I have a Soundblaster AWE64 and I am trying to run it with suse 6.3. 
Aparently suse is trying to use irq 7 instead of 5 as the card is set to
do.
I get choppy sound and the console is telling me that there is an irq
conflict with irq 7.
I have run pnpdump > isapnp.conf and selected the ?correct?
configuration for the card in isapnp.conf.
I do not know what to do next?  HELP!!

Here is the isapnp.conf file.

Thanks in advance for your help.

Craig

# $Id: pnpdump.c,v 1.19 1999/10/16 15:17:17 fox Exp $
# Release isapnptools-1.19
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0273
# Board 1 has serial identifier f2 0d 1d 29 b7 c1 00 8c 0e

# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier f2 0d 1d 29 b7 c1 00 8c 0e)
# Vendor Id CTL00c1, Serial Number 220015031, checksum 0xF2.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative SB AWE64 PnP<--
#
# Logical device id CTL0042
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if r
equired
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00c1/220015031 (LD 0
#     ANSI string -->Audio<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
 (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
 (DMA 0 (CHANNEL 1))
#       Next DMA channel 5.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
 (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 1 bytes
#             Number of IO addresses required: 16
 (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
 (IO 1 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
 (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority functional
#       IRQ 5, 7, 9 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 16 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0394
#             IO base alignment 4 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#     End dependent functions
 (NAME "CTL00c1/220015031[0]{Audio               }")
 (ACT Y)
))
#
# Logical device id CTL7002
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if r
equired
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00c1/220015031 (LD 1
#     Compatible device id PNPb02f
#     ANSI string -->Game<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x0200
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0200
#             Maximum IO base address 0x0208
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))

#     End dependent functions
 (NAME "CTL00c1/220015031[1]{Game                }")
# (ACT Y)
))
#
# Logical device id CTL0022
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3c
#     Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be
changed if r
equired
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00c1/220015031 (LD 2
#     ANSI string -->WaveTable<--

# Multiple choice time, choose one only !

#             Maximum IO base address 0x0620
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0620))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0620
#             Maximum IO base address 0x0680
#             IO base alignment 32 bytes
#             Number of IO addresses required: 4
# (IO 0 (SIZE 4) (BASE 0x0620))

#     End dependent functions
 (NAME "CTL00c1/220015031[2]{WaveTable           }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

-- 
To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com
For additional commands send e-mail to suse-linux-e-help@suse.com             
Also check the FAQ at http://www.suse.com/Support/Doku/FAQ/

csharp2a＠earthlink.net

herman＠knief.net

tags

participants (2)