[opensuse] System Showing Only 4GB RAM
Hi, openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu. Sysinfo:/ OS: Linux 3.1.0-1.2-desktop x86_64 Current user: muktware@linux-mpdu System: openSUSE 12.1 (x86_64) KDE: 4.7.2 (4.7.2) "release 5" Total memory (RAM): 3.9 GiB Free memory: 192.2 MiB (+ 730.4 MiB Caches) Free swap: 3.9 GiB Swapnil -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Wednesday 04 January 2012, Swapnil Bhartiya wrote:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system.
Does your motherboard support 8GB and does it recognize all DIMMs? What says dmidecode? cu, Rudi -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Does your motherboard support 8GB and does it recognize all DIMMs?
Yes. MB is Asus P7p55D-E LX and supports extra RAM 4 x DIMM, Max. 16GB, DDR3 2200(O.C.)/1600/1333/1066 MHz Non-ECC, Un-buffered Memory
What says dmidecode?
http://www.susepaste.org/946139 Swapnil -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Wednesday 04 January 2012, Swapnil Bhartiya wrote:
Does your motherboard support 8GB and does it recognize all DIMMs?
Yes. MB is Asus P7p55D-E LX and supports extra RAM
4 x DIMM, Max. 16GB, DDR3 2200(O.C.)/1600/1333/1066 MHz Non-ECC, Un-buffered Memory
Look at the QVL list http://support.asus.com/QVL.aspx?SLanguage=en&p=1&s=32&m=P7P55D-E%20LX&os=&hashedid=DfyAB26HiDpiiu8f There are certain restrictions regarding CPU, RAM clock and different vendors.
What says dmidecode?
I wonder this block: Handle 0x0034, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 4 cu, Rudi -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Swapnil Bhartiya said the following on 01/04/2012 06:06 AM:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64
Try running the "-PAE" version of the kernel. Read the kernel notes as to why you should do that if you have more than 4G of memory. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Wed, Jan 4, 2012 at 12:30, Anton Aylward <opensuse@antonaylward.com> wrote:
Swapnil Bhartiya said the following on 01/04/2012 06:06 AM:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64
Try running the "-PAE" version of the kernel. Read the kernel notes as to why you should do that if you have more than 4G of memory.
Ummmmm... why would he want to run a 32-bit PAE kernel? He's already running a 64-bit kernel. You only need PAE on 32 bit kernels to get beyond the 4GB memory addressing limitation... this limitation (at 4GB) doesn't exist on 64 bit kernels. C. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
04.01.2012 15:46, C пишет:
On Wed, Jan 4, 2012 at 12:30, Anton Aylward<opensuse@antonaylward.com> wrote:
Swapnil Bhartiya said the following on 01/04/2012 06:06 AM:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64 Try running the "-PAE" version of the kernel. Read the kernel notes as to why you should do that if you have more than 4G of memory. Ummmmm... why would he want to run a 32-bit PAE kernel? He's already running a 64-bit kernel. You only need PAE on 32 bit kernels to get beyond the 4GB memory addressing limitation... this limitation (at 4GB) doesn't exist on 64 bit kernels.
C. I think 64bit kernel is required when you use applications which eats more 2 Gb of memory. I think using of pae kernel saves memory, because you run 32bit applications which require less memory than 64bit ones. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/04/2012 10:15 PM, Dmitry A. Ashkadov wrote:
04.01.2012 15:46, C пишет:
On Wed, Jan 4, 2012 at 12:30, Anton Aylward<opensuse@antonaylward.com> wrote:
Swapnil Bhartiya said the following on 01/04/2012 06:06 AM:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64 Try running the "-PAE" version of the kernel. Read the kernel notes as to why you should do that if you have more than 4G of memory. Ummmmm... why would he want to run a 32-bit PAE kernel? He's already running a 64-bit kernel. You only need PAE on 32 bit kernels to get beyond the 4GB memory addressing limitation... this limitation (at 4GB) doesn't exist on 64 bit kernels.
C. I think 64bit kernel is required when you use applications which eats more 2 Gb of memory. I think using of pae kernel saves memory, because you run 32bit applications which require less memory than 64bit ones.
I remember that my system was detecting and using the all of 8GB ram. The last time I checked was when I wrote about Ubuntu. I found a screenshot from that time and it says 8GB (I remember I added more RAM so that I can test more distros from within VB.) http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system-... It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN. Swapnil -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system -specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in. Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in). If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket. -- Regards, Rajko -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 01:24 AM, Rajko M. wrote:
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system -specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in.
Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in).
If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket.
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS. Should I RMA? I bought it in August? Fortunately I had another MB P7P55D-E and tried it detected full 8GB RAM. Swapnil -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Thursday, January 05, 2012 09:06:27 PM Swapnil Bhartiya wrote:
I don't know if its a hardware issue or BIOS. Should I RMA?
BIOS is part of the motherboard and if it worked before with the same version it should work now. The only thing I would try is to load optimal settings, and check how much memory is recognized, then safe settings and check again. If neither works then call vendor and check with them. You have to call them anyway before you send board back. Have ready all steps that you described in previous email, so that you can repeat when they ask. -- Regards, Rajko -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 06/01/12 14:06, Swapnil Bhartiya wrote:
On 01/06/2012 01:24 AM, Rajko M. wrote:
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system
-specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in.
Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in).
If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket.
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS. Should I RMA? I bought it in August?
Fortunately I had another MB P7P55D-E and tried it detected full 8GB RAM.
Check the manual for your motherboard and check into which slots the RAM has to go to be fully recognised; also check whether the RAM used is matched pairs or unmatched singles (also if they have 16 chips onboard or more - eg, a mobo I am using will not accept sticks if they have more than 16 chips on board). I had a Gigabyte motherboard which accepted 2GB of RAM, and had 4 slots for the RAM. At the time I bought 2X512MB matched DDRs and then later bought 2 single, unmatched 512MB sticks. The 2 matched sticks had to go into slots 1 and 3 to work as dual-channel RAM but when I added the single sticks nothing worked. Reason was that to get the full 2GB I had to have 4 single, unmatched, sticks. I didn't know this until I read the manual :-( . BC -- What religion were Adam and Eve? -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 05:54 AM, Basil Chupin wrote:
On 06/01/12 14:06, Swapnil Bhartiya wrote:
On 01/06/2012 01:24 AM, Rajko M. wrote:
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system
-specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in.
Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in).
If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket.
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS. Should I RMA? I bought it in August?
Fortunately I had another MB P7P55D-E and tried it detected full 8GB RAM.
Check the manual for your motherboard and check into which slots the RAM has to go to be fully recognised; also check whether the RAM used is matched pairs or unmatched singles (also if they have 16 chips onboard or more - eg, a mobo I am using will not accept sticks if they have more than 16 chips on board).
I had a Gigabyte motherboard which accepted 2GB of RAM, and had 4 slots for the RAM. At the time I bought 2X512MB matched DDRs and then later bought 2 single, unmatched 512MB sticks. The 2 matched sticks had to go into slots 1 and 3 to work as dual-channel RAM but when I added the single sticks nothing worked. Reason was that to get the full 2GB I had to have 4 single, unmatched, sticks. I didn't know this until I read the manual :-( .
Yes, the RAMs were working fine. I was using the full 8GB of it, but something went wrong lately. Swapnil -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Thu, Jan 5, 2012 at 11:57 PM, Swapnil Bhartiya <swapnil.bhartiya@gmail.com> wrote:
On 01/06/2012 05:54 AM, Basil Chupin wrote:
On 06/01/12 14:06, Swapnil Bhartiya wrote:
On 01/06/2012 01:24 AM, Rajko M. wrote:
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system
-specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in.
Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in).
If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket.
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS. Should I RMA? I bought it in August?
Fortunately I had another MB P7P55D-E and tried it detected full 8GB RAM.
Check the manual for your motherboard and check into which slots the RAM has to go to be fully recognised; also check whether the RAM used is matched pairs or unmatched singles (also if they have 16 chips onboard or more - eg, a mobo I am using will not accept sticks if they have more than 16 chips on board).
I had a Gigabyte motherboard which accepted 2GB of RAM, and had 4 slots for the RAM. At the time I bought 2X512MB matched DDRs and then later bought 2 single, unmatched 512MB sticks. The 2 matched sticks had to go into slots 1 and 3 to work as dual-channel RAM but when I added the single sticks nothing worked. Reason was that to get the full 2GB I had to have 4 single, unmatched, sticks. I didn't know this until I read the manual :-( .
Yes, the RAMs were working fine. I was using the full 8GB of it, but something went wrong lately.
Swapnil
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
I might have missed, but can you do this for me. uname -a I want to see what version you have installed. Chuck -- Terror PUP a.k.a Chuck "PUP" Payne (678) 636-9678 ----------------------------------------- Discover it! Enjoy it! Share it! openSUSE Linux. ----------------------------------------- openSUSE -- en.opensuse.org/User:Terrorpup openSUSE Ambassador/openSUSE Member skype,twiiter,identica,friendfeed -- terrorpup freenode(irc) --terrorpup/lupinstein Register Linux Userid: 155363 Have you tried SUSE Studio? Need to create a Live CD, an app you want to package and distribute , or create your own linux distro. Give SUSE Studio a try. www.susestudio.com. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 06:01 AM, Chuck Payne wrote:
uname -a Linux linux-f1zk 3.1.0-1.2-desktop #1 SMP PREEMPT Thu Nov 3 14:45:45 UTC 2011 (187dde0) x86_64 x86_64 x86_64 GNU/Linux
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 05:54 AM, Basil Chupin wrote:
On 06/01/12 14:06, Swapnil Bhartiya wrote:
On 01/06/2012 01:24 AM, Rajko M. wrote:
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system
-specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in.
Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in).
If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket.
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS. Should I RMA? I bought it in August?
Fortunately I had another MB P7P55D-E and tried it detected full 8GB RAM.
Check the manual for your motherboard and check into which slots the RAM has to go to be fully recognised; also check whether the RAM used is matched pairs or unmatched singles (also if they have 16 chips onboard or more - eg, a mobo I am using will not accept sticks if they have more than 16 chips on board).
/snip/
Yes, the RAMs were working fine. I was using the full 8GB of it, but something went wrong lately.
Swapnil I fairly recently had reason to pull a memory stick (to find out what its type was) and I put it back-- unknowingly, it was not seated properly, and I theorized later that one of the pins was touching a jack connection that it shouldn't have. The memory stick got hot as blazes, and that slot on
On 1/5/2012 11:57 PM, Swapnil Bhartiya wrote: the MOBO would no longer accept memory. That is, the MOBO was damaged beyond repair. So was the memory stick, of course. It was an expensive lesson: do not work in dim light, and make _sure_ the memory stick is seated properly. (In your case, it may very well be too late, as it was in mine.) --doug -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 07:08 AM, Doug wrote:
On 01/06/2012 05:54 AM, Basil Chupin wrote:
On 06/01/12 14:06, Swapnil Bhartiya wrote:
On 01/06/2012 01:24 AM, Rajko M. wrote:
On Thursday, January 05, 2012 05:38:39 PM Swapnil Bhartiya wrote: ...
http://www.muktware.com/sites/default/files/images/manual/ubuntu1110/system
-specs.jpeg
It's only recently I noticed only 4GB RAM. The only physical change that I made was added a CoolMaster FAN.
That gives idea where to look. Pull memory sticks out and back in.
Whenever you work something inside the computer and something fails, first thing is to check contacts and connectors by simply re-seat them (pull out completely and then push back in).
If that doesn't help pull memory sticks out and inspect visually contacts and sockets for dust, as it can happen that reseating pushed some dust in a socket.
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS. Should I RMA? I bought it in August?
Fortunately I had another MB P7P55D-E and tried it detected full 8GB RAM.
Check the manual for your motherboard and check into which slots the RAM has to go to be fully recognised; also check whether the RAM used is matched pairs or unmatched singles (also if they have 16 chips onboard or more - eg, a mobo I am using will not accept sticks if they have more than 16 chips on board).
/snip/
Yes, the RAMs were working fine. I was using the full 8GB of it, but something went wrong lately.
Swapnil I fairly recently had reason to pull a memory stick (to find out what its type was) and I put it back-- unknowingly, it was not seated properly, and I theorized later that one of the pins was touching a jack connection that it shouldn't have. The memory stick got hot as blazes, and that slot on
On 1/5/2012 11:57 PM, Swapnil Bhartiya wrote: the MOBO would no longer accept memory. That is, the MOBO was damaged beyond repair. So was the memory stick, of course. It was an expensive lesson: do not work in dim light, and make _sure_ the memory stick is seated properly. (In your case, it may very well be too late, as it was in mine.)
Thanks for Advice. Luckily I RMAed my Mobo last year and bought a new one as back-up. I was using the new one which supposedly started showing issues. So this one is going for RMA now. Swapnil
--doug
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On Friday 06 January 2012, Swapnil Bhartiya wrote:
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS.
The QVL list I've posted in my other email says that only 2 of these 4 slots are working if RAM is running on 1600MHz. There are also issues with 2.66GHz CPUs. Have you checked your BIOS settings? cu, Rudi -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 07:28 AM, Ruediger Meier wrote:
On Friday 06 January 2012, Swapnil Bhartiya wrote:
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS.
The QVL list I've posted in my other email says that only 2 of these 4 slots are working if RAM is running on 1600MHz. There are also issues with 2.66GHz CPUs. Have you checked your BIOS settings?
As I said before that the System was using the full 8GB RAM before. From BIOS the frequency was automated which was set at 1333 GHz. The system suddenly stopped detecting the extra RAM. When I removed 2 sticks and left only 4GB then it detected only 2GB. So, something went wrong.
cu, Rudi
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 01/06/2012 07:28 AM, Ruediger Meier wrote:
On Friday 06 January 2012, Swapnil Bhartiya wrote:
Seems like MB is the culprit. I tried resetting RAM and CPU but no success then I removed 2 sticks leaving on 4GB on board but then the system detected only one. I tried one and failed to detect RAM from 2 slot. I don't know if its a hardware issue or BIOS.
The QVL list I've posted in my other email says that only 2 of these 4 slots are working if RAM is running on 1600MHz. There are also issues with 2.66GHz CPUs. Have you checked your BIOS settings?
It was an hardware issue. The DIMM slots were not working. Swapnil
cu, Rudi
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Anton Aylward wrote:
Try running the "-PAE" version of the kernel. Read the kernel notes as to why you should do that if you have more than 4G of memory.
Isn't PAE for 32 bit CPUs? https://en.wikipedia.org/wiki/Physical_Address_Extension -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 1/4/2012 6:30 AM, Anton Aylward wrote:
Swapnil Bhartiya said the following on 01/04/2012 06:06 AM:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64
Try running the "-PAE" version of the kernel. Read the kernel notes as to why you should do that if you have more than 4G of memory.
x86_64 obviates -pae Verify the motherboard/bios actually sees more than 4G. Sounds like a hardware/firmware compatibility thing not a linux kernel thing. -- bkw -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 04/01/2012 12:06, Swapnil Bhartiya a écrit :
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system
try memtest (any openSUSE dvd, at boot time) jdd -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
On 04/01/12 08:06, Swapnil Bhartiya wrote:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64 Current user: muktware@linux-mpdu System: openSUSE 12.1 (x86_64) KDE: 4.7.2 (4.7.2) "release 5"
Total memory (RAM): 3.9 GiB Free memory: 192.2 MiB (+ 730.4 MiB Caches) Free swap: 3.9 GiB
Swapnil
What does dmesg -k says ? does the BIOS have any special option that could be related to this problem ? did you tried using "optimized setup defaults" or similar ? -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Swapnil Bhartiya [04.01.2012 12:06]:
Hi,
openSUSE is showing only 3.9GB of RAM whereas I have 8GB installed on the system. Sometimes FF takes upto 800MG which slows the browser. I have installed 64bit version which should show full RAM. It shows OK under Ubuntu.
Sysinfo:/
OS: Linux 3.1.0-1.2-desktop x86_64 Current user: muktware@linux-mpdu System: openSUSE 12.1 (x86_64) KDE: 4.7.2 (4.7.2) "release 5"
Total memory (RAM): 3.9 GiB Free memory: 192.2 MiB (+ 730.4 MiB Caches) Free swap: 3.9 GiB
Swapnil
Hi Swapnil, it might be not related to openSUSE 12.1. Here I'm sitting in front of a PC with 8 GiB: # free total used free shared buffers cached Mem: 8191512 7346868 844644 0 588236 3911212 -/+ buffers/cache: 2847420 5344092 Swap: 16777212 2116 16775096 So, no problem here. Mainboard: Asus M4N78 PRO. Sysinfo: Kernel: Linux 3.1.0-1.2-desktop x86_64 Distribution: openSUSE 12.1 (x86_64) KDE: 4.7.4 (4.7.4) "release 11" At home, the setup recognizes 8 GiB RAM too, but the install doesn't work. After struggling with the disks, I cant start memtest because it does not fit into memory (says grub or memtest). Plus, grub shows only 4 GiB after this failed attempt. It's a Gigabyte mainboard, should be the same as Asus, but isn't. So the problem may be your hardware :-( Regards, Werner -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
participants (14)
-
Anton Aylward -
Basil Chupin -
Brian K. White -
C -
Chuck Payne -
Cristian Rodríguez -
Dmitry A. Ashkadov -
Doug -
James Knott -
jdd -
Rajko M. -
Ruediger Meier -
Swapnil Bhartiya -
Werner Flamme