[opensuse] usb 3 ubs
Hello, I have some problem to manage usb3. I use a pci-express card with 4 usb3 connectors. for some weeks, no problems. I had an usb3 hard drive connected. This disk was seen at boot (or at connect) and notified by the applet. now it is no more notifyed (since approx a week) config, update or other problem? During this period I tested some USB 3 hubs (4 ports) with overall bad results. Two hubs from two different vendors may be during the tests something did corrupt the previous install? the problepm with the hubs was an unreliable connection. The drives are seen or not, depending of... I don't know. the two hubs have a 5V power. so... is this install not normal? is the card seen as a hub and the system do not like two cascading hubs? here dmesg: I remove the HDD: [ 2428.271735] usb 2-1.1: USB disconnect, device number 3 I insert it again in an other port: [39408.168703] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [39408.179813] usb 4-3: Parent hub missing LPM exit latency info. Power management will be impacted. [39408.180640] usb 4-3: New USB device found, idVendor=0bc2, idProduct=5031 [39408.180646] usb 4-3: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [39408.180650] usb 4-3: Product: FreeAgent GoFlex [39408.180654] usb 4-3: Manufacturer: Seagate [39408.180657] usb 4-3: SerialNumber: NA0Q8ZXF [39408.181485] scsi11 : usb-storage 4-3:1.0 [39409.187567] scsi 11:0:0:0: Direct-Access Seagate FreeAgent GoFlex 0219 PQ: 0 ANSI: 5 [39409.187926] sd 11:0:0:0: Attached scsi generic sg4 type 0 [39409.188347] sd 11:0:0:0: [sdd] 1953525167 512-byte logical blocks: (1.00 TB/931 GiB) [39409.189115] sd 11:0:0:0: [sdd] Write Protect is off [39409.189120] sd 11:0:0:0: [sdd] Mode Sense: 4f 00 00 00 [39409.190687] sd 11:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [39409.226559] sdd: sdd1 [39409.228490] sd 11:0:0:0: [sdd] Attached SCSI disk I can mount it, but of course as root /dev/sdd1 on /mnt type fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096) the same disk reacts perfectly when connected on usb2 any idea? thanks jdd -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Changed something in BIOS? Especially I've seen IOMMU, if disabled to break it 2013/10/14 jdd <jdd@dodin.org>:
Hello,
I have some problem to manage usb3.
I use a pci-express card with 4 usb3 connectors.
for some weeks, no problems. I had an usb3 hard drive connected. This disk was seen at boot (or at connect) and notified by the applet.
now it is no more notifyed (since approx a week)
config, update or other problem?
During this period I tested some USB 3 hubs (4 ports) with overall bad results. Two hubs from two different vendors
may be during the tests something did corrupt the previous install?
the problepm with the hubs was an unreliable connection. The drives are seen or not, depending of... I don't know. the two hubs have a 5V power.
so... is this install not normal? is the card seen as a hub and the system do not like two cascading hubs?
here dmesg:
I remove the HDD: [ 2428.271735] usb 2-1.1: USB disconnect, device number 3
I insert it again in an other port: [39408.168703] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [39408.179813] usb 4-3: Parent hub missing LPM exit latency info. Power management will be impacted. [39408.180640] usb 4-3: New USB device found, idVendor=0bc2, idProduct=5031 [39408.180646] usb 4-3: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [39408.180650] usb 4-3: Product: FreeAgent GoFlex [39408.180654] usb 4-3: Manufacturer: Seagate [39408.180657] usb 4-3: SerialNumber: NA0Q8ZXF [39408.181485] scsi11 : usb-storage 4-3:1.0 [39409.187567] scsi 11:0:0:0: Direct-Access Seagate FreeAgent GoFlex 0219 PQ: 0 ANSI: 5 [39409.187926] sd 11:0:0:0: Attached scsi generic sg4 type 0 [39409.188347] sd 11:0:0:0: [sdd] 1953525167 512-byte logical blocks: (1.00 TB/931 GiB) [39409.189115] sd 11:0:0:0: [sdd] Write Protect is off [39409.189120] sd 11:0:0:0: [sdd] Mode Sense: 4f 00 00 00 [39409.190687] sd 11:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [39409.226559] sdd: sdd1 [39409.228490] sd 11:0:0:0: [sdd] Attached SCSI disk
I can mount it, but of course as root
/dev/sdd1 on /mnt type fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096)
the same disk reacts perfectly when connected on usb2
any idea?
thanks jdd
-- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 15/10/2013 09:22, Damian Ivanov a écrit :
Changed something in BIOS? Especially I've seen IOMMU, if disabled to break it
not that I know, but could be a bad setup. What is IOMMU? http://en.wikipedia.org/wiki/IOMMU in what part of the BIOS? thanks jdd -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
It should be in features, it's a feature for virtualization, but if it is disabled I had problems with usb 2 and 3: https://www.google.bg/search?q=iommu+usb+linux&oq=iommu+usb+linux&aqs=chrome..69i57j0.4158j0j7&sourceid=chrome&espv=210&es_sm=122&ie=UTF-8 2013/10/15 jdd <jdd@dodin.org>:
Le 15/10/2013 09:22, Damian Ivanov a écrit :
Changed something in BIOS? Especially I've seen IOMMU, if disabled to break it
not that I know, but could be a bad setup. What is IOMMU?
http://en.wikipedia.org/wiki/IOMMU
in what part of the BIOS?
thanks jdd
-- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 15/10/2013 09:31, Damian Ivanov a écrit :
It should be in features, it's a feature for virtualization, but if it is disabled I had problems with usb 2 and 3: https://www.google.bg/search?q=iommu+usb+linux&oq=iommu+usb+linux&aqs=chrome..69i57j0.4158j0j7&sourceid=chrome&espv=210&es_sm=122&ie=UTF-8
no problem for three years with usb2, but I will look at this immédiately, thanks jdd -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 15/10/2013 09:35, jdd a écrit :
Le 15/10/2013 09:31, Damian Ivanov a écrit :
It should be in features, it's a feature for virtualization, but if it is disabled I had problems with usb 2 and 3: https://www.google.bg/search?q=iommu+usb+linux&oq=iommu+usb+linux&aqs=chrome..69i57j0.4158j0j7&sourceid=chrome&espv=210&es_sm=122&ie=UTF-8
no problem for three years with usb2, but I will look at this immédiately, thanks
jdd
I see nothing related to IOMMU. My mobo is this one: http://h10025.www1.hp.com/ewfrf/wc/document?cc=fr&lc=fr&dlc=fr&tmp_geoLoc=true&docname=c02049273 dmesg usb3 related (remember usb3 is not on the mobo but on additional card): [ 73.860874] usb 4-3: reset SuperSpeed USB device number 2 using xhci_hcd [ 73.872402] usb 4-3: Parent hub missing LPM exit latency info. Power management will be impacted. [ 73.872643] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801a63cdcc0 [ 73.872649] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801a63cdd00 lines 1017-1057/1057 (END) probably this one http://cgi.ebay.fr/PCI-E-PCI-Express-Vers-4-Port-USB-3-0-USB-Hub-Carte-Controleur-Adaptateur-5Gbps-/181111979555?pt=FR_JG_Informatique_Perpheriques_Hubs&hash=item2a2b1d7e23 thanks jdd -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Since you said it worked for a while I would try if it still works with live usb from which you installed openSUSE. :) 2013/10/15 jdd <jdd@dodin.org>:
Le 15/10/2013 09:35, jdd a écrit :
Le 15/10/2013 09:31, Damian Ivanov a écrit :
It should be in features, it's a feature for virtualization, but if it is disabled I had problems with usb 2 and 3:
no problem for three years with usb2, but I will look at this immédiately, thanks
jdd
I see nothing related to IOMMU. My mobo is this one:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=fr&lc=fr&dlc=fr&tmp_geoLoc=true&docname=c02049273
dmesg usb3 related (remember usb3 is not on the mobo but on additional card):
[ 73.860874] usb 4-3: reset SuperSpeed USB device number 2 using xhci_hcd [ 73.872402] usb 4-3: Parent hub missing LPM exit latency info. Power management will be impacted. [ 73.872643] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801a63cdcc0 [ 73.872649] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8801a63cdd00 lines 1017-1057/1057 (END)
probably this one
thanks jdd
-- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 15/10/2013 10:41, Damian Ivanov a écrit :
Since you said it worked for a while I would try if it still works with live usb from which you installed openSUSE. :)
good guess... I do not have a 12.3 dvd and this &é"'(-è_ç mobo do not boot usb! but the live demo dvd for 12.2 starts as expected and show the hsb3 disk in the applet so the problem now is narrowed: how to reset the usb3 setup on my real install? some xml magic? thanks jdd -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
I would try first to narrow down, where the problem is, try with another user etc. I am not quite sure if the problem is not in the $USER config what would need to be done. anyone? 2013/10/15 jdd <jdd@dodin.org>:
Le 15/10/2013 10:41, Damian Ivanov a écrit :
Since you said it worked for a while I would try if it still works with live usb from which you installed openSUSE. :)
good guess... I do not have a 12.3 dvd and this &é"'(-è_ç mobo do not boot usb!
but the live demo dvd for 12.2 starts as expected and show the hsb3 disk in the applet
so the problem now is narrowed: how to reset the usb3 setup on my real install? some xml magic?
thanks jdd
-- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
-- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 15/10/2013 11:23, Damian Ivanov a écrit :
I would try first to narrow down, where the problem is, try with another user etc. I am not quite sure if the problem is not in the $USER config what would need to be done. anyone?
yes, I did it be with no change. ps ax (after mounting disk from applet) on usb2 port 5758 ? Ds 0:00 /sbin/mount.ntfs /dev/sdk1 /run/media/jdd/FreeAgent GoFlex Drive -o rw,nodev,nosuid,uid=1000,gid=100,dmask=0077,fmask=0177,uhelper=udisks2 the disk is ntfs (and always was) on the same port, an usb key with openSUSE dvd on it appears in the applet... jdd -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
Le 15/10/2013 11:10, jdd a écrit :
so the problem now is narrowed: how to reset the usb3 setup on my real install? some xml magic?
the usb hub is (lspci -vvnn) 04:00.0 USB controller [0c03]: VIA Technologies, Inc. VL80x xHCI USB 3.0 Controller [1106:3432] (rev 03) (prog-if 30 [XHCI]) Subsystem: VIA Technologies, Inc. VL80x xHCI USB 3.0 Controller [1106:3432] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at fbeff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 41b1 Capabilities: [c4] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <256ns, L1 <16us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <16us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range B, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: xhci_hcd
and the drive is seen (lsusb) Bus 004 Device 002: ID 0bc2:5031 Seagate RSS LLC FreeAgent GoFlex USB 3.0 so may be it's a kde problem?? -- http://www.dodin.org -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org
participants (2)
-
Damian Ivanov -
jdd