I am having trouble getting my Lexar 128MB Jumpdrive Sport USB 2.0 flash key to work under SuSE 8.2. Has anyone had similar problems and found a fix? I made sure that the j-drive was formatted as FAT and that it worked in Windows XP. When I plug it in the system beeps like it finds it and sure enough there is some activity visible via dmesg. output from dmesg: hub.c: new USB device 00:09.2-3, assigned address 2 usb.c: USB device 2 (vend/prod 0x5dc/0xa300) is not claimed by any active driver. Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage scsi1 : SCSI emulation for USB Mass Storage devices Vendor: Generic Model: STORAGE DEVICE Rev: 1.25 Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sda: 256000 512-byte hdwr sectors (131 MB) sda: Write Protect is off sda: sda1 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 USB Mass Storage support registered. --------------------------------------------- I then tried to mount sda1 which is where USB memory devices (digital camera) had mounted before. But I get the following: ~> mount /media/sda1 mount: can't find /media/sda1 in /etc/fstab or /etc/mtab --------------------------------------------- Sure enough if I list the contents of /etc/fstab I get: ~> cat /etc/fstab /dev/hda4 / xfs defaults 1 1 /dev/hda2 /boot ext2 defaults 1 2 /dev/hdb5 /home xfs defaults 1 2 /dev/hdb8 /local xfs defaults 1 2 /dev/hdb6 /usr xfs defaults 1 2 /dev/hdb7 /var xfs defaults 1 2 /dev/hda3 swap swap pri=42 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 proc /proc proc defaults 0 0 usbdevfs /proc/bus/usb usbdevfs noauto 0 0 /dev/cdrecorder /media/cdrecorder auto ro,noauto,user,exec 0 0 /dev/cdrom /media/cdrom auto ro,noauto,user,exec 0 0 /dev/dvd /media/dvd auto ro,noauto,user,exec 0 0 /dev/fd0 /media/floppy auto noauto,user,sync 0 0 /dev/hda1 /windows/C vfat noauto,user 0 0 --------------------------------------------- I thought maybe I should restart hotplug but when I do it just hangs at the usb services: ~ # /etc/init.d/hotplug restart Stopping hotplugging services done Starting hotplugging services [ ieee1394 net pci usb --------------------------------------------- Then the following lines are in dmesg: usb_control/bulk_msg: timeout usb.c: USB disconnect on device 00:09.2-3 address 2 hub.c: new USB device 00:09.2-3, assigned address 3 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 3 usb-storage: host_reset() requested but not implemented scsi: device set offline - command error recover failed: host 1 channel 0 id 0 lun 0 SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6050000 I/O error: dev 08:00, sector 0 usb.c: deregistering driver usb-storage scsi : 1 host left. usbserial.c: USB Serial deregistering driver Generic usb.c: deregistering driver serial uhci.c: USB Universal Host Controller Interface driver v1.1 Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage scsi1 : SCSI emulation for USB Mass Storage devices Vendor: Model: Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sda: 256000 512-byte hdwr sectors (131 MB) sda: sda1 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 3 USB Mass Storage support registered. usb_control/bulk_msg: timeout hub.c: new USB device 00:09.1-1, assigned address 2 scsi2 : SCSI emulation for USB Mass Storage devices Vendor: Model: Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0 SCSI device sdb: 256000 512-byte hdwr sectors (131 MB) sdb: sdb1 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 usb-storage: host_reset() requested but not implemented scsi: device set offline - command error recover failed: host 1 channel 0 id 0 lun 0 SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6050000 I/O error: dev 08:00, sector 0 ----------------------------------------------- Sorry for the long message but I wanted to give as much info as possible. Can anyone help me here? TIA, Darrell Cormier
participants (1)
-
Darrell Cormier