From: Michael Long <michael.long@erols.com> Date: Wed, 6 Dec 2000 08:19:58 -0500 Message-Id: <00120608303200.02749@zues> Subject: Startup scripts Now that my network has been configure using YAST and YAST2 everything works except it is necessary to run YAST2 after a reboot in order for eth0 to get its IP address from the cable modem. Then it is necessary to run rcnetwork and firewall scripts manually to finish configuring the network. How do I get these things to happen when the system boots up? Thanks, Mike
Date: Wed, 6 Dec 2000 07:56:24 -0600 From: Jeffrey Taylor <jeff.taylor@ieee.org> Message-ID: <20001206075624.A1405@elendil.bearhouse.lan> Subject: Re: [SLE] Startup scripts Michael, I am using a cable modem (Road Runner) and none of this is necessary. Can you describe what does not work that makes running YAST after booting necessary? DHCP should start up at boot and get the IP address. If you have a PCMCIA Ethernet interface or something else that takes time to startup there is a delay, DHCLIENT_SLEEP, in /etc/rc.config you can set. HTH Jeffrey Quoting Michael Long <michael.long@erols.com>:
Now that my network has been configure using YAST and YAST2 everything works except it is necessary to run YAST2 after a reboot in order for eth0 to get its IP address from the cable modem. Then it is necessary to run rcnetwork and firewall scripts manually to finish configuring the network. How do I get these things to happen when the system boots up?
Thanks, Mike
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
From: Michael Long <michael.long@erols.com> Date: Wed, 6 Dec 2000 13:30:09 -0500 Message-Id: <00120613355800.00352@zues> Subject: Re: [SLE] Startup scripts My cable provider is Charter. I changed the DHCLIENT_SLEEP parameter to 120 and it made no difference. When the system first starts up... rcnetwork status eth0 Link encap:Ethernet HWaddr 00:40:95:30:4A:62 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:10 Base address:0xc800 eth1 Link encap:Ethernet HWaddr 00:40:95:30:4A:63 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:5 Base address:0xcc00 firewall status Checking the status of the Firewall: Chain input (policy ACCEPT: 0 packets, 0 bytes): Chain forward (policy ACCEPT: 0 packets, 0 bytes): Chain output (policy ACCEPT: 0 packets, 0 bytes): It appears as if the network and firewall scripts are not run at startup. Mike On Wed, 06 Dec 2000, Jeffrey Taylor wrote:
Michael, I am using a cable modem (Road Runner) and none of this is necessary. Can you describe what does not work that makes running YAST after booting necessary? DHCP should start up at boot and get the IP address. If you have a PCMCIA Ethernet interface or something else that takes time to startup there is a delay, DHCLIENT_SLEEP, in /etc/rc.config you can set.
HTH Jeffrey
Quoting Michael Long <michael.long@erols.com>:
Now that my network has been configure using YAST and YAST2 everything works except it is necessary to run YAST2 after a reboot in order for eth0 to get its IP address from the cable modem. Then it is necessary to run rcnetwork and firewall scripts manually to finish configuring the network. How do I get these things to happen when the system boots up?
Thanks, Mike
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
-- Michael Long michael.long@erols.com Phone: 508-393-2653
participants (2)
-
jeff.taylor＠ieee.org -
michael.long＠erols.com