Hi guys I have downloaded Live DVD for SLP9.2 from ftp.suse.com. After burning the iso on dvd it works on the computer on which iso was downloaded n burned, but id doesnt work on other computers. what could be the problem. kanak
news wrote:
Hi guys
I have downloaded Live DVD for SLP9.2 from ftp.suse.com. After burning the iso on dvd it works on the computer on which iso was downloaded n burned, but id doesnt work on other computers.
what could be the problem.
kanak
An out of spec drive perhaps. With a previous burner, I couldn't get CD's to boot on the drive they were created on, so I had to do all my burning on the other box. Regards Sid. -- Sid Boyce .... Hamradio G3VBV and keen Flyer =====LINUX ONLY USED HERE=====
Right, I have similiar expiriences! Regards Martin Sid Boyce wrote:
news wrote:
Hi guys
I have downloaded Live DVD for SLP9.2 from ftp.suse.com. After burning the iso on dvd it works on the computer on which iso was downloaded n burned, but id doesnt work on other computers.
what could be the problem.
kanak
An out of spec drive perhaps. With a previous burner, I couldn't get CD's to boot on the drive they were created on, so I had to do all my burning on the other box. Regards Sid.
Hi everybody, I have a problem with SuSEfirewall2 in SuSE 8.2 I can't seem to get solved. I have a dialin server I want to run squid and the firewall in parallel on, so users can surf with squid as proxy and cache, and connect to the internet with my box as a simple forwarding router on all other protocols. When I disable SuSEfirewall2, squid works as intended, but, of course, no IP forwarding is done. When I start up SuSEfirewall2, I get connection timeout errors from squid, but the forwarding works as I expect. I figure that the connections to port 3128 (where I have squid listening) are forwarded somewhere else? I have a Samba server on my box as well, this is not affected but works with and without the firewall. My relevant settings in /etc/sysconfig/SuSEfirewall2 (hope I caught all relevant ones): FW_QUICKMODE="no" FW_DEV_EXT="ippp0" FW_DEV_INT="eth0 eth1" FW_ROUTE="yes" FW_MASQUERADE="yes" FW_MASQ_DEV="$FW_DEV_EXT" FW_MASQ_NETS="0/0" FW_SERVICES_EXT_TCP="139 3128 http ssh" FW_SERVICE_AUTODETECT="yes" FW_SERVICE_DNS="no" FW_SERVICE_SQUID="yes" FW_SERVICE_SAMBA="yes" FW_KERNEL_SECURITY="yes" FW_REDIRECT="" # i tried "192.168.0.0/16,0/0,tcp,80,3128" as well, without success Thanks for any help Helge
helge preuss wrote:
I have a problem with SuSEfirewall2 in SuSE 8.2 I can't seem to get solved. I have a dialin server I want to run squid and the firewall in parallel on, so users can surf with squid as proxy and cache, and connect to the internet with my box as a simple forwarding router on all other protocols. When I disable SuSEfirewall2, squid works as intended, but, of course, no IP forwarding is done. When I start up SuSEfirewall2, I get connection timeout errors from squid, but the forwarding works as I expect. I figure that the connections to port 3128 (where I have squid listening) are forwarded somewhere else? I have a Samba server on my box as well, this is not affected but works with and without the firewall. My relevant settings in /etc/sysconfig/SuSEfirewall2 (hope I caught all relevant ones):
FW_QUICKMODE="no" FW_DEV_EXT="ippp0" FW_DEV_INT="eth0 eth1"
This doesn't look correct. Where is the ppp0 for the dial-in interface?
FW_ROUTE="yes" FW_MASQUERADE="yes" FW_MASQ_DEV="$FW_DEV_EXT" FW_MASQ_NETS="0/0" FW_SERVICES_EXT_TCP="139 3128 http ssh"
Are you proxying from outside as well? You would definitely need FW_SERVICES_INT_TCP="3128"
FW_SERVICE_AUTODETECT="yes" FW_SERVICE_DNS="no" FW_SERVICE_SQUID="yes" FW_SERVICE_SAMBA="yes" FW_KERNEL_SECURITY="yes" FW_REDIRECT="" # i tried "192.168.0.0/16,0/0,tcp,80,3128" as well, without success
That might be correct if 1) your subnet is 16, normally this 24 and 2) your dialin interface is configured to get an address in this range and 3) your squid is configured as a transparent proxy. -- Joe Morris New Tribes Mission Email Address: Joe_Morris@ntm.org Registered Linux user 231871
Hi everybody, I have a problem with SuSEfirewall2 in SuSE 8.2 I can't seem to get solved. I have a dialin server I want to run squid and the firewall in parallel on, so users can surf with squid as proxy and cache, and connect to the internet with my box as a simple forwarding router on all other protocols. When I disable SuSEfirewall2, squid works as intended, but, of course, no IP forwarding is done. When I start up SuSEfirewall2, I get connection timeout errors from squid, but the forwarding works as I expect. I figure that the connections to port 3128 (where I have squid listening) are forwarded somewhere else? I have a Samba server on my box as well, this is not affected but works with and without the firewall. My relevant settings in /etc/sysconfig/SuSEfirewall2 (hope I caught all relevant ones): FW_QUICKMODE="no" FW_DEV_EXT="ippp0" FW_DEV_INT="eth0 eth1" FW_ROUTE="yes" FW_MASQUERADE="yes" FW_MASQ_DEV="$FW_DEV_EXT" FW_MASQ_NETS="0/0" FW_SERVICES_EXT_TCP="139 3128 http ssh" FW_SERVICE_AUTODETECT="yes" FW_SERVICE_DNS="no" FW_SERVICE_SQUID="yes" FW_SERVICE_SAMBA="yes" FW_KERNEL_SECURITY="yes" FW_REDIRECT="" # i tried "192.168.0.0/16,0/0,tcp,80,3128" as well, without success Thanks for any help Helge
participants (6)
-
helge preuss -
James Knott -
Joe Morris (NTM) -
Martin Deppe -
news -
Sid Boyce