[SLE] Urgent: Problems with Scanner in 7.0
Hi, After upgrading to SuSE 7.0 I can't get my Microtek E3 SCSI scanner to work. This worked perfectly in 6.4 My SCSI setup is as follows: host 1: ncr53c8xx (irq 3) ID1 -> Toshiba DVD ID2 -> Toshiba CD host 2: ide-scsi ID1 -> Cyberdrive CD-RW host 3: aha152x (irq 11) ID5 -> Zip 100 Plus ID6 -> Microtek E3 Scanner Everything is detected fine on booting, and integrating the scanner with YAST works. Running xsane or xscanimage (as root) shows the scanner on /dev/scanner and /dev/sg4 ok. But when I try to either acquire a preview, or even just scan in an image I get an IO Error message, something like "Error, unexpected IO response!". I need to scan in some images and do some work for Satuarday so I need to resolve this pretty quickly. Anyone have any ideas on what's gone wrong? Am I missing something in the install of sane? Any ideas would be greatly appreciated. RikD. -- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
I upgraded to SuSE 7.0 by reformting all my HDs with ReisferFS (which is wonderful!) and doing an install from scratch. I went through the scanner setup on YaST and my Mustek, driven from an ncr53c8xx, like yours, works nicely. Is your scsi cable seated properly on both ends? I am wondering why you are using sg4? My /dev show the following: crw-rw-rw- 1 root disk 21, 9 Jul 29 07:48 /dev/sg9 lrwxrwxrwx 1 root disk 3 Oct 9 14:49 /dev/sga -> sg0 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgb -> sg1 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgc -> sg2 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgd -> sg3 lrwxrwxrwx 1 root disk 3 Oct 15 12:21 /dev/scanner -> sg0 My /proc/scsi/scsi show: jerry@JLKreps:~ > cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 06 Lun: 00 Vendor: MUSTEK Model: MFC-06000CZ Rev: 1.02 Type: Scanner ANSI SCSI revision: 01 CCS Host: scsi1 Channel: 00 Id: 06 Lun: 00 Vendor: IOMEGA Model: ZIP 100 Rev: D.09 Type: Direct-Access ANSI SCSI revision: 02 My scsi has scsi0 (sg0) connected to my scanner. What does yours show? JLK On Thursday 26 October 2000 03:41, Dunphy Richard-rdunph01 wrote:
Hi,
After upgrading to SuSE 7.0 I can't get my Microtek E3 SCSI scanner to work. This worked perfectly in 6.4
My SCSI setup is as follows: host 1: ncr53c8xx (irq 3) ID1 -> Toshiba DVD ID2 -> Toshiba CD host 2: ide-scsi ID1 -> Cyberdrive CD-RW host 3: aha152x (irq 11) ID5 -> Zip 100 Plus ID6 -> Microtek E3 Scanner
Everything is detected fine on booting, and integrating the scanner with YAST works.
Running xsane or xscanimage (as root) shows the scanner on /dev/scanner and /dev/sg4 ok. But when I try to either acquire a preview, or even just scan in an image I get an IO Error message, something like "Error, unexpected IO response!".
I need to scan in some images and do some work for Satuarday so I need to resolve this pretty quickly.
Anyone have any ideas on what's gone wrong? Am I missing something in the install of sane?
Any ideas would be greatly appreciated. RikD.
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
On Thursday 26 October 2000 06:03, Jerry L Kreps wrote:
I upgraded to SuSE 7.0 by reformting all my HDs with ReisferFS (which is wonderful!) and doing an install from scratch. I went through the scanner setup on YaST and my Mustek, driven from an ncr53c8xx, like yours, works nicely.
Is your scsi cable seated properly on both ends? I am wondering why you are using sg4? My /dev show the following: crw-rw-rw- 1 root disk 21, 9 Jul 29 07:48 /dev/sg9 oops! should be: crw-rw-rw- 1 root disk 21, 9 Jul 29 07:48 /dev/sg0 lrwxrwxrwx 1 root disk 3 Oct 9 14:49 /dev/sga -> sg0 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgb -> sg1 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgc -> sg2 lrwxrwxrwx 1 root root 3 Oct 9 14:49 /dev/sgd -> sg3 lrwxrwxrwx 1 root disk 3 Oct 15 12:21 /dev/scanner -> sg0
My /proc/scsi/scsi show:
jerry@JLKreps:~ > cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 06 Lun: 00 Vendor: MUSTEK Model: MFC-06000CZ Rev: 1.02 Type: Scanner ANSI SCSI revision: 01 CCS Host: scsi1 Channel: 00 Id: 06 Lun: 00 Vendor: IOMEGA Model: ZIP 100 Rev: D.09 Type: Direct-Access ANSI SCSI revision: 02
My scsi has scsi0 (sg0) connected to my scanner. What does yours show?
JLK
On Thursday 26 October 2000 03:41, Dunphy Richard-rdunph01 wrote:
Hi,
After upgrading to SuSE 7.0 I can't get my Microtek E3 SCSI scanner to work. This worked perfectly in 6.4
My SCSI setup is as follows: host 1: ncr53c8xx (irq 3) ID1 -> Toshiba DVD ID2 -> Toshiba CD host 2: ide-scsi ID1 -> Cyberdrive CD-RW host 3: aha152x (irq 11) ID5 -> Zip 100 Plus ID6 -> Microtek E3 Scanner
Everything is detected fine on booting, and integrating the scanner with YAST works.
Running xsane or xscanimage (as root) shows the scanner on /dev/scanner and /dev/sg4 ok. But when I try to either acquire a preview, or even just scan in an image I get an IO Error message, something like "Error, unexpected IO response!".
I need to scan in some images and do some work for Satuarday so I need to resolve this pretty quickly.
Anyone have any ideas on what's gone wrong? Am I missing something in the install of sane?
Any ideas would be greatly appreciated. RikD.
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
participants (2)
-
jerrykreps＠jlkreps.net -
Rik.Dunphy＠motorola.com