On Sunday 15 July 2007 10:21:32 Rajko M. wrote:
On Sunday 15 July 2007 00:26, Bob S wrote:
Hello SuSE people,
Been trying to get my sensors.conf file to report accurately on my system.
.....<snipped many non-pertinent parts>....
It would be good to read http://www.lm-sensors.org/wiki/FAQ section 3. Problems. http://www.lm-sensors.org/wiki/FAQ/Chapter3
Hi Rajko, thanks for trying to help. Sorry for the delay in responding. For some unknown reason this mail has been rejected by the list twice so far. I had to create a new message which will break the threading. Grrrr !!! Anyway, Nothing in the above URL's about these problems. I really hate posting these really long mails for fear of the other members being upset, Maybe we should take this off list.
Short: Sensors will show what you set in sensors.conf, and that can be correct or out of way.
Welllll. not exactly, I made some changes today in sensors.conf and one of the changes is not being honored. To bring you up to date. Today, I just commented out the -12V parameter because the bios doesn't report it and that worked OK. But,,,,,I created a new problem when I removed the comment lines for in0, the Vcore. See that in my latest sensors printout just below: Still have the alarm problem for the 3.3V parameter. EasyStreet:/ # sensors w83627thf-isa-0290 Adapter: ISA adapter VCore: +1.54 V (min = +1.94 V, max = +1.94 V) ALARM +12V: +12.28 V (min = +10.82 V, max = +13.19 V) +3.3V: +0.45 V (min = +3.14 V, max = +3.47 V) ALARM +5V: +5.09 V (min = +4.75 V, max = +5.25 V) V5SB: +5.16 V (min = +4.76 V, max = +5.24 V) VBat: +3.62 V (min = +2.40 V, max = +4.08 V) Sys Fan: 3183 RPM (min = 2800 RPM, div = 2) CPU Fan: 5672 RPM (min = 5487 RPM, div = 2) M/B Temp: +46°C (high = +86°C, hyst = +2°C) sensor = thermistor CPU Temp: +33.5°C (high = +80°C, hyst = +75°C) sensor = diode alarms: beep_enable: Sound alarm enabled EasyStreet:/ #
Write down BIOS reports and post it here.
OK,,Here is what is reported in the bios" CPU 55 degrees C Sys Tmp 45 degrees C CPU Fan 5720 rpm Sys Fan 3185 rpm Vcore =1.54V +5 =5.25V +12 =11.8V +3.3 =3.4V
Also the section of /etc/sensors.conf that is used with your sensor: chip w83627thf-*
OK, Here is sensors.conf: (Mind you I have made changes to this conf file) I uncommented and commented in0 several times and still come up with the crazy min/max levels for Vcore as shown above. chip "w83627thf-*" "w83637hf-*" # Rather than an internal inverting op amp, the 627thf uses standard positive # inputs and the negative voltages are level shifted by a 3.6V reference # (same as 82d/83s). # The math is convoluted, so we hope that your motherboard # uses the recommended resistor values. # Note that in1 (+12V) is the usual in4, and in4 (-12V) is the usual in5. # Data sheet is obviously wrong for in4, the usual formula should work. # No in5 nor in6. # sensors doesn't need the ignore lines but sensord does... ignore in4 (this removed the -12V parameter) ignore in5 ignore in6 label in0 "VCore" label in1 "+12V" label in2 "+3.3V" label in3 "+5V" # label in4 "-12V" label in7 "V5SB" label in8 "VBat" # Mori Hiroyuki reported to need this (P4P800) # compute in0 @/2, @*2 compute in1 ((28/10)+1)*@, @/((28/10)+1) compute in3 ((34/51)+1)*@, @/((34/51)+1) compute in4 (5.14*@)-14.91, (@+14.91)/5.14 compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) # adjust this if your vid is wrong; see doc/vid # set vrm 9.0 # set limits to 5% for the critical voltages # set limits to 10% for the non-critical voltages # set limits to 20% for the battery voltage # if your vid is wrong, you'll need to adjust in0_min and in0_max # set in0_min vid * 0.95 (these two lines were uncommented which caused the new alarm problem. They were commented again and the problem remains) # set in0_max vid * 1.05 # set in1_min 12 * 0.90 # set in1_max 12 * 1.10 # set in2_min 3.3 * 0.95 # set in2_max 3.3 * 1.05 # set in3_min 5.0 * 0.95 # set in3_max 5.0 * 1.05 # set in4_min -12 * 1.10 # set in4_max -12 * 0.90 # set in7_min 5 * 0.95 # set in7_max 5 * 1.05 # set in8_min 3.0 * 0.80 # set in8_max 3.0 * 1.20 # set up sensor types (thermistor is default) # 1 = PII/Celeron Diode; 2 = 3904 transistor; # 3435 = thermistor with Beta = 3435 # If temperature changes very little, try 1 or 2. # set sensor1 1 # set sensor2 2 # set sensor3 3435 label temp1 "M/B Temp" label temp2 "CPU Temp" ignore temp3 # examples for temperature limits # set temp1_over 40 # set temp1_hyst 37 # set temp2_over 52 # set temp2_hyst 47 # set temp3_over 52 # set temp3_hyst 47 label fan1 "Sys Fan" label fan2 "CPU Fan" ignore fan3
What is your motherboard and chipset? What tells lspci -v
EasyStreet:/ # lspci -v 00:00.0 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Subsystem: VIA Technologies, Inc. Unknown device 3282 Flags: bus master, 66MHz, medium devsel, latency 8 Memory at d0000000 (32-bit, prefetchable) [size=128M] Capabilities: [80] AGP version 3.0 Capabilities: [50] Power Management version 2 Capabilities: [60] HyperTransport: Slave or Primary Interface Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration 00:00.1 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Flags: bus master, medium devsel, latency 0 00:00.2 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Flags: bus master, medium devsel, latency 0 00:00.3 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Flags: bus master, medium devsel, latency 0 00:00.4 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Flags: bus master, medium devsel, latency 0 00:00.7 Host bridge: VIA Technologies, Inc. K8T800Pro Host Bridge Flags: bus master, medium devsel, latency 0 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: cde00000-cfefffff Prefetchable memory behind bridge: add00000-cdcfffff Capabilities: [80] Power Management version 2 00:08.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11) Subsystem: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185 Memory at cfff8000 (32-bit, non-prefetchable) [size=16K] I/O ports at d400 [size=256] Expansion ROM at cffc0000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] Vital Product Data 00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) Subsystem: Micro-Star International Co., Ltd. K8T Neo 2 Motherboard Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at ec00 [size=8] I/O ports at e800 [size=4] I/O ports at e400 [size=8] I/O ports at e000 [size=4] I/O ports at dc00 [size=16] I/O ports at d800 [size=256] Capabilities: [c0] Power Management version 2 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard Flags: bus master, medium devsel, latency 32, IRQ 169 I/O ports at fc00 [size=16] Capabilities: [c0] Power Management version 2 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard Flags: bus master, medium devsel, latency 64, IRQ 177 I/O ports at c400 [size=32] Capabilities: [80] Power Management version 2 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard Flags: bus master, medium devsel, latency 64, IRQ 177 I/O ports at c800 [size=32] Capabilities: [80] Power Management version 2 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard Flags: bus master, medium devsel, latency 64, IRQ 177 I/O ports at cc00 [size=32] Capabilities: [80] Power Management version 2 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard Flags: bus master, medium devsel, latency 64, IRQ 177 I/O ports at d000 [size=32] Capabilities: [80] Power Management version 2 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI]) Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard Flags: bus master, medium devsel, latency 64, IRQ 177 Memory at cfff7e00 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60) Subsystem: Micro-Star International Co., Ltd. Unknown device 7023 Flags: medium devsel, IRQ 193 I/O ports at c000 [size=256] Capabilities: [c0] Power Management version 2 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel 01:00.0 VGA compatible controller: nVidia Corporation NV36.2 [GeForce FX 5700] (rev a1) (prog-if 00 [VGA]) Subsystem: ASUSTeK Computer Inc. Unknown device 814f Flags: bus master, 66MHz, medium devsel, latency 248, IRQ 201 Memory at ce000000 (32-bit, non-prefetchable) [size=16M] Memory at b0000000 (32-bit, prefetchable) [size=256M] [virtual] Expansion ROM at cfee0000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Capabilities: [44] AGP version 3.0 EasyStreet:/ # Thanks, Bob S. -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org