I have a computer running Tumbleweed that I'm using as a router. I am using wicked for network management. I have 1 interface (enp5s6) connected to the wan using dhcp. I have 1 interface (enp3s0 bridged br0) connected to the lan with a static ip address. In YaST2 on the routing tab of network settings I have Enable IPv4 & IPv6 Forwarding checked. In Yast2 in the Masquerading section of Firewall, I have Masquerade Networks checked. I have dnsmasq taking care of dns and dhcp. This all works, but I would like to get IPv6 working. I found this guide https://doc.opensuse.org/documentation/leap/reference/html/ book.opensuse.reference/cha.basicnet.html and created the 50-router.conf file. After several reboots of the computer and modem, I'm not getting an IPv6 address assigned to the interface. n1250:~ # ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0 state UP group default qlen 1000 link/ether 50:e5:49:c6:1a:e0 brd ff:ff:ff:ff:ff:ff 3: enp5s6: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN group default qlen 1000 link/ether 00:50:04:22:fd:33 brd ff:ff:ff:ff:ff:ff inet 174.1xx.xxx.xxx/20 brd 255.255.255.255 scope global enp5s6 valid_lft forever preferred_lft forever inet6 fe80::250:4ff:fe22:fd33/64 scope link valid_lft forever preferred_lft forever 5: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 50:e5:49:c6:1a:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.0.50/24 brd 192.168.0.255 scope global br0 valid_lft forever preferred_lft forever inet6 fe80::52e5:49ff:fec6:1ae0/64 scope link valid_lft forever preferred_lft forever I only have an fe80 address. When I check in the journal my isp is giving my an ipv6 address 1250:~ # journalctl -b |grep wickedd-dhcp6 Dec 22 19:35:36 n1250 wickedd-dhcp6[937]: enp5s6: Request to acquire DHCPv6 lease with UUID e8b23d5a-d5d0-0600-ab03-000007000000 in mode auto Dec 22 19:35:54 n1250 wickedd-dhcp6[937]: enp5s6: Committed DHCPv6 lease with addresses: Dec 22 19:35:54 n1250 wickedd-dhcp6[937]: 2605:a000:xxxx:x:xxxx:b1bd: 1859:c410, pref-lft 604800, valid-lft 604800 Here's my 50-router.conf n1250:~ # cat /etc/sysctl.d/50-router.conf net.ipv4.conf.all.forwarding = 1 net.ipv6.conf.all.forwarding = 1 net.ipv4.conf.all.rp_filter = 0 net.ipv6.conf.enp5s6.accept_ra = 2 net.ipv6.conf.enp5s6.autoconf = 0 Any ideas on how to assign the ipv6 address? Thanks for any assistance. Mark -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse+owner@opensuse.org