Hello All Some point of my configuration: 1. Installation: from CD. I couldn't update my installation because of the problem. 2. The network card was detected in the boot sequence. 3. I tried using YAST before posting. 4. An output of ifconfig command: linux:~ # ifconfig eth0 Link encap:Ethernet HWaddr 00:0F:B0:72:33:2D inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20f:b0ff:fe72:332d/64 Scope:Link UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1 RX packets:147 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:43220 (42.2 Kb) TX bytes:2936 (2.8 Kb) Interrupt:10 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:223 errors:0 dropped:0 overruns:0 frame:0 TX packets:223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22068 (21.5 Kb) TX bytes:22068 (21.5 Kb) linux:~ # date Tue Aug 30 15:11:44 MDT 2005 5. An partial output of my /var/log/messages ( cat /var/log/messages|grep eth0 ): Aug 30 14:57:07 linux kernel: eth0: RealTek RTL8139 at 0xf925e400, 00:0f:b0:72:33:2d, IRQ 10 Aug 30 14:57:07 linux kernel: eth0: Identified 8139 chip type 'RTL-8100B/8139D' Aug 30 14:57:18 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 14:57:41 linux kernel: eth0: no IPv6 routers present Aug 30 14:57:42 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 14:57:42 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 14:57:42 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 14:57:42 linux kernel: eth0: Tx descriptor 0 is 0008a24e. (queue head) Aug 30 14:57:42 linux kernel: eth0: Tx descriptor 1 is 0008a24e. Aug 30 14:57:42 linux kernel: eth0: Tx descriptor 2 is 0008a24e. Aug 30 14:57:42 linux kernel: eth0: Tx descriptor 3 is 0008a056. Aug 30 14:57:42 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 14:57:54 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 14:57:54 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 14:57:54 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 14:57:54 linux kernel: eth0: Tx descriptor 0 is 0008a04e. (queue head) Aug 30 14:57:54 linux kernel: eth0: Tx descriptor 1 is 0008a046. Aug 30 14:57:54 linux kernel: eth0: Tx descriptor 2 is 0008a24e. Aug 30 14:57:54 linux kernel: eth0: Tx descriptor 3 is 0008a056. Aug 30 14:57:54 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 14:58:06 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 14:58:06 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 14:58:06 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 14:58:06 linux kernel: eth0: Tx descriptor 0 is 0008a046. (queue head) Aug 30 14:58:06 linux kernel: eth0: Tx descriptor 1 is 0008a046. Aug 30 14:58:06 linux kernel: eth0: Tx descriptor 2 is 0008a24e. Aug 30 14:58:06 linux kernel: eth0: Tx descriptor 3 is 0008a24e. Aug 30 14:58:06 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:01:18 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:01:18 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:01:18 linux kernel: eth0: Tx queue start entry 20 dirty entry 16. Aug 30 15:01:18 linux kernel: eth0: Tx descriptor 0 is 0008a079. (queue head) Aug 30 15:01:18 linux kernel: eth0: Tx descriptor 1 is 0008a062. Aug 30 15:01:18 linux kernel: eth0: Tx descriptor 2 is 0008a062. Aug 30 15:01:18 linux kernel: eth0: Tx descriptor 3 is 0008a062. Aug 30 15:01:18 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:01:30 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:01:30 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:01:30 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:01:30 linux kernel: eth0: Tx descriptor 0 is 0008a062. (queue head) Aug 30 15:01:30 linux kernel: eth0: Tx descriptor 1 is 0008a062. Aug 30 15:01:30 linux kernel: eth0: Tx descriptor 2 is 0008a062. Aug 30 15:01:30 linux kernel: eth0: Tx descriptor 3 is 0008a062. Aug 30 15:01:30 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:01:42 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:01:42 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:01:42 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:01:42 linux kernel: eth0: Tx descriptor 0 is 0008a062. (queue head) Aug 30 15:01:42 linux kernel: eth0: Tx descriptor 1 is 0008a062. Aug 30 15:01:42 linux kernel: eth0: Tx descriptor 2 is 0008a062. Aug 30 15:01:42 linux kernel: eth0: Tx descriptor 3 is 0008a062. Aug 30 15:01:42 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:01:54 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:01:54 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:01:54 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:01:54 linux kernel: eth0: Tx descriptor 0 is 0008a062. (queue head) Aug 30 15:01:54 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:01:54 linux kernel: eth0: Tx descriptor 2 is 0008a062. Aug 30 15:01:54 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:01:54 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:02:06 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:02:06 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:02:06 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:02:06 linux kernel: eth0: Tx descriptor 0 is 0008a062. (queue head) Aug 30 15:02:06 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:02:06 linux kernel: eth0: Tx descriptor 2 is 0008a062. Aug 30 15:02:06 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:02:06 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:02:18 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:02:18 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:02:18 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:02:18 linux kernel: eth0: Tx descriptor 0 is 0008a079. (queue head) Aug 30 15:02:18 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:02:18 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:02:18 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:02:18 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:02:30 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:02:30 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:02:30 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:02:30 linux kernel: eth0: Tx descriptor 0 is 0008a03c. (queue head) Aug 30 15:02:30 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:02:30 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:02:30 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:02:30 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:02:42 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:0Aug 30 15:08:54 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:08:54 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:08:54 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:09:06 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:09:06 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:09:06 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:09:06 linux kernel: eth0: Tx descriptor 0 is 0008a03c. (queue head) Aug 30 15:09:06 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:09:06 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:09:06 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:09:06 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:09:18 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:09:18 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:09:18 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:09:18 linux kernel: eth0: Tx descriptor 0 is 0008a03c. (queue head) Aug 30 15:09:18 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:09:18 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:09:18 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:09:18 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:09:30 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:09:30 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:09:30 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:09:30 linux kernel: eth0: Tx descriptor 0 is 0008a03c. (queue head) Aug 30 15:09:30 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:09:30 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:09:30 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:09:30 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Aug 30 15:09:42 linux kernel: NETDEV WATCHDOG: eth0: transmit timed out Aug 30 15:09:42 linux kernel: eth0: Transmit timeout, status 0c 0005 c07f media 10. Aug 30 15:09:42 linux kernel: eth0: Tx queue start entry 4 dirty entry 0. Aug 30 15:09:42 linux kernel: eth0: Tx descriptor 0 is 0008a03c. (queue head) Aug 30 15:09:42 linux kernel: eth0: Tx descriptor 1 is 0008a03c. Aug 30 15:09:42 linux kernel: eth0: Tx descriptor 2 is 0008a03c. Aug 30 15:09:42 linux kernel: eth0: Tx descriptor 3 is 0008a03c. Aug 30 15:09:42 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 6. All the /var/log/boot.msg linux:~ # more /var/log/boot.msg Inspecting /boot/System.map-2.6.11.4-20a-default Loaded 22815 symbols from /boot/System.map-2.6.11.4-20a-default. Symbols match kernel version 2.6.11. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. <4>Linux version 2.6.11.4-20a-default (geeko@buildhost) (gcc version 3.3.5 20050117 (prerelease) (SUSE Linux)) #1 Wed Mar 2 3 21:52:37 UTC 2005 <6>BIOS-provided physical RAM map: <4> BIOS-e820: 0000000000000000 - 000000000009f800 (usable) <4> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) <4> BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) <4> BIOS-e820: 0000000000100000 - 000000007fef0000 (usable) <4> BIOS-e820: 000000007fef0000 - 000000007feff000 (ACPI data) <4> BIOS-e820: 000000007feff000 - 000000007ff00000 (ACPI NVS) <4> BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved) <4> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) <4> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) <4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) <4> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) <5>1150MB HIGHMEM available. <5>896MB LOWMEM available. <6>found SMP MP-table at 000f7e20 <7>On node 0 totalpages: 524016 <7> DMA zone: 4096 pages, LIFO batch:1 <7> Normal zone: 225280 pages, LIFO batch:16 <7> HighMem zone: 294640 pages, LIFO batch:16 <6>DMI present. <7>ACPI: RSDP (v000 PTLTD ) @ 0x000f7df0 <7>ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x7fef9511 <7>ACPI: FADT (v001 HP Piranha 0x06040000 ATI 0x000f4240) @ 0x7fefee27 <7>ACPI: MCFG (v001 ATI Piranha 0x06040000 LOHR 0x0000005f) @ 0x7fefee9b <7>ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x7fefeed7 <7>ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7fefefa6 <7>ACPI: DSDT (v001 HP 3085 0x06040000 MSFT 0x0100000e) @ 0x00000000 <6>ACPI: PM-Timer IO Port: 0x8008 <6>ACPI: local apic disabled <6>Intel MultiProcessor Specification v1.4 <6> Virtual Wire compatibility mode. <6>OEM ID: Product ID: APIC at: 0xFEE00000 <4>Processor #0 15:15 APIC version 16 <6>I/O APIC #1 Version 33 at 0xFEC00000. <6>Processors: 1 <4>Allocating PCI resources starting at 80000000 (gap: 80000000:60000000) <4>Built 1 zonelists <4>Kernel command line: root=/dev/hda2 vga=0x317 selinux=0 splash=silent resume=/dev/hda1 <6>bootsplash: silent mode. <6>Initializing CPU#0 <4>PID hash table entries: 4096 (order: 12, 65536 bytes) <4>Detected 995.299 MHz processor. <6>Using pmtmr for high-res timesource <4>Console: colour dummy device 80x25 <4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 2073460k/2096064k available (1865k kernel code, 21696k reserved, 659k data, 204k init, 1178560k highmem) <4>Checking if this processor honours the WP bit even in supervisor mode... Ok. <7>Calibrating delay loop... 1961.98 BogoMIPS (lpj=980992) <6>Security Framework v1.0.0 initialized <6>SELinux: Disabled at boot. <4>Mount-cache hash table entries: 512 (order: 0, 4096 bytes) <7>CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000 <7>CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000 <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 512K (64 bytes/line) <7>CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010 00000000 00000000 00000000 <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#0. <4>CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00 <6>Enabling fast FPU save and restore... done. <6>Enabling unmasked SIMD FPU exception support... done. <6>Checking 'hlt' instruction... OK. <6>checking if image is initramfs... it is <6>Freeing initrd memory: 1329k freed <6>ACPI: Looking for DSDT in initrd... not found! <4> not found! <4>ACPI: setting ELCR to 0200 (from 0c00) linux:~ # cat /var/log/boot.msg|grep eth0 done eth0 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) eth0 configuration: eth-id-00:0f:b0:72:33:2d eth0 (DHCP) . . . . . <notice>startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ LC_MONETARY= CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_NUMERIC= QTDIR=/usr/lib/qt3 LC_ALL= INIT_VERSION=sysvinit-2.85 INIT=/sbin/init KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=127 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/lib/klibc/bin LC_MESSAGES= vga=0x317 RUNLEVEL=5 LC_COLLATE= SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1024x768.cfg PWD=/ LANG=en_US.UTF-8 ROOTFS_REALDEV=/lib/klibc//dev/hda2 PREVLEVEL=N LINES=44 SHLVL=2 HOME=/ XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/X11R6/bin/kde LC_CTYPE=en_US.UTF-8 SPLASH=yes splash=silent LC_TIME= ROOTFS_BLKDEV=/dev/hda2 _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ] 7. The route -n command: linux:~ # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 linux:~ # ping 192.168.1.0 Do you want to ping broadcast? Then -b linux:~ # ping 169.254.0.0 PING 169.254.0.0 (169.254.0.0) 56(84) bytes of data.
From 192.168.1.103: icmp_seq=2 Destination Host Unreachable From 192.168.1.103 icmp_seq=2 Destination Host Unreachable From 192.168.1.103 icmp_seq=3 Destination Host Unreachable From 192.168.1.103 icmp_seq=4 Destination Host Unreachable From 192.168.1.103 icmp_seq=6 Destination Host Unreachable From 192.168.1.103 icmp_seq=7 Destination Host Unreachable From 192.168.1.103 icmp_seq=8 Destination Host Unreachable
--- 169.254.0.0 ping statistics --- 8 packets transmitted, 0 received, +7 errors, 100% packet loss, time 6999ms , pipe 3 --- Scott Leighton <helphand@pacbell.net> escribió:
Hello
I installed Suse 9.3 on HP pavillion zv6131us (AMD 64). The installer detects a network card, and everything looked fine, but when the installer
On Monday 29 August 2005 11:49 am, Victor Montes wrote: tried
to connect to the internet (seeking for updates) it failed.
After that, i tried to change some parameters (DHCP, fix IP, for example) but nothing, the error when I tried to reach any ip (for example a dns server) is 'Destination unreachable'.
Any suggestions/help. Sorry if it is a basic one, I am trying to move from Windows to Linux.
I don't know if there is a way to validate the parameters of the network card or maybe if it is mandatory any patch or something.
From a root shell, type
ifconfig
To see what is configured for your NIC.
Scott
-- POPFile, the OpenSource EMail Classifier http://popfile.sourceforge.net/ Linux 2.6.11.4-21.8-default x86_64 SuSE Linux 9.3 (x86-64)
-- Check the headers for your unsubscription address For additional commands send e-mail to suse-linux-e-help@suse.com Also check the archives at http://lists.suse.com Please read the FAQs: suse-linux-e-faq@suse.com
__________________________________________________ Correo Yahoo! Espacio para todos tus mensajes, antivirus y antispam ¡gratis! Regístrate ya - http://correo.espanol.yahoo.com/