Hi :) Sorry for cross-posting, but not sure whether one or the other list should be e-mailed. Seems to me that both are eligeble 0;) Just installed openSUSE 11.1 on my Asus R2Hv and I'm having issues with my gfx card (see lspci below). If I use the "i810" driver I get this error: [...] (II) Primary Device is: PCI 00@00:02:0 (EE) No devices detected. Fatal server error: no screens found But if I use the "intel" driver I get this other error: Couldn't find PLL settings for mode! I've been looking through bugzilla and found that this issue was detected during the Beta phase and has been closed as "fixed": https://bugzilla.novell.com/show_bug.cgi?id=432422 Seems xorg/X11 Intel gfx drivers need a patch and seems it's been applied (bugzilla says so), but doesn't seem to work for me :( I've tried adding these lines to xorg.conf, but still doesn't work: BusID "0:2:0" BusID "PCI:0:2:0" Also tried using the VESA driver, no go. ¿Any ideas, hints, tips, ...? BTW, lspci -nnvv gives me this: 00:02.0 VGA compatible controller [Class 0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 04) (prog-if 00 [VGA]) Subsystem: ASUSTeK Computer Inc. Unknown device [1043:12f7] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at feb80000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at ec00 [size=8] Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at feb40000 (32-bit, non-prefetchable) [size=256K] Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.1 Display controller [Class 0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 04) Subsystem: ASUSTeK Computer Inc. Unknown device [1043:12f7] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at fea80000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- TIA Rafa -- "We cannot treat computers as Humans. Computers need love." rgriman@skype.com -- To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org For additional commands, e-mail: opensuse+help@opensuse.org