-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Content-ID: <alpine.LSU.1.00.0801212334060.27259@nimrodel.valinor> El 2008-01-21 a las 21:52 +0100, Octavio escribió:
Bueno, vamos a ver como salió esto. A continuación os pongo el log del envio:
... Jan 21 20:43:03.32: [30105]: SEND file "docq/cover18;c1" ...
Jan 21 20:43:16.71: [30105]: <-- data [7] Jan 21 20:43:16.71: [30105]: <-- data [2] Jan 21 20:43:18.13: [30105]: --> [2:OK] Jan 21 20:43:18.13: [30105]: SEND send PPS (partial page signal) Jan 21 20:43:18.13: [30105]: SEND send MPS (more pages, same document) Jan 21 20:43:18.13: [30105]: <-- [9:AT+FRH=3\r] Jan 21 20:43:18.38: [30105]: --> [7:CONNECT] Jan 21 20:43:19.50: [30105]: --> [2:OK] Jan 21 20:43:19.50: [30105]: SEND recv MCF (message confirmation) Jan 21 20:43:19.50: [30105]: DELAY 70 ms Jan 21 20:43:19.57: [30105]: SEND end page
Hasta aquí ha enviado la primera hoja bien (la portada).
Jan 21 20:43:20.58: [30105]: SEND file "docq/doc25.ps;c1"
Y este es el documento, que lo deberías encontrar en /var/spool/fax/docq/doc25.ps
Jan 21 20:43:20.58: [30105]: SEND begin page Jan 21 20:43:20.61: [30105]: SEND EOFB Jan 21 20:43:20.61: [30105]: SEND send frame number 0 Jan 21 20:43:20.61: [30105]: SEND send frame number 1 Jan 21 20:43:20.61: [30105]: SEND send frame number 2 ... Jan 21 20:43:20.63: [30105]: SEND send frame number 97 Jan 21 20:43:20.63: [30105]: SEND send frame number 98 Jan 21 20:43:20.63: [30105]: SEND send frame number 99 Jan 21 20:43:20.63: [30105]: <-- [11:AT+FTM=146\r] Jan 21 20:43:21.12: [30105]: --> [7:CONNECT] Jan 21 20:43:21.12: [30105]: <-- data [1029] ... Jan 21 20:43:34.53: [30105]: <-- data [873] Jan 21 20:43:34.97: [30105]: <-- data [2] Jan 21 20:43:34.97: [30105]: --> [10:NO CARRIER]
¡Se pierde la portadora! Yo diría que es la linea.
Jan 21 20:43:34.97: [30105]: SEND end page Jan 21 20:43:34.97: [30105]: Unspecified Transmit Phase C error Jan 21 20:43:34.97: [30105]: DELAY 70 ms Jan 21 20:43:35.04: [30105]: <-- [9:AT+FTH=3\r] Jan 21 20:43:42.59: [30105]: --> [0:] Jan 21 20:43:43.59: [30105]: <-- [5:ATH0\r] Jan 21 20:43:43.82: [30105]: --> [2:OK] Jan 21 20:43:43.95: [30105]: SESSION END
¿Tendré mal la velocidad?
No, pero... Jan 21 20:43:03.32: [30105]: REMOTE format support: MH, MR, MMR Jan 21 20:43:03.32: [30105]: REMOTE supports T.30 Annex A, 256-byte ECM Jan 21 20:43:03.32: [30105]: REMOTE best 0 ms/scanline Jan 21 20:43:03.32: [30105]: USE 14400 bit/s Jan 21 20:43:03.32: [30105]: USE error correction mode Jan 21 20:43:03.32: [30105]: SEND file "docq/cover18;c1" Jan 21 20:43:03.32: [30105]: USE A4 page width (215 mm) Jan 21 20:43:03.32: [30105]: USE unlimited page length Jan 21 20:43:03.32: [30105]: USE 7.7 line/mm Jan 21 20:43:03.32: [30105]: USE 2-D MMR <============= Jan 21 20:43:03.32: [30105]: USE 0 ms/scanline Jan 21 20:43:03.32: [30105]: SEND training at v.17 14400 bit/s FRM es un modo de compresión avanzado que presupone que la línea no tiene ruido ni errores, como las digitales. A lo mejor se puede desactivar. [..] En el directorio "/var/spool/fax/config" hay ejemplos de eso. lucent-mt-21: # Some firmware revisions (i.e. 1.25) report MMR support but corrupt the data. # Some firmware revisions (i.e. 1.25 and 1.28) report extended resolution support but # have trouble with 300x300 and 400x400 resolutions and corrupt DIS for inch resolutions. # Enabling the following lines should work around these things. # Compare this against the modem's AT+FCC=? response. # Class2DCCQueryCmd: "!(03),(00-05),(00-02),(00-02),(00-01),(00-01),(00),(00-07)" # ModemAnswerCmd: AT+FCC=03,,,,1,,,,0;A # ModemDialCmd: AT+FCC=03,,,,1,,,,0;DT%s No estoy seguro de como se hace eso, es un tiro al aire... pero podría ser. Debería haber un registro en el modem que controlara esos modos :-? Pero mi manual de modem no veo nada. - -- Saludos Carlos E.R. -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.4-svn0 (GNU/Linux) iD8DBQFHlSyBtTMYHG2NR9URAmcmAJ4w+9pKhIKm7YYfBzMHner6Im0u6ACcD2fd n3p/UnivD3Qo8FVBNOMXUVo= =4DFo -----END PGP SIGNATURE-----