Bueno, bueno, bueno, Acabo de enviar un fax con dos hojas incluida la portada. Y resulta que no me ha dado error. Lo ha enviado a la primera al menos eso me pone en el panel de fax enviados, entre los que figura un signo de verificación verde en el medio de una lista de cruces rojas (parece una canción de los Ramones). Pero qué hice, para que se produjese este milagro. En honor a la realidad, tenemos que preguntarnos qué hicisteis: Cambiarle el firmware por el de Cass1. El fichero quedó de la siguiente forma: # $Id: topic,v 1.4 2003/07/25 16:23:26 lhoward Exp $ # # prototype config for Topic modems and other similarly broken firmwares # # CountryCode: 34 AreaCode: 981 FAXNumber: XXXXXXXXXX LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: "etc/dialrules" ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0777 LogFileMode: 0777 DeviceMode: 0777 RingsBeforeAnswer: 6 SpeakerVolume: medium GettyArgs: "-r -b -s %s %l" LocalIdentifier: "TEVISAN" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 # ModemType: Class1 # use this to supply a hint # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint #ModemRate: 19200 # rate for DCE-DTE communication #ModemFlowControl: xonxoff # XON/XOFF flow control assumed # #ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem #ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier #GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data # # We can append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s # T for tone dialing # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # #ModemResetCmds: "" # stuff to do when modem is reset #ModemAnswerCmd: ATA # use this to answer phone #ModemNoFlowCmd: AT&K # disable flow control cmd #ModemHardFlowCmd: AT&K3 # hardware flow control cmd #ModemSoftFlowCmd: AT&K4 # software flow control cmd #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH0 # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemSoftResetCmdDelay: 3000 # pause after soft reset #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans Class1RecvAbortOK: 200 # wait 200ms for abort response Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration Un saludo y qué deciros. Muchas gracias por todo -- Octavio Ávalos --------------------------------------------------------------------- Para dar de baja la suscripción, mande un mensaje a: opensuse-es+unsubscribe@opensuse.org Para obtener el resto de direcciones-comando, mande un mensaje a: opensuse-es+help@opensuse.org