Tach zusammen, (schon) wieder ein neuer Linux-User in der Liste und wahrscheinlich wieder die Frage nach der Möglichkeit zwischen den Modulen lp und ppa zu wechseln. Der Weg als root ist mir bekannt; ich suche einen elegante Möglichkeit (Vers.5.3) für alle anderen User. Ich bin noch nicht hinter die Zugangs- bzw. Ausführungsrechte von modeprobe etc. gekommen, vielleicht gibt es aber schon eine weniger befehlsorientierte Möglichkeit. d anke teg -- Um aus der Liste ausgetragen zu werden, eine Mail an majordomo@suse.com schicken, mit dem Text: unsubscribe suse-linux
Hi, On Sat, Jan 02, 1999 at 20:20 +0100, Torsten E. Gnther wrote:
(schon) wieder ein neuer Linux-User in der Liste und wahrscheinlich wieder die Frage nach der Möglichkeit zwischen den Modulen lp und ppa zu wechseln. Der Weg als root ist mir bekannt; ich suche einen elegante Möglichkeit (Vers.5.3) für alle anderen User. Ich bin noch nicht hinter die Zugangs- bzw. Ausführungsrechte von modeprobe etc. gekommen, vielleicht gibt es aber schon eine weniger befehlsorientierte Möglichkeit.
Sieh Dir mal sudo an, damit kannst Du es normalen Usern erlauben, Befehle als root auszuführen. Ciao, Stefan -- Um aus der Liste ausgetragen zu werden, eine Mail an majordomo@suse.com schicken, mit dem Text: unsubscribe suse-linux
On 04-Jan-99 Stefan Troeger wrote:
(schon) wieder ein neuer Linux-User in der Liste und wahrscheinlich wieder die Frage nach der Möglichkeit zwischen den Modulen lp und ppa zu wechseln. Der Weg als root ist mir bekannt; ich suche einen elegante Möglichkeit (Vers.5.3) für alle anderen User. Ich bin noch nicht hinter die Zugangs- bzw. Ausführungsrechte von modeprobe etc. gekommen, vielleicht gibt es aber schon eine weniger befehlsorientierte Möglichkeit.
Sieh Dir mal sudo an, damit kannst Du es normalen Usern erlauben, Befehle als root auszuführen.
Hallo, die bessere Möglichkeit ist, mit kerneld zu arbeiten. Wenn gedruckt werden soll, lädt der Kernel automatisch lp.o und wenn das ZIP gemountet wird, dann wird automatisch ppa.o geladen. Falls Du das alles, was mit SCSI zu tun hat modularisiert hast, ist es günstig/etc/conf.modules anzupassen. Bei mir steht da: pre-install sd_mod modprobe -k ppa Das -k bei modeprobe sagt, dass das Modul mit autoclean geladen wird. Die beste Möglichkeit ist, einen Hackerkernel zu verwenden; z.B. die 2.1.131 oder 2.1.132 oder eine (hoffentlich) bald verfügbare, funktionierende 2.2.er Version. In diesen kann der parallele Port nähmlich geshared werden, d.h. Du kannst gleichzeiteig Drucken und auf das ZIP! Allerdings solltes Du die Kernelkonfiguration sorfältig durchlesen, da sich beim Laden und Entladen von Modulen durch den Kernel einiges geändert hat (siehe Documentation/kmod.txt) und außerdem hat sich in den Hackerkernel die Numerierung der parallelen Schnittstellen gaändert: lp1 -> lp0 ! Viel Glück, Carsten -- Um aus der Liste ausgetragen zu werden, eine Mail an majordomo@suse.com schicken, mit dem Text: unsubscribe suse-linux
participants (3)
-
schurigc@physik.phy.tu-dresden.de
-
stefan.troeger@wirtschaft.tu-chemnitz.de
-
Torsten.E.Guenther@geo.uni-giessen.de