Problem mit einem USB-Gerät, will einfach nicht, SuSE 10.1
Hallo, SuSE 10.1 Ich habe einen USB-Stick der sehr gut funktioniert. Leider funktioniert ein anderes Gerät überhaupt nicht. Ich habe das Gerät unter FreeBSD problemlos zum laufen bekommen. Woran kann das liegen? Hier ein Auszug aus der /var/log/messages beim ein und ausstecken der beiden Geräte (das, welches funktioniert, und das, welches nicht funktioniert): ohci_hcd 0000:00:02.3: OHCI Host Controller ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.3: irq 193, io mem 0xef000000 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.16.13-4-default ohci_hcd usb usb2: SerialNumber: 0000:00:02.3 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usb 1-1: new full speed USB device using ohci_hcd and address 2 usb 1-1: new device found, idVendor=10d6, idProduct=1100 usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=2 usb 1-1: Product: USB MASS STORAGE CLASS usb 1-1: SerialNumber: USB MASS STORAGE CLASS usb 1-1: configuration #1 chosen from 1 choice SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. Vendor: Model: Rev: Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete Driver 'sd' needs updating - please use bus_type methods SCSI device sda: 2000609 512-byte hdwr sectors (1024 MB) sda: Write Protect is off sda: Mode Sense: 00 c0 00 00 sda: assuming drive cache: write through SCSI device sda: 2000609 512-byte hdwr sectors (1024 MB) sda: Write Protect is off sda: Mode Sense: 00 c0 00 00 sda: assuming drive cache: write through sda: unknown partition table sd 0:0:0:0: Attached scsi removable disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 usb 1-2: new full speed USB device using ohci_hcd and address 3 usb 1-2: new device found, idVendor=0421, idProduct=045b usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-2: Product: Nokia 6280 usb 1-2: Manufacturer: Nokia usb 1-2: SerialNumber: 353949013107215 usb 1-2: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning Vendor: Nokia Model: Nokia 6280 Rev: 0000 Type: Direct-Access ANSI SCSI revision: 04 SCSI device sdb: 124161 512-byte hdwr sectors (64 MB) sdb: test WP failed, assume Write Enabled sdb: assuming drive cache: write through SCSI device sdb: 124161 512-byte hdwr sectors (64 MB) sdb: test WP failed, assume Write Enabled sdb: assuming drive cache: write through sdb: sd 1:0:0:0: Attached scsi removable disk sdb sd 1:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete sdb: Current: sense key: No Sense Additional sense: No additional sense information agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R200 Microcode Was kann ich dagegen unternehmen? Danke Karl -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
Hallo, ich habe es jetzt noch mal mit der Knoppix 4.02 versucht, und da funktioniert das Gerät einwandfrei. HIer ein Auszug aus der /var/log/messages von Knoppix: _________________________________________begin usb 1-1: new full speed USB device using ohci_hcd and address 2 scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning Vendor: Nokia Model: Nokia 6280 Rev: 0000 Type: Direct-Access ANSI SCSI revision: 04 SCSI device sda: 124161 512-byte hdwr sectors (64 MB) sda: test WP failed, assume Write Enabled sda: assuming drive cache: write through SCSI device sda: 124161 512-byte hdwr sectors (64 MB) sda: test WP failed, assume Write Enabled sda: assuming drive cache: write through sda: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 usb-storage: device scan complete __________________________________________end Im Anhang sende ich die Ausgabe von /var/log/messages mit der SuSE 10.1 da stolpere ich über folgende Zeile: Dec 23 17:56:45 paris kernel: Driver 'sd' needs updating - please use bus_type methods Ist das mein Problem? Muss ich bus_type methods benutzen? Und wenn ja was bedeutet das genau? Gruss Karl Hier der Entsprechende Eintrag von meiner SuSE beim Einstecken des Gerätes: ________________________________________begin Dec 23 17:56:39 paris kernel: usb 1-1: new full speed USB device using ohci_hcd and address 2 Dec 23 17:56:39 paris kernel: usb 1-1: new device found, idVendor=0421, idProduct=045b Dec 23 17:56:39 paris kernel: usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 Dec 23 17:56:39 paris kernel: usb 1-1: Product: Nokia 6280 Dec 23 17:56:39 paris kernel: usb 1-1: Manufacturer: Nokia Dec 23 17:56:39 paris kernel: usb 1-1: SerialNumber: 353949013107215 Dec 23 17:56:39 paris kernel: usb 1-1: configuration #1 chosen from 1 choice Dec 23 17:56:39 paris kernel: SCSI subsystem initialized Dec 23 17:56:39 paris kernel: Initializing USB Mass Storage driver... Dec 23 17:56:39 paris kernel: scsi0 : SCSI emulation for USB Mass Storage devices Dec 23 17:56:39 paris kernel: usb-storage: device found at 2 Dec 23 17:56:39 paris kernel: usb-storage: waiting for device to settle before scanning Dec 23 17:56:39 paris kernel: usbcore: registered new driver usb-storage Dec 23 17:56:39 paris kernel: USB Mass Storage support registered. Dec 23 17:56:44 paris kernel: Vendor: Nokia Model: Nokia 6280 Rev: 0000 Dec 23 17:56:44 paris kernel: Type: Direct-Access ANSI SCSI revision: 04 Dec 23 17:56:44 paris kernel: usb-storage: device scan complete Dec 23 17:56:45 paris kernel: Driver 'sd' needs updating - please use bus_type methods Dec 23 17:56:45 paris kernel: SCSI device sda: 124161 512-byte hdwr sectors (64 MB) Dec 23 17:56:45 paris kernel: sda: test WP failed, assume Write Enabled Dec 23 17:56:45 paris kernel: sda: assuming drive cache: write through Dec 23 17:56:45 paris kernel: SCSI device sda: 124161 512-byte hdwr sectors (64 MB) Dec 23 17:56:45 paris kernel: sda: test WP failed, assume Write Enabled Dec 23 17:56:45 paris kernel: sda: assuming drive cache: write through Dec 23 17:56:45 paris kernel: sda: Dec 23 17:56:45 paris kernel: sd 0:0:0:0: Attached scsi removable disk sda Dec 23 17:56:45 paris kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0 Dec 23 17:56:46 paris kernel: sda: Current: sense key: No Sense Dec 23 17:56:46 paris kernel: Additional sense: No additional sense information Dec 23 17:56:53 paris kernel: usb 1-1: reset full speed USB device using ohci_hcd and address 2 _________________________________________end -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
participants (1)
-
Karl Sinn