XDM startet nicht mehr nach Update 6.2->6.4
Vor der Aktualisierung habe ich auf ASCII-Login umgestellt. Die Aktualisierung auf Suse 6.4 ging reibungslos vonstatten, nur jetzt kann ich die grafische Oberfläche nur dann starten, wenn ich explizit "startx kde" angebe! (Auch nachdem ich mit yast auf grafische Login-Konfiguration umgestellt habe). Woher kommt das? Und tschüß R. Castillo --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
*On Fri, Jun 02, 2000 at 04:33:02PM +0100, roderick.castillo@dolphin-telecom.de wrote:
Vor der Aktualisierung habe ich auf ASCII-Login umgestellt. Die Aktualisierung auf Suse 6.4 ging reibungslos vonstatten, nur jetzt kann ich die grafische Oberfläche nur dann starten, wenn ich explizit "startx kde" angebe! (Auch nachdem ich mit yast auf grafische Login-Konfiguration umgestellt habe).
Woher kommt das?
Keine Ahnung, ...event was beim update schief gelaufen (??)? Aber du kannst auch selber Hand anlegen,..... welcher runlevel beim booten gestartet wird, wird in der /etc/initab festgehalten. Sieht so aus für den runlevel 2: # default runlevel id:2:initdefault: Setze es auf: id:3:initdefault: ...und achte auf den Startlink des xdm in /sbin/init.d/rc3.d! Sonst wird kein X gestartet. Du weißt was die runlevel unter Linux machen? Schau dir /sbin/init.d/* an, da liegen scripte zum starten von Programmen/daemonen usw. rc0.d ist HALT rc1.d ist runlevel; 1 ohne X und ohne Netzwerk rc2.d ist runlevel 2; ohne X mit Netzwerk rc3.d ist runlevel 3; mit X und Netzwerk rc6.d ist REBOOT Die originale liegen unter /sbin/init.d/* und werden als S (Start) und K (Stop) und der Reihenfolge (per Nummer davor) in die runlevel gelinkt. Also bei dir sollte der xdm (schon installiert?) als S30xdm und K10xdm in den runlevel 3 gelinkt werden. Natürlich könnte man auch den xdm auch im runlevel 2 starten lassen, aber würd ich nicht machen. Bevor man an den runleveln rumspielt sollte man wissen was man tut! Lass es bei den vorgeschlagenen runlevels erstmal. Dann ist noch das script /sbin/init.d/boot.local, dort kann man eigene scripte starten lassen. ZB. lasse ich dort meine firewall einlesen (eigene chains) und setterm-Aufruf für das blanken von bestimmten consolen usw. Wie man die runlevel nun gestaltet,..ist jedem sein Bier. Solange alles funzt... Aber die Vorgabe ist schon OK ...wenn man nichts besonderes vor hat. Gruß, Clemens -- sig_15 "The program isn't debugged until the last user is dead" [Registered Linux-User #115060] [c.wohld@gmx.de] [X-Page: http://www.ndh.net/home/wohld/index.html] ------------------------------------------------------- --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
participants (2)
-
c.wohld@ndh.net
-
roderick.castillo@dolphin-telecom.de