Rufe ich mit einem IBM 300PL (Onboard-Grafik) und TNT2-PCI-Grafikkarte unter SuSE 10.0 sax2 auf, so bleibt der Bildschirm schwarz. Interessant war, dass nach Ausbau der PCI-Graka und Konfiguration mit yast Pakete nachgeladen wurden. Der Rechner wurde mit Onboard-Graka aufgesetzt und bei der Installation hat alles gepasst. Gefühlsmäßig findet sax2 das Display nicht. Ich denke daher, vielleicht hilft es, wenn ich sax2 möglichst viel an Infos mitgebe. Was könnte ich probieren? Es folgen einige Hardware-Infos. Interrupts: CPU0 0: 240027 XT-PIC timer 1: 10 XT-PIC i8042 2: 0 XT-PIC cascade 5: 1 XT-PIC CS4231 7: 3 XT-PIC parport0 8: 3 XT-PIC rtc 9: 0 XT-PIC acpi 11: 12358 XT-PIC uhci_hcd:usb1, eth0 12: 127 XT-PIC i8042 14: 10781 XT-PIC ide0 15: 42817 XT-PIC ide1 NMI: 0 LOC: 0 ERR: 2 MIS: 0 hwinfo --gfxcard 17: PCI 14.0: 0300 VGA compatible controller (VGA) [Created at pci.277] UDI: /org/freedesktop/Hal/devices/pci_10de_2d SysFS ID: /devices/pci0000:00/0000:00:14.0 SysFS BusID: 0000:00:14.0 Hardware Class: graphics card Model: "Creative RIVA TNT2 Model 64/Model 64 Pro" Vendor: pci 0x10de "nVidia Corporation" Device: pci 0x002d "RIVA TNT2 Model 64/Model 64 Pro" SubVendor: pci 0x1102 "Creative Labs" SubDevice: pci 0x1046 Revision: 0x15 Memory Range: 0xf3000000-0xf3ffffff (rw,non-prefetchable) Memory Range: 0xf0000000-0xf1ffffff (rw,prefetchable) Memory Range: 0x14100000-0x1410ffff (ro,prefetchable,disabled) IRQ: 255 (no events) I/O Ports: 0x3c0-0x3df (rw) Module Alias: "pci:v000010DEd0000002Dsv00001102sd00001046bc03sc00i00" Driver Info #0: XFree86 v4 Server Module: nv Config Status: cfg=yes, avail=yes, need=yes, active=unknown 18: PCI 101.0: 0300 VGA compatible controller (VGA) [Created at pci.277] UDI: /org/freedesktop/Hal/devices/pci_5333_8904 Parent ID: vSkL.+oqW+GBE7wA SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:01.0 SysFS BusID: 0000:01:01.0 Hardware Class: graphics card Model: "S3 Integrated Trio3D" Vendor: pci 0x5333 "S3 Inc." Device: pci 0x8904 "Integrated Trio3D" Revision: 0x01 Memory Range: 0xf4000000-0xf7ffffff (rw,non-prefetchable,disabled) Memory Range: 0x14000000-0x1400ffff (ro,prefetchable,disabled) Module Alias: "pci:v00005333d00008904sv00000000sd00000000bc03sc00i00" Driver Info #0: XFree86 v4 Server Module: s3virge Config Status: cfg=yes, avail=yes, need=yes, active=unknown Attached to: #11 (PCI bridge) Primary display adapter: #17 00:14.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) 01:01.0 VGA compatible controller: S3 Inc. Trio 64 3D (rev 01) 00:14.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA]) Subsystem: Creative Labs: Unknown device 1046 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 40 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 255 Region 0: Memory at f3000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=32M] [virtual] Expansion ROM at 14100000 [disabled] [size=64K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:01.0 VGA compatible controller: S3 Inc. Trio 64 3D (rev 01) (prog-if 00 [VGA]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 0 Region 0: Memory at f4000000 (32-bit, non-prefetchable) [disabled] [size=64M] Expansion ROM at 14000000 [disabled] [size=64K] Capabilities: [44] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 3Ddiag version 0.728 Verifying 3D configuration: Using 3dinfo ************************************************************ ================================================================ No 3D capable graphic chipset found! ================================================================ Checking GL/GLU/glut runtime configuration: GL/GLU ... done (package xorg-x11-Mesa) glut ... done (package freeglut) cpu: Pentium II (Deschutes), 450 MHz keyboard: /dev/input/event1 AT Translated Set 2 keyboard mouse: /dev/input/mice ImPS/2 Logitech Wheel Mouse monitor: Generic Monitor graphics card: Creative RIVA TNT2 Model 64/Model 64 Pro S3 Integrated Trio3D sound: Crystal Audio storage: Floppy disk controller Intel 82371AB/EB/MB PIIX4 IDE network: eth0 IBM 82557/8/9 [Ethernet Pro 100] network interface: eth0 Ethernet network interface lo Loopback network interface sit0 Network Interface disk: /dev/disk/by-id/ata-Maxtor_90644D3_A319P7SC Maxtor 90644D3 /dev/disk/by-id/ata-Maxtor_90644D3_A319P74C Maxtor 90644D3 partition: /dev/disk/by-id/ata-Maxtor_90644D3_A319P7SC-part1 Partition /dev/disk/by-id/ata-Maxtor_90644D3_A319P74C-part1 Partition /dev/disk/by-id/ata-Maxtor_90644D3_A319P74C-part2 Partition /dev/disk/by-id/ata-Maxtor_90644D3_A319P74C-part3 Partition cdrom: /dev/disk/by-path/pci-0000:00:02.1-ide-0:1 TOSHIBA CD-ROM XM-6402B floppy: /dev/fd0 Floppy Disk usb controller: Intel 82371AB/EB/MB PIIX4 USB bios: BIOS bridge: Intel 440BX/ZX/DX - 82443BX/ZX/DX Host bridge Intel 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge Intel 82371AB/EB/MB PIIX4 ISA Intel 82371AB/EB/MB PIIX4 ACPI hub: Linux 2.6.13-15.8-default uhci_hcd UHCI Host Controller memory: Main Memory unknown: FPU DMA controller PIC Timer RTC Keyboard controller /dev/lp0 Parallel controller PS/2 Controller PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device PnP Unclassified device Crystal Audio Crystal Audio /dev/ttyS0 16550A /dev/ttyS1 16550A Al