nvidia grafik problem suse 9.0 32bit AMD64 Asus K8V
Hallo, vom googeln weiß ich, ich bin nicht allein. Bei der oben angegebenen Hardware bekomme ich den Grafikartentreiber in 3D, 32bit mode nicht installiert. 2D läuft. (64bit habe ich noch nicht in Erwägung gezogen) Nach der Neuinstallation mit YAST blieb der Rechner stehen "black screen" - nachdem alle Patches eingespielt waren und als letztes Nvidia 3D auf dem Programm stand. Also habe ich ihn auf init 3 gebracht und, wie Nvidia vorschlägt, 3D deinstalliert. 2D läuft nun wieder. Den Tipps von Nvidia bin ich gefolgt. (nvidia-installer-HOWTO) rmmod nvidia findet kein Installiertes Modul. Der Treiber wird von YAST neu unter init 3 heuntergeladen, YAST bleibt bei 50% Patchinstallation stehen. Irgendwelche Ideen um YAST noch zu überreden? XF86Config sagt jetzt: ------------------------- Section "Device" BoardName "0x0322" Driver "nvidia" Identifier "Device[0]" Screen 0 Option "Rotate" "off" VendorName "NVidia" EndSection ----------------------------- Gruß Peter
Am Sonntag, 29. August 2004 22:32 schrieb Peter Mc Donough:
[ ... ]
Hier. Bitteschön! ,--------------------------------------------------------------------------------------- | | I. SuSE Linux 9.0 | ----------------- | | It is recommended to use YOU (YaST Online Update) for (re)installation | of the nvidia driver. There are several reasons for this. First, it's |simple. Second, and this is the most important one, you won't need to |recompile the nvidia kernel module after a kernel update. | |Inside YOU enable "Installable and Installed Patches" for "Show Patch |Category" and select "Download NVIDIA(c) Graphics Driver" from the |patches list (usually at the bottom of the list). Note, that you need |to mark it as "Update" (right mouse click) if you already installed it |before and the driver was uninstalled - for any reason. Proceed as |usual now. After YOU has finished restart your Xserver (i.e. logout |from your Xsession) and you're fine. | |People who aren't afraid of recompiling the nvidia kernel module or |even reinstalling the nvidia driver each time the kernel has been |updated and want or need to use the latest and greatest nvidia driver |can use the following steps 1-3. The others should use the |instructions above using YOU and skip the steps below. | |1) Kernel sources must be installed and configured. Usually this means |installing the 'kernel-source' package with YaST2. Update it - if not |already done - via YaST2 Online Update (YOU). | |2) Use the nvidia installer for 1.0-6111. | | sh NVIDIA-Linux-x86-1.0-6111-pkg1.run -q | |3) Configure XFree86 with | | sax2 -m 0=nvidia (0 is a digit, not a letter!) | |NOTE: There is no need to try to enable 3D support. It's already | enabled, when the nvidia driver is running. Ignore the | misleading error message, that 3D support can't be enabled. | This problem will be fixed with SuSE > 9.0 and is related to the | latest nvidia driver release. | `---------------------------------------------------------------------------------------- ...Auszug aus der Datei ftp://ftp.gwdg.de/pub/linux/suse/ftp.suse.com/suse/i386/supplementary/X/XFree86/nvidia-installer-HOWTO -- Gruss Gunnar GnuPG-Key: 0xADECC257EFEC0F37 http://pgp.mit.edu/ Fingerprint: 3C9A B868 D3C4 1A1B A8A2 CCC6 ADEC C257 EFEC 0F37
Am Sonntag, 29. August 2004 22:32 schrieb Peter Mc Donough:
[ ... ]
Hier. Bitteschön! | |People who aren't afraid of recompiling the nvidia kernel module or |even reinstalling the nvidia driver each time the kernel has been |updated and want or need to use the latest and greatest nvidia | driver can use the following steps 1-3. The others should use the |instructions above using YOU and skip the steps below.
recht hast du, den Text habe ich hier. Aber ich verstehe darunter, das ein Recompilieren immer notwendig wird, wenn mir Yast eine Kernelupdate herunterlädt. Der "Vorteil" von Yast ist gerade der Automatismus, der wäre dann hin. Gruss Peter n andere verbessertetn Anbietet
participants (2)
-
Gunnar Salbeck -
Peter Mc Donough