Hallo zusammen, bei meinem ASUS P4B533 tut sensors nicht richtig. in der sensors.conf steht: ############################################## chip "asb100-*" set vrm 9.0 # 20050331 JK label in0 "VCore 1" set in0_min vid * 1.12 set in0_max vid * 1.25 label in1 "VCore 2" ignore in1 set in1_min vid * 0.95 set in1_max vid * 1.05 label in2 "+3.3V" set in2_min 3.3 * 0.95 set in2_max 3.3 * 1.05 label in3 "+5V" compute in3 1.68 * @ , @ / 1.68 set in3_min 5.0 * 0.95 set in3_max 5.0 * 1.05 label in4 "+12V" compute in4 3.8 * @ , @ / 3.8 set in4_min 12 * 0.90 set in4_max 12 * 1.10 label in5 "-12V (reserved)" compute in5 -@ * 3.97 , -@ / 3.97 set in5_max -12 * 0.90 set in5_min -12 * 1.10 label in6 "-5V (reserved)" #ignore in6 compute in6 -@ * 1.666 , -@ / 1.666 set in6_max -5 * 0.95 set in6_min -5 * 1.05 label temp1 "M/B Temp" set temp1_over 45 set temp1_hyst 40 label temp2 "CPU Temp (Intel)" #ignore temp2 set temp2_over 60 set temp2_hyst 50 # PWRTMP connector on P4S333, for external sensor label temp3 "Power Temp" ignore temp3 set temp3_over 45 set temp3_hyst 40 # Used for Athlon diode, ignore for P4S333 label temp4 "CPU Temp (AMD)" set temp4_over 60 set temp4_hyst 50 ignore temp4 label fan1 "CPU Fan" set fan1_div 4 set fan1_min 2000 # label fan2 "Chassis Fan" # set fan2_div 2 # set fan2_min 4000 # # label fan3 "Power Fan" # set fan3_div 2 # set fan3_min 4000 ignore fan2 ignore fan3 ###################### in der Shell erhalte ich dann: ################################ johannes-02:/etc # sensors eeprom-i2c-0-51 Adapter: SMBus I801 adapter at e800 Memory type: DDR SDRAM DIMM Memory size (MB): 512 eeprom-i2c-0-50 Adapter: SMBus I801 adapter at e800 Memory type: DDR SDRAM DIMM Memory size (MB): 512 asb100-i2c-0-2d Adapter: SMBus I801 adapter at e800 VCore 1: +1.60 V (min = +1.50 V, max = +1.68 V) +3.3V: +3.39 V (min = +3.12 V, max = +3.46 V) +5V: +5.05 V (min = +4.73 V, max = +5.24 V) +12V: +11.43 V (min = +10.76 V, max = +13.19 V) -12V (reserved): -11.94 V (min = -0.00 V, max = -0.00 V) -5V (reserved): -5.01 V (min = -0.00 V, max = -0.00 V) CPU Fan: 2311 RPM (min = 1997 RPM, div = 4) M/B Temp: +32°C (high = +45°C, hyst = +40°C) CPU Temp (Intel): +32°C (high = +60°C, hyst = +50°C) vid: +1.350 V alarms: johannes-02:/etc # sensors -v sensors version 2.8.6 ########################################### liegt das an sensors, an der Version, oder muß ich damit leben? Danke und Gruß Johannes