Am Dienstag, 18. Januar 2005 20:23 schrieb Oli B.:
Hallo Lutz,
hier die Ausgabe von 'iwconfig eth1':
eth1 IEEE 802.11-DS ESSID:"Hugole" Mode:Managed Frequency:2.437 GHz Access Point: 00:04:0E:25:5B:96 Bit Rate:11 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=35/100 Noise level=0/0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:18 So siehts bei mir aus wlan0 IEEE 802.11g ESSID:"WLAN" Nickname:"uranus" Mode:Managed Frequency:2.462 GHz Access Point: 00:0C:F6:08:03:DF Bit Rate=36 Mb/s Tx-Power:20 dBm Sensitivity=-120 dBm RTS thr=2347 B Fragment thr=2346 B Encryption key:off Power Management:off Link Quality:84/100 Signal level:-84 dBm Noise level:-256 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9624 Invalid misc:11202 Missed beacon:0
Der einzige Unterschied nach 'rcnetwork restart' ist folgende Zeile:
Link Quality=66/100 Signal level=34/100 Noise level=0/0
Die Ausgabe von ifconfig und netstat habe ich jetzt gerade nicht zur Hand, aber die waren vorher und nachher identisch.
Ich hab das mal bei mir durchgespielt. Wenn ich eth0 (feste IP) und Wlan0 (DHCP) aktiviere gehts bei mir auch nicht. Wenn ich alles anhalte und dann nur die Wlan0 starte geht alles. Bei netstat kommt dies raus ernel IP Routentabelle Ziel Router Genmask Flags MSS Fenster irtt Iface 192.168.123.0 * 255.255.255.0 U 0 0 0 wlan0 link-local * 255.255.0.0 U 0 0 0 wlan0 loopback * 255.0.0.0 U 0 0 0 lo default 192.168.123.254 0.0.0.0 UG 0 0 0 wlan0 vergleich doch mal ob du auch einen default Eintrag hast Gruß Lutz
Lutz Weber wrote: ...
Ich hab das mal bei mir durchgespielt. Wenn ich eth0 (feste IP) und Wlan0 (DHCP) aktiviere gehts bei mir auch nicht. Wenn ich alles anhalte und dann nur die Wlan0 starte geht alles.
ich hab nur eth1 aktiviert, ohne DHCP
Bei netstat kommt dies raus
ernel IP Routentabelle Ziel Router Genmask Flags MSS Fenster irtt Iface 192.168.123.0 * 255.255.255.0 U 0 0 0 wlan0 link-local * 255.255.0.0 U 0 0 0 wlan0 loopback * 255.0.0.0 U 0 0 0 lo default 192.168.123.254 0.0.0.0 UG 0 0 0 wlan0
vergleich doch mal ob du auch einen default Eintrag hast
da steht bei mir die Adresse des Routers. Ich denke auch, dass das Netzwerk richtig konfiguriert ist und das Problem die Karte bzw. der atmel-Treiber ist. Wenn ich mich unter X11 abmelde (Sitzung beenden), sehe ich anschließend im Login-Schirm die Meldung kernel: eth1: failed to contact MAC Symptome sind dann die gleichen. iwconfig zeigt mir die Karte (allerdings mit Link Quality=0/100), ping tut nicht. Weiß jemand, was die obige Fehlermeldung bedeutet? Ein 'iwconfig eth1 commit' reanimiert übrigens die Karte wieder. Das Problem scheint mir im Zusammenspiel mit meinem Notebook (IBM-A22M) und der WLAN-Karte (atmel-Treiber) zu liegen - auf meinen Geschäftsnotebook (IBM-T41) trat dieser Effekt mit der PCMCIA-Karte nie auf. mfg oli b. -- Oliver Böhm mailto:boehm@javatux.de http://www.javatux.de
participants (2)
-
Lutz Weber
-
Oli B.