Am Dienstag, 26. April 2011, 09:43:06 schrieb Martin Schröder:

Am 26. April 2011 09:29 schrieb Dr. Dietmar Köppe <Dietmar.Koeppe@gfqs.de>:

...

Was will der Kernel mir damit sagen?

Kabel oder HDD machen Probleme. Was sagt smartctl?

Habe mal auf jeder Platte "test=short" laufen lassen. sda meldet Fehler, aber anscheinend aus der frühen Jugend (life time = 7 h). Oder sehe ich das falsch? Kopiere die Reports für sda und sdb mal ans Ende dieser Mail.

...

Sollte ich schon mal Rücklagen für eine neue HD bilden?

Du hast Backups?

Gut, dass man das Erröten nicht in einer Mail sehen kann. In der Mache ... Danke Dietmar

Gruß Martin

--------------- gf01:/home/kod # smartctl --all /dev/sda smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (openSUSE RPM) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K320 series Device Model: Hitachi HTS543232L9A300 Serial Number: 081023FB2406LECKYUDC Firmware Version: FB4OC40C User Capacity: 320.072.933.376 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3f Local Time is: Tue Apr 26 10:16:47 2011 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 127) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 253 253 033 Pre-fail Always - 0 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1444 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 082 082 000 Old_age Always - 8058 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1439 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 20 193 Load_Cycle_Count 0x0012 051 051 000 Old_age Always - 498966 194 Temperature_Celsius 0x0002 148 148 000 Old_age Always - 37 (Lifetime Min/Max 0/50) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 16 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 16 occurred at disk power-on lifetime: 7 hours (0 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 81 15 43 e0 Error: IDNF at LBA = 0x00431581 = 4396417 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 24 03 01 81 15 43 e0 00 00:08:45.900 READ SECTOR(S) EXT 25 03 01 81 15 43 e0 00 00:08:45.500 READ DMA EXT ef 03 46 ff ff 00 e0 00 00:05:03.100 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:05:03.100 SET FEATURES [Set transfer mode] c6 ff 10 ff ff 00 e0 00 00:05:03.100 SET MULTIPLE MODE Error 15 occurred at disk power-on lifetime: 7 hours (0 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 81 15 43 e0 Error: IDNF 1 sectors at LBA = 0x00431581 = 4396417 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 03 01 81 15 43 e0 00 00:08:45.500 READ DMA EXT ef 03 46 ff ff 00 e0 00 00:05:03.100 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:05:03.100 SET FEATURES [Set transfer mode] c6 ff 10 ff ff 00 e0 00 00:05:03.100 SET MULTIPLE MODE 10 ff 00 47 25 c2 e0 00 00:05:03.000 RECALIBRATE [OBS-4] Error 14 occurred at disk power-on lifetime: 7 hours (0 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 81 15 43 e0 Error: IDNF at LBA = 0x00431581 = 4396417 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 24 ff 01 81 15 43 e0 00 00:05:02.900 READ SECTOR(S) EXT 25 ff 01 81 15 43 e0 00 00:05:02.800 READ DMA EXT 25 ff 08 00 08 a0 e0 00 00:05:02.800 READ DMA EXT 25 ff 08 88 ec 9b e0 00 00:05:02.800 READ DMA EXT 25 ff 03 85 ec 9b e0 00 00:05:02.800 READ DMA EXT Error 13 occurred at disk power-on lifetime: 7 hours (0 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 81 15 43 e0 Error: IDNF 1 sectors at LBA = 0x00431581 = 4396417 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 ff 01 81 15 43 e0 00 00:05:02.800 READ DMA EXT 25 ff 08 00 08 a0 e0 00 00:05:02.800 READ DMA EXT 25 ff 08 88 ec 9b e0 00 00:05:02.800 READ DMA EXT 25 ff 03 85 ec 9b e0 00 00:05:02.800 READ DMA EXT 25 ff 53 32 ec 9b e0 00 00:05:02.800 READ DMA EXT Error 12 occurred at disk power-on lifetime: 7 hours (0 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 81 15 43 e0 Error: IDNF at LBA = 0x00431581 = 4396417 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 24 03 01 81 15 43 e0 00 00:05:00.100 READ SECTOR(S) EXT 25 03 01 81 15 43 e0 00 00:04:59.700 READ DMA EXT ef 03 46 ff ff 00 e0 00 00:01:17.200 SET FEATURES [Set transfer mode] ef 03 0c ff ff 00 e0 00 00:01:17.200 SET FEATURES [Set transfer mode] c6 ff 10 ff ff 00 e0 00 00:01:17.200 SET MULTIPLE MODE SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8058 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ----------------- gf01:/home/kod # smartctl --all /dev/sdb smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (openSUSE RPM) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA family Device Model: WDC WD3200BEVT-22ZCT0 Serial Number: WD-WXEY08PH0421 Firmware Version: 11.01A11 User Capacity: 320.072.933.376 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Apr 26 10:12:21 2011 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 186 184 021 Pre-fail Always - 1675 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1443 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7993 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1438 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 37 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 302235 194 Temperature_Celsius 0x0022 102 089 000 Old_age Always - 45 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7993 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org

Am Dienstag, 26. April 2011 10:29 schrieb Dr. Dietmar Köppe: Hallo Dietmar, die Ursache für die Meldungen habt Ihr anscheinend schon an einer anderen Stelle identifiziert. Mir ist allerdings etwas anderes aufgefallen:

0 9 Power_On_Hours 0x0012 082 082 000 Old_age Always - 8058 [...] 193 Load_Cycle_Count 0x0012 051 051 000 Old_age Always - 498966

Zu dem LOAD_CYCLE_COUNT gab es bereits früher Threads auf dieser Liste. Der Wert ist sehr hoch. Hitachi scheint hierfür 600.00 zu spezifizieren. Darum solltest Du Dich mal kümmern. Grüße Ralf -- Antworten bitte nur in die Mailingliste! PMs bitte an: listpm (@) arndt-de (.) eu -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org

Am Donnerstag, 28. April 2011 16:55 schrieb Dr. Dietmar Köppe:

Hallo Ralf,

vielen Dank für den guten Hinweis.

Der Film läuft wohl unter den Titel: "Der grüne Tod" ;-)

Habe mal in boot.local 'hdparm -B 254' eingetragen und werde nun die Entwicklung des Load Cycle Counts mal etwas aufmerksamer verfolgen.

Schau Dir mal das Paket storage-fixup an. Ich habe hier unter OpenSUSE 11.4 die Version 0.2-35.1. Wenn es installiert ist, steht die Konfiguration in der Datei /etc/storage-fixup.conf. In dem einleitenden Kommentar findest Du einige Hinweise zum Umgang. Bei mir ist Dein HD Typ bereits für 3 Rechner Modelle eingetragen. Hier die entsprechenden Absätze: # Reported drive model: Hitachi HTS543232L9A300 rule dell-inspiron-1705 dmi system-manufacturer Dell Inc. dmi system-product-name MP061 ata model Hitachi HTS5432* act hdparm -B 255 $DEV # Reported drive model: Hitachi HTS543225L9A300 rule acer-aspire-2930z dmi system-manufacturer Acer dmi system-product-name Aspire 2930Z ata model Hitachi HTS5432* act hdparm -B 255 $DEV # Reported drive model: Hitachi HTS543216L9SA00 rule asus-1005ha dmi system-manufacturer ASUSTeK Computer INC. dmi system-product-name 1005HA ata model Hitachi HTS5432* act hdparm -B 254 $DEV Also zweimal 255 und einmal 254

Anderfalls ist die zugesicherte Lebenserwartung von fünf Jahren wohl schon nach zwei Jahren erreicht.

Das könnte schon sein. Ich war jedenfalls damals froh, durch einen Thread hier auf das mir unbekannte Problem gestoßen zu sein. Meine Notebook/HD Kombination ist mittlerweile in der aktuellen Version von storage-fixup bekannt. Schicke für andere dann auch Deine Ergebnisse an die Entwickler. Grüße Ralf -- Antworten bitte nur in die Mailingliste! PMs bitte an: listpm (@) arndt-de (.) eu -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org

Am Dienstag, 26. April 2011, 11:43:52 schrieb David Haller:

Hallo,

Am Tue, 26 Apr 2011, Dr. Dietmar Köppe schrieb:

...

Seit kurzem taucht in /var/log/messages periodisch folgende Sequenz auf: Apr 26 09:08:28 gf01 kernel: [ 379.451687] ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 Apr 26 09:08:28 gf01 kernel: [ 379.451690] ata2.00: irq_stat 0x40000001 Apr 26 09:08:28 gf01 kernel: [ 379.451692] ata2: SError: { HostInt 10B8B } Apr 26 09:08:28 gf01 kernel: [ 379.451694] sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Apr 26 09:08:28 gf01 kernel: [ 379.451702] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Apr 26 09:08:28 gf01 kernel: [ 379.451703] res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) Apr 26 09:08:28 gf01 kernel: [ 379.451706] ata2.00: status: { DRDY ERR } Apr 26 09:08:28 gf01 kernel: [ 379.451711] ata2: hard resetting link Apr 26 09:08:28 gf01 kernel: [ 379.909331] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 26 09:08:28 gf01 kernel: [ 379.913071] ata2.00: configured for UDMA/100 Apr 26 09:08:28 gf01 kernel: [ 379.913300] ata2: EH complete

Scheint um das CD/DVD Laufwerk zu gehen, zeig mal die Ausgabe von lsscsi und such mal vom Anfang her nach 'ata2' in 'dmesg | less'.

gf01:/home/kod # lsscsi [0:0:0:0] disk ATA Hitachi HTS54323 FB4O /dev/sda [1:0:0:0] cd/dvd Optiarc BD ROM BC-5500S 1.B2 /dev/sr0 [4:0:0:0] disk ATA WDC WD3200BEVT-2 11.0 /dev/sdb 'ata2' kommt häufiger vor: gf01:/home/kod # dmesg | grep ata2 | wc -l 3402 Die ersten paar Zeilen aus 'dmesg | less': a2: EH complete [ 1615.451156] ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 [ 1615.451164] ata2.00: irq_stat 0x40000001 [ 1615.451171] ata2: SError: { HostInt 10B8B } [ 1615.451177] sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 [ 1615.451200] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 1615.451203] res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) [ 1615.451210] ata2.00: status: { DRDY ERR } [ 1615.451221] ata2: hard resetting link [ 1615.911248] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1615.915249] ata2.00: configured for UDMA/100 [ 1615.915462] ata2: EH complete [ 1621.451521] ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 [ 1621.451529] ata2.00: irq_stat 0x40000001 [ 1621.451536] ata2: SError: { HostInt 10B8B } [ 1621.451542] sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 [ 1621.451565] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 1621.451568] res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) [ 1621.451575] ata2.00: status: { DRDY ERR } [ 1621.451586] ata2: hard resetting link [ 1621.909062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1621.913090] ata2.00: configured for UDMA/100 [ 1621.913295] ata2: EH complete [ 1639.451329] ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 [ 1639.451337] ata2.00: irq_stat 0x40000001 [ 1639.451344] ata2: SError: { HostInt 10B8B } [ 1639.451350] sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 [ 1639.451373] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 1639.451376] res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error) [ 1639.451383] ata2.00: status: { DRDY ERR } [ 1639.451394] ata2: hard resetting link [ 1639.909567] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Dank für den Hinweis auf 'sr'. Dies könnte erklären, warum ich in den letzten Tagen soviele Brennabbrüche hatte (mit - ich meine mich zu erinnern - Fehler 254).

Bei mir z.B.: [ 4.436678] ata17.00: ATAPI: HL-DT-STDVD-RAM [ 4.473329] scsi 16:0:0:0: CD-ROM HL-DT-ST DVD-RAM [ 4.473748] scsi 16:0:0:0: Attached scsi generic sg9 type 5 [ 6.193180] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 6.193315] Uniform CD-ROM driver Revision: 3.20 [ 6.193634] sr 16:0:0:0: Attached scsi CD-ROM sr0

Bei Festplatten kommt 'sd' statt 'sr'.

...

Sollte ich schon mal Rücklagen für eine neue HD bilden?

Nicht unbedingt. Nach dem smartctl sind die noch ok.

-dnh

-- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org

Am Dienstag, 26. April 2011, 16:28:37 schrieb David Haller:

Hallo,

Am Tue, 26 Apr 2011, Dr. Dietmar Köppe schrieb:

...

Am Dienstag, 26. April 2011, 11:43:52 schrieb David Haller:

...

Scheint um das CD/DVD Laufwerk zu gehen, zeig mal die Ausgabe von lsscsi und such mal vom Anfang her nach 'ata2' in 'dmesg | less'.

gf01:/home/kod # lsscsi [0:0:0:0] disk ATA Hitachi HTS54323 FB4O /dev/sda [1:0:0:0] cd/dvd Optiarc BD ROM BC-5500S 1.B2 /dev/sr0 [4:0:0:0] disk ATA WDC WD3200BEVT-2 11.0 /dev/sdb

Ok, also dein BD-ROM ist 'SCSI 1:0:0:0'.

...

Die ersten paar Zeilen aus 'dmesg | less': a2: EH complete [ 1615.451156] ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x6 [ 1615.451164] ata2.00: irq_stat 0x40000001 [ 1615.451171] ata2: SError: { HostInt 10B8B } [ 1615.451177] sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 [ 1615.451200] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 1615.451203] res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error)

Dank für den Hinweis auf 'sr'. Dies könnte erklären, warum ich in den letzten Tagen soviele Brennabbrüche hatte (mit - ich meine mich zu erinnern - Fehler 254).

Guck weiter oben bzw. in /var/log/boot.msg, da solltest du die Verbindung von ata2.00 zu scsi: 1:0:0:0 bzw. sr0 finden, vergleiche nochmal wie's bei mir ausschaut (auch die Zeit sollte ungefähr ähnlich sein, also in den ersten 10s oder so jedenfalls).

...

...

Bei mir z.B.: [ 4.436678] ata17.00: ATAPI: HL-DT-STDVD-RAM [ 4.473329] scsi 16:0:0:0: CD-ROM HL-DT-ST DVD-RAM [ 4.473748] scsi 16:0:0:0: Attached scsi generic sg9 type 5 [ 6.193180] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 6.193315] Uniform CD-ROM driver Revision: 3.20 [ 6.193634] sr 16:0:0:0: Attached scsi CD-ROM sr0

Bei dir müßte also ungefähr folggendes auftauchen:

[ 4.436678] ata2.00: ATAPI: Optiarc BD ROM BC-5500S [ 4.473329] scsi 1:0:0:0: CD-ROM Optiarc BD ROM BC-5500S [ 6.193634] sr 1:0:0:0: Attached scsi CD-ROM sr0

So ist es ... [ 3.280361] ata2.00: ATAPI: Optiarc BD ROM BC-5500S, 1.B2, max UDMA/100 [ 3.286854] ata2.00: configured for UDMA/100 [ 3.302918] scsi 1:0:0:0: CD-ROM Optiarc BD ROM BC-5500S 1.B2 PQ: 0 ANSI: 5 [ 11.480791] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 11.480883] sr 1:0:0:0: Attached scsi CD-ROM sr0 Frage: ist das nun ein HW - Fehler oder kann ich eine Konfiguration so anpassen, dass mir diese Meldungen nicht weiter die Logs aufblähen? Mit Dank und Gruß Dietmar

Mit abweichenden Zeitstempeln natürlich, damit hättest du aber die Verbindung von ata2.00 zum BD-ROM "festgenagelt" ;)

HTH, -dnh

-- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org