Hallo zusammen, Heute hat sich SMART mit: "Currently unreadable (pending) sectors" gemeldet und gleich darauf den error counter von 0 auf 6 erhöht. Der empfohlene Test (kurz-Version) brachte die Mitteilung: # 1 Extended offline Completed: servo/seek failure 90% 506 - Im Augenblick bin ich dabei, meine Daten von dem Laufwerk zu sichern, weil ich fürchte, dass sich das Teil gerade verabschiedet. Ist diese Annahme richtig, oder gerate ich grundlos in Panik? Hier noch die Ausgabe von smartctl -a: smartctl 5.39 2008-05-08 21:56 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-8 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: SAMSUNG HD103UJ Serial Number: S13PJ1CQ715603 Firmware Version: 1AA01113 User Capacity: 1,000,204,886,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Sat Nov 29 18:06:44 2008 CET ==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 105) The previous self-test completed having the servo (and/or seek) element of the test failed. Total time to complete Offline data collection: (11775) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 197) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 26 3 Spin_Up_Time 0x0007 076 076 011 Pre-fail Always - 8080 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 176 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 2 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 10179 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 507 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 6 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 176 13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 6 183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 184 Unknown_Attribute 0x0033 100 100 099 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 6 188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 079 077 000 Old_age Always - 21 (Lifetime Min/Max 13/21) 194 Temperature_Celsius 0x0022 079 076 000 Old_age Always - 21 (Lifetime Min/Max 13/22) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 9418369 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 099 099 000 Old_age Always - 7 SMART Error Log Version: 1 ATA Error Count: 6 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 96 a6 08 e7 Error: UNC at LBA = 0x0708a696 = 118007446 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 96 a6 08 e7 0a 05:39:34.740 READ DMA ec 00 00 00 00 00 a0 0a 05:39:34.730 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 05:39:34.730 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 0a 05:39:34.720 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 05:39:34.230 NOP [Abort queued commands] Error 5 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 96 51 00 96 a6 08 e7 Error: ICRC, IDNF, ABRT, NM at LBA = 0x0708a696 = 118007446 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 96 a6 08 e7 0a 05:39:33.350 READ DMA ec 00 00 00 00 00 a0 0a 05:39:33.340 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 05:39:33.340 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 0a 05:39:32.690 IDENTIFY DEVICE Error 4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 96 a6 08 e7 Error: UNC at LBA = 0x0708a696 = 118007446 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 96 a6 08 e7 0a 05:39:31.870 READ DMA ec 00 00 00 00 00 a0 0a 05:39:31.860 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 05:39:31.860 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 0a 05:39:31.040 IDENTIFY DEVICE Error 3 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 96 a6 08 e7 Error: UNC at LBA = 0x0708a696 = 118007446 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 96 a6 08 e7 0a 05:39:28.330 READ DMA ec 00 00 00 00 00 a0 0a 05:39:28.320 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 05:39:28.320 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 0a 05:39:27.470 IDENTIFY DEVICE Error 2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 96 a6 08 e7 Error: UNC at LBA = 0x0708a696 = 118007446 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 96 a6 08 e7 0a 05:39:24.670 READ DMA ec 00 00 00 00 00 a0 0a 05:39:24.650 IDENTIFY DEVICE ef 03 46 00 00 00 a0 0a 05:39:24.650 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 0a 05:39:21.750 IDENTIFY DEVICE SMART Self-test log structure revision number 0 Warning: ATA Specification requires self-test log structure revision number = 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: servo/seek failure 90% 506 - # 2 Short offline Aborted by host 90% 506 - # 3 Extended offline Aborted by host 10% 505 - # 4 Short offline Aborted by host 00% 498 - # 5 Short offline Aborted by host 00% 486 - # 6 Short offline Aborted by host 00% 479 - # 7 Short offline Aborted by host 00% 469 - # 8 Short offline Aborted by host 00% 459 - # 9 Short offline Aborted by host 00% 447 - #10 Short offline Aborted by host 00% 438 - #11 Extended offline Aborted by host 00% 436 - #12 Short offline Aborted by host 00% 430 - #13 Short offline Aborted by host 00% 419 - #14 Short offline Aborted by host 00% 410 - #15 Short offline Aborted by host 00% 397 - #16 Short offline Aborted by host 00% 390 - #17 Short offline Aborted by host 00% 381 - #18 Short offline Aborted by host 00% 372 - #19 Extended offline Aborted by host 00% 370 - #20 Short offline Aborted by host 00% 363 - #21 Short offline Aborted by host 00% 353 - SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 SMART Selective self-test log data structure revision number 0 Warning: ATA Specification requires selective self-test log data structure revision number = 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Vielen Dank für eure Hilfe und noch ein schönes Wochenende. Mit freundlichen Grüßen Uwe Diederich -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org