Seit Update auf 6.4 kein Internet Zugang mehr... :-(
Hallo! Da heißt es, never change a running system - habe ich aber doch, nämlich ein Update von SuSE 6.3. auf 6.4 vorgenommen. Das Ergebnis war zunächst, daß ich mit dem installierten Standardkernel zwar über kppp eine Verbindung zu meinem Provider aufbauen konnte, diese aber "irgendwie nicht richtig funktionierte". Mit kpppload wurde eine Bandbreite von 1k angezeigt und auch minimalster Traffic angezeigt (z.B. beim Versuch, Mails abzurufen). Auch über wvdial dasselbe Problem. Ein Download der Mails war nicht möglich, Aufrufen von Websites auch nicht. Obwohl ich nichts verändert habe (außer dem Update natürlich), habe ich ein Routing Problem vermutet, konnte aber nichts finden. Das war das Ergebnis von netstat: bash-2.03# netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 193.101.111.20 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 172.20.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo und dies meines Ping-Versuchs: bash-2.03# ping 193.101.111.20 PING 193.101.111.20 (193.101.111.20): 56 data bytes 64 bytes from 193.101.111.20: icmp_seq=0 ttl=251 time=182.528 ms 64 bytes from 193.101.111.20: icmp_seq=1 ttl=251 time=170.021 ms 64 bytes from 193.101.111.20: icmp_seq=2 ttl=251 time=170.017 ms 64 bytes from 193.101.111.20: icmp_seq=3 ttl=251 time=170.018 ms 64 bytes from 193.101.111.20: icmp_seq=4 ttl=251 time=160.020 ms 64 bytes from 193.101.111.20: icmp_seq=5 ttl=251 time=160.021 ms 64 bytes from 193.101.111.20: icmp_seq=6 ttl=251 time=160.020 ms 64 bytes from 193.101.111.20: icmp_seq=7 ttl=251 time=160.018 ms 64 bytes from 193.101.111.20: icmp_seq=8 ttl=251 time=160.019 ms 64 bytes from 193.101.111.20: icmp_seq=9 ttl=251 time=160.021 ms 64 bytes from 193.101.111.20: icmp_seq=10 ttl=251 time=150.021 ms 64 bytes from 193.101.111.20: icmp_seq=11 ttl=251 time=160.021 ms 64 bytes from 193.101.111.20: icmp_seq=12 ttl=251 time=160.021 ms 64 bytes from 193.101.111.20: icmp_seq=13 ttl=251 time=160.019 ms 64 bytes from 193.101.111.20: icmp_seq=14 ttl=251 time=150.017 ms 64 bytes from 193.101.111.20: icmp_seq=15 ttl=251 time=150.019 ms 64 bytes from 193.101.111.20: icmp_seq=16 ttl=251 time=150.013 ms 64 bytes from 193.101.111.20: icmp_seq=17 ttl=251 time=150.020 ms 64 bytes from 193.101.111.20: icmp_seq=18 ttl=251 time=170.017 ms --- 193.101.111.20 ping statistics --- 19 packets transmitted, 19 packets received, 0% packet loss round-trip min/avg/max = 150.013/160.677/182.528 ms bash-2.03# Da ich sowieso mit der Performance des Standard-Kernels nicht zufrieden war, dachte ich, daß sich das Problem bestimmt beheben ließe, wenn ich einen neuen Kernel "backe". Was ich auch tat. Mit dem Ergebnis, daß nun beim Aufruf von kppp die Meldung kommt "Sorry, Modem besetzt". Auf der Console erscheint nach dem Booten die folgende Fehlermeldung: pppd [235] no device specified and stdin is not a tty Nun fällt mir dazu gar nichts mehr ein, weil ich exakt die Kernel-Konfiguration eingestellt habe, die ich unter SuSE 6.3 ebenfalls mit Kernel 2.2.14 hatte. Wäre super, wenn mich jemand auf die richtige Fährte setzen könnte, denn ich kann zwar immer noch über Windoze ins Netz, will ich aber nicht. Ich hänge außerdem unten die Meldungen aus /var/log/boot.msg an, vielleicht hilft das ja bei der Auflösung dieses Problems, das mich nun seit einer Woche von anderen Dingen abhält. :-( Vielen Dank! Birgit Inspecting /boot/System.map-2.2.14 Loaded 8963 symbols from /boot/System.map-2.2.14. Symbols match kernel version 2.2.14. No module symbols loaded. klogd 1.3-3, log source = ksyslog started. <4>Linux version 2.2.14 (root@harlekin) (gcc version 2.95.2 19991024 (release)) #4 Tue Apr 11 22:03:41 CEST 2000 <4>Detected 501147490 Hz processor. <4>Console: colour VGA+ 80x25 <4>Calibrating delay loop... 999.42 BogoMIPS <4>Memory: 127784k/131008k available (1188k kernel code, 412k reserved, 1556k data, 68k init, 0k bigmem) <4>Dentry hash table entries: 16384 (order 5, 128k) <4>Buffer cache hash table entries: 131072 (order 7, 512k) <4>Page cache hash table entries: 32768 (order 5, 128k) <4>CPU: Intel Pentium III (Katmai) stepping 03 <6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting. <6>Checking 'hlt' instruction... OK. <4>POSIX conformance testing by UNIFIX <4>PCI: PCI BIOS revision 2.10 entry at 0xf08b0 <4>PCI: Using configuration type 1 <4>PCI: Probing PCI hardware <6>Linux NET4.0 for Linux 2.2 <6>Based upon Swansea University Computer Society NET3.039 <6>NET4: Unix domain sockets 1.0 for Linux NET4.0. <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP <4>TCP: Hash tables configured (ehash 131072 bhash 65536) <4>Initializing RT netlink socket <4>Starting kswapd v 1.5 <6>parport0: PC-style at 0x378 (0x778) [SPP,ECP,ECPEPP,ECPPS2] <4>parport0: detected irq 7; use procfs to enable interrupt-driven operation. <7>parport_probe: succeeded <6>parport0: Printer, HEWLETT-PACKARD DESKJET 895C <6>Detected PS/2 Mouse Port. <6>Serial driver version 4.27 with no serial options enabled <6>ttyS00 at 0x03f8 (irq = 4) is a 16550A <6>ttyS01 at 0x02f8 (irq = 3) is a 16550A <4>pty: 256 Unix98 ptys configured <6>Registering PPPoE driver <6>lp0: using parport0 (polling). <6>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.12) <6>Real Time Clock Driver v1.09 <6>Uniform Multi-Platform E-IDE driver Revision: 6.30 <4>ide: Assuming 40MHz system bus speed for PIO modes; override with idebus=xx <4>PIIX4: IDE controller on PCI bus 00 dev 21 <4>PIIX4: not 100% native mode: will probe irqs later <4> ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio <4> ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio <4>hda: IBM-DJNA-352030, ATA DISK drive <4>hdc: CD-540E, ATAPI CDROM drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <4>ide1 at 0x170-0x177,0x376 on irq 15 <6>hda: IBM-DJNA-352030, 19470MB w/1966kB Cache, CHS=2482/255/63, UDMA(33) <4>hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33) <6>Uniform CDROM driver Revision: 2.56 <6>Floppy drive(s): fd0 is 1.44M <6>FDC 0 is a post-1991 82077 <6>ncr53c8xx: at PCI bus 0, device 11, function 0 <6>ncr53c8xx: 53c875E detected with Tekram NVRAM <6>ncr53c875E-0: rev=0x26, base=0xe0000000, io_port=0xb800, irq=10 <6>ncr53c875E-0: Tekram format NVRAM, ID 7, Fast-20, Parity Checking <6>ncr53c875E-0: on-chip RAM at 0xdf800000 <6>ncr53c875E-0: restart (scsi reset). <4>ncr53c875E-0: Downloading SCSI SCRIPTS. <4>scsi0 : ncr53c8xx - version 3.2a-2 <4>scsi : 1 host. <4> Vendor: YAMAHA Model: CRW6416S Rev: 1.0c <4> Type: CD-ROM ANSI SCSI revision: 02 <4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 <4>scsi : detected 1 SCSI cdrom total. <6>ncr53c875E-0-<1,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 15) <4>sr0: scsi3-mmc drive: 16x/16x writer cd/rw xa/form2 cdda tray <6>PPP: version 2.3.7 (demand dialling) <6>TCP compression code copyright 1989 Regents of the University of California <6>PPP line discipline registered. <6>ne2k-pci.c:vpre-1.00e 5/27/99 D. Becker/P. Gortmaker http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html <4>ne2k-pci.c: PCI NE2000 clone 'RealTek RTL-8029' at I/O 0xb400, IRQ 5. <4>eth0: RealTek RTL-8029 found at 0xb400, IRQ 5, 00:E0:7D:79:2D:0D. <4>Partition check: <4> hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 > <5>NTFS version 990411 <4>VFS: Mounted root (ext2 filesystem) readonly. <4>Freeing unused kernel memory: 68k freed <6>Adding Swap: 136512k swap-space (priority -1) Kernel logging (ksyslog) stopped. Kernel log daemon terminating. -- Birgit Schultz, M.A. mailto:joker@jester.de http://www.jester.de "This will end your Windows Session!" - I live for those six words. --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Birgit Schultz wrote:
Hallo!
Hallo Birgit! Ohne dass ich Dir wirklich helfen kann (kenne mich mit ppp nicht aus), aber:
... Obwohl ich nichts verändert habe (außer dem Update natürlich), habe ich ein Routing Problem vermutet, konnte aber nichts finden. Imho fehlt in Deinen Routing-Tabellen die default-Route. Eventuell ist ja Dein dummy-Device aktiv (was sagt "/sbin/ifconfig")?
Und wegen "pppd [235] no device specified and stdin is not a tty": Schau auch mal auf http://sdb.suse.de/sdb/de/html/olh_ppp_check.html, vielleicht ist ja da was bei... Rgds. Heiko. -- Nuetzliche Samba-Doku online: http://de.samba.org/samba/docs/ --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Hallo, Birgit Schultz wrote:
Das Ergebnis war zunächst, daß ich mit dem installierten Standardkernel zwar über kppp eine Verbindung zu meinem Provider aufbauen konnte, diese aber "irgendwie nicht richtig funktionierte".
Hast Du evtl. bei "kppp" die Einstellung "Setze die Standardroute auf diesen Gateway" nicht gesetzt?
Das war das Ergebnis von netstat:
bash-2.03# netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 193.101.111.20 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 172.20.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
Es fehlt die Default-Route. Aus irgendwelchen Gruenden (moeglicherweise, weil bei "kppp" das erwaehnte Kontrollkaestchen nicht aktiviert ist), wird keine Default-Route gesetzt. Somit finden Deine Pakete, die Du in Richtung Internet richtest, nicht raus.
und dies meines Ping-Versuchs:
bash-2.03# ping 193.101.111.20 PING 193.101.111.20 (193.101.111.20): 56 data bytes 64 bytes from 193.101.111.20: icmp_seq=0 ttl=251 time=182.528 ms 64 bytes from 193.101.111.20: icmp_seq=1 ttl=251 time=170.021 ms 64 bytes from 193.101.111.20: icmp_seq=2 ttl=251 time=170.017 ms
Klar, Deine direkte "ppp"-Gegenstelle erreichst Du, denn dafuer ist ja auch keine Default-Route noetig. Gruss, Steffen --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
participants (3)
-
heiko.degenhardt@sentec-elektronik.de
-
joker@jester.de
-
moser@egu.schule.ulm.de