Kernel 2.6.7 <6>APIC error on CPU0: 04(04)
Hallo alle zusammen!
Ich habe ein großes Problem. Auf meinem ASUS A7M266-D mit 2 AMD 2800+ MP
versuche ich gerade den 2.6.7 Kernel zum laufen zu kriegen. Aus irgend
einem Grund gibt er beim Boot einen APIC error aus und aktiviert nur
eine der beiden CPUs. Anbei seht Ihr die boot.msg. Ich bin mittlerweile
echt schon verzweifelt!!
Vielen Dank schon mal im Voraus für jede Hilfe
Michael
Inspecting /boot/System.map-2.6.7
Loaded 23315 symbols from /boot/System.map-2.6.7.
Symbols match kernel version 2.6.7.
No module symbols loaded - kernel modules not enabled.
klogd 1.4.1, log source = ksyslog started.
)
<6>APIC error on CPU0: 04(04)
<6>APIC error on CPU0: 04(04)
<6>APIC error on CPU0: 04(04)
<6>APIC error on CPU0: 04(04)
....
....
<6>APIC error on CPU0: 00(04)
<6>APIC error on CPU0: 04(04)
<6>APIC error on CPU0: 00(04)
<4>Not responding.
<4>CPU #1 not responding - cannot use it.
<6>Total of 1 processors activated (4194.30 BogoMIPS).
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 2133.0007 MHz.
<4>..... host bus clock speed is 266.0625 MHz.
<4>Brought up 1 CPUs
<7>CPU0: online
<7> domain 0: span 00000001
<7> groups: 00000001
<7> domain 1: span 00000001
<7> groups: 00000001
<6>checking if image is initramfs...it isn't (no cpio magic); looks like
an initrd
<6>Freeing initrd memory: 1397k freed
<6>NET: Registered protocol family 16
<6>PCI: PCI BIOS revision 2.10 entry at 0xf1f30, last bus=2
<6>PCI: Using configuration type 1
<6>mtrr: v2.0 (20020519)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<4>PCI: Probing PCI hardware
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Using IRQ router AMD768 [1022/7443] at 0000:00:07.3
<6>vesafb: framebuffer at 0xe0000000, mapped to 0xf8800000, size 5120k
<6>vesafb: mode is 1280x1024x16, linelength=2560, pages=50
<6>vesafb: protected mode interface info at c000:56fd
<6>vesafb: scrolling: redraw
<6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
<6>fb0: VESA VGA frame buffer device
<6>Simple Boot Flag at 0x3a set to 0x1
<6>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
<4>highmem bounce pool size: 64 pages
<4>Total HugeTLB memory allocated, 0
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>SELinux: Registering netfilter hooks
<6>Initializing Cryptographic API
<4>BIOS failed to enable PCI standards compliance, fixing this error.
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<4>Console: switching to colour frame buffer device 160x64
<6>Real Time Clock Driver v1.12
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
enabled
<4>ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<4>ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
<4>Using anticipatory io scheduler
<4>floppy0: no floppy controllers found
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024
blocksize
<6>loop: loaded (max 8 devices)
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
<6>AMD7441: IDE controller at PCI slot 0000:00:07.1
<4>PCI: Enabling device 0000:00:07.1 (0000 -> 0001)
<6>AMD7441: chipset revision 4
<6>AMD7441: not 100%% native mode: will probe irqs later
<6>AMD7441: 0000:00:07.1 (rev 04) UDMA100 controller
<6>AMD7441: neither IDE port enabled (BIOS)
<4>ide-floppy driver 0.99.newide
<6>mice: PS/2 mouse device common for all mice
<6>input: PC Speaker
<6>serio: i8042 AUX port at 0x60,0x64 irq 12
<6>serio: i8042 KBD port at 0x60,0x64 irq 1
<6>input: AT Translated Set 2 keyboard on isa0060/serio0
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>NET: Registered protocol family 2
<6>IP: routing cache hash table of 8192 buckets, 64Kbytes
<6>TCP: Hash tables configured (established 262144 bind 65536)
<6>NET: Registered protocol family 1
<6>NET: Registered protocol family 8
<6>NET: Registered protocol family 20
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<5>RAMDISK: Compressed image found at block 0
<4>VFS: Mounted root (ext2 filesystem).
<5>SCSI subsystem initialized
<6>AMD756: dev 9005:0080, router pirq : 1 get irq : 11
<6>PCI: Found IRQ 11 for device 0000:00:09.0
<6>IRQ routing conflict for 0000:00:09.0, have irq 10, want irq 11
<6>IRQ routing conflict for 0000:02:06.0, have irq 10, want irq 11
<6>IRQ routing conflict for 0000:02:08.2, have irq 10, want irq 11
<6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<4>
Michael Hammer wrote:
Ich habe ein großes Problem. Auf meinem ASUS A7M266-D mit 2 AMD 2800+ MP versuche ich gerade den 2.6.7 Kernel zum laufen zu kriegen. Aus irgend einem Grund gibt er beim Boot einen APIC error aus und aktiviert nur eine der beiden CPUs. Anbei seht Ihr die boot.msg. Ich bin mittlerweile echt schon verzweifelt!! [...]
Gehts denn mit einem anderen Kernel? Oder ist das mit allen 2.6er Kerneln so? CU, Th.
participants (2)
-
Michael Hammer
-
Thomas Hertweck