Hallo zusammen, Erst mal sorry, ist ganz schön lang geworden, aber ich wollte halt soviel Angaben machen wie ich kann. Nachdem mir alle versicherten die 3Com 515 wäre ein echtes Schätzchen, dachte ich es könnte nicht so schwierig sein, doch leiderbin ich jetzt mit meinem Latein am Ende. Folgende Konfiguration: Suse Linux 6.4 Kernel 2.2.14 1*DLink DFE 530 TX mit via-rhine Modul auf 192.168.10.1 1*3Com 3c515 mit Standard Kernel Modul auf 192.168.10.10 Boote ich das falsche OS auf dem Rechner mit der 3Com geht ein ping munter hin und her. Boote ich dann Linux ist sich nix mit ping. ---Bootmeldungen--- 3c515.c:v0.99 4/7/98 becker@cesdis.gsfc.nasa.gov 3c515 Resource configuraiton register 0x0083, DCR 1483. eth0: 3Com 3c515 at 0x280, 00:a0:24:e0:76:5e, DMA 3, IRQ 3 64K word-wide RAM 1:1 Rx:Tx split, autoselect/10baseT interface. Media override to transceiver type 0 (10baseT). 1 3c515 cards found. device eth0 entered promiscuous mode device eth0 left promiscuous mode Board 1 has Identiy 23 24 e0 76 5e 51 50 6d 50: TCM5051 Serial No 618690142 [checksum 23] TCM5051/618690142[0]{3Com Fast Etherlink ISA}: Port 0x280; IRQ3 DMA3 --- Enabled OK done Setting up network device eth0 done ---/Bootmeldungen/--- ---ifconfig 3com-- eth0 Link encap:Ethernet HWaddr 00:A0:24:E0:76:5E inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:3 Base address:0x280 DMA chan:3 ---/ifconfig 3Com--- ---isapnp.conf--- (READPORT 0x0273) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) (CONFIGURE TCM5051/618690142 (LD 0 (INT 0 (IRQ 3 (MODE +E))) (DMA 0 (CHANNEL 3)) (IO 0 (SIZE 32) (BASE 0x0280) ) (NAME "TCM5051/618690142[0]{3Com Fast EtherLink ISA}") (ACT Y) )) ---/isapnp.conf/--- ---modules.conf--- alias eth0 3c515 options 3c515=4,12 ---modules.conf--- ---/sbin/3c515-diag--- Looking for card at 280. A ISA Fast EtherLink III board was detected at I/O 0x280. Window 0: 0000 0000 0000 0000 0000 0095 0000 0000. Window 1: 0000 3736 0000 2002 8000 00ff 7ffc 2002. Window 2: a000 e024 5e76 0000 0000 0000 00da 4002. Window 3: 001b 0102 0000 0000 f040 7fff 7fff 6002. Window 4: 0000 06d0 2000 0580 0002 8ec0 0000 8002. Window 5: 1ffc 1ffc 00da 1ffc 0007 0298 00da a002. Window 6: 0000 0000 0000 0000 0000 0000 0000 c002. Window 7: 0000 0000 0000 0000 8000 00ff 0000 e002. Operation registers: 3736 3736 0000 e002 8000 00ff 7ffc e002. Boomerang registers: ffff ffff ffff ffff ffff ffff ffff ffff (at 0x680) : ffff ffff ffff ffff ffff ffff ffff ffff. Corkscrew registers: 1483 0083 0000 0000 0001 0197 0048 ffff. ...[kein EEPROM]... 64K word-wide RAM 1:1 Rx:Tx split, autoselect/10baseT interface. Done card at 0x280. ---/sbin/3c515-diag/--- ---cat /proc/*--- interrupts: 3: 0 XT-PIC 3c515 dma: 3: 3c515 ioports: 0280-029f : 3c515 ---/cat /proc/*--- ---Netzwerk Config--- /etc/hosts: 127.0.0.1 localhost lo 194.64.245.65 mail.bielefeld.netsurf.de 192.168.10.1 work.junge-alte.de work 192.168.0.99 syl.junge-alte.de syl 192.168.10.10 syl.junge-alte.de /etc/networks: loopback 127.0.0.0 localnet 192.168.10.0 /etc/route.conf: 192.168.10.0 0.0.0.0 255.255.255.0 eth0 192.168.0.1 0.0.0.0 255.255.255.255 ippp0 default 192.168.0.1 /etc/resolv.conf: search junge-alte.de nameserver 194.122.192.1 ---/Netzwerk Config/--- Die Verbindung läuft über ein gekreutzes TP Kabel ohne Hub. Leider habe ich nur sehr wenig Ahnung von Netzwerkhardware, daher meine Fragen: Irgentetwas auffällig an der Konfiguration/Meldungen? Könnte es sein das die DLink 100 Mbit will und die 3Com nur auf 10 läuft (obwohl die Options Zeile in der modules.conf die Karte eigentlich auf100Mbit schalten sollte)? Kann der unterschiedliche Speed dafür sorgen, dass in ping nicht klappt? Wo gehts weiter? Schonmal dank an alle die sich hierdurchgequält haben ;). -- (o< ----CU //\ *Maik Holtkamp* V_/_ #s-y-l@gmx.net# --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Nochmal hallo, On 00/09/16@14:32 Maik Holtkamp told me in 142lines (4,2K): hatte noch eins vergessen, tcpdump liefert beim laufenden ping auf das Teil: 17:24:44.813919 arp who-has syl.junge-alte.de tell work.junge-alte.de (0:50:ba:6e:d0:8c) Was heisst??? -- Maik Holtkamp s-y-l@gmx.net "Why should I read the fucking manual? I know how to f***!" (unknown Linux-user) --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
Hy, ich habs gefunden :). On 00/09/16@14:32 Maik Holtkamp told me in 146lines (4,3K):
autoselect/10baseT interface. Media override to transceiver type 0 (10baseT). 1 3c515 cards found.
Das war nicht was ich wollte.
---modules.conf--- alias eth0 3c515 options 3c515 options=4,12 ---modules.conf---
Irgentwer (ich glaube nicht das ich das selber war und habe yast in Verdacht;) hatte an die modules.conf noch eine letzte Zeile angefügt: options 3c515 options=0 Ich habe jetzt alle options auskommentiert und es ping wie verrückt. -- *Maik Holtkamp* *s-y-l@gmx.net* The README file said "Requires Windows 95, NT 4.0, or better." So... I installed it on Linux! --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com
participants (1)
-
s-y-l@gmx.net