AW: lm-sensors: Ausgabe sehr mager
Hi, bei der Konfiguration kannst du doch zwischen ISA und PCI Version des Sensors (der auf deinem Motherboard sitzt) wählen. Btw. es kommt mir auch etwas spanisch vor aber gut ;) Du kannst ja mal da umstellen. Vielleicht klappt das dann. Was du aber für Ausgaben bekommst, v.a. das: ->schnipp<- ERROR: Can't get alarm data! ERROR: Can't get beep data! ERROR: Can't get IN0 data! ERROR: Can't get IN2 data! ERROR: Can't get IN3 data! ERROR: Can't get IN4 data! ERROR: Can't get IN5 data! ERROR: Can't get IN6 data! ERROR: Can't get IN7 data! ERROR: Can't get IN8 data! ERROR: Can't get FAN1 data! ERROR: Can't get FAN2 data! ERROR: Can't get TEMP1 data! ERROR: Can't get TEMP2 data! ->schnapp<- zeigt eindeutig dass das lm-sensors deinen Chip nicht findet. Spiel etwas (wie oben gesagt) mit dem Install/Conf Proggie rum. Gruß, Stephan -----Ursprüngliche Nachricht----- Von: bderks@web.de [mailto:bderks@web.de] Gesendet: Dienstag, 11. Juni 2002 20:52 An: suse-linux@suse.com Betreff: lm-sensors: Ausgabe sehr mager Hallo, habe bei mir die letzte lm-sensors Version (2.6.3) installiert, mit neuestem i2c (von gleicher Seite). Auf meiner Kiste (Abit KR7A-133) gibt er folgendes aus: (als user: ) bede@jupp:~ > sensors eeprom-i2c-0-50 Adapter: SMBus Via Pro adapter at 5000 Algorithm: Non-I2C SMBus adapter Memory type: DDR SDRAM DIMM SPD SDRAM Size (MB): 512 eeprom-i2c-0-51 Adapter: SMBus Via Pro adapter at 5000 Algorithm: Non-I2C SMBus adapter Memory type: DDR SDRAM DIMM SPD SDRAM Size (MB): 512 ddcmon-i2c-1-50 Adapter: DDC:fb0 #0 on i2c-matroxfb Algorithm: Bit-shift algorithm Monitor ID: STC032: Serial number: 16843009 Monitor Size (cm): 28x37 Vertical Sync (Hz): 83-97 Horizontal Sync (KHz): 109-112 w83697hf-isa-0290 Adapter: ISA adapter Algorithm: ISA algorithm ERROR: Can't get alarm data! ERROR: Can't get beep data! ERROR: Can't get IN0 data! ERROR: Can't get IN2 data! ERROR: Can't get IN3 data! ERROR: Can't get IN4 data! ERROR: Can't get IN5 data! ERROR: Can't get IN6 data! ERROR: Can't get IN7 data! ERROR: Can't get IN8 data! ERROR: Can't get FAN1 data! ERROR: Can't get FAN2 data! ERROR: Can't get TEMP1 data! ERROR: Can't get TEMP2 data! ---------------------------------------------- Als root gibt er das gleiche aus, abzüglich der ERROR-Zeilen unten. (Kernel 2.4.18), i2c _nicht_ im Kernel fest eincompiliert. Würde aber gerne mal wissen, wie warm es meiner Kiste ist... Bernhard -- Um die Liste abzubestellen, schicken Sie eine Mail an: suse-linux-unsubscribe@suse.com Um eine Liste aller verfügbaren Kommandos zu bekommen, schicken Sie eine Mail an: suse-linux-help@suse.com
participants (1)
-
Stephan Kessler