Hallo Liste! Mit meiner SuSE 9.2 hab ich ein Problem mit meinem Internetzugang. Eingestellt ist es so, das sich meine dsl -Verbindung beim Booten aufbaut. Wenn ich mich dann im KDE einlogge, und bei kinternet nachschaue, habe ich auch eine IP-Adresse von meinem Provider (congster) zugewiesen bekommen. Ich kann dann aber nix anpingen. Ich komme dann einfach nicht ins Internet. Ich beende dann immer die Verbindung und starte sie neu. Dann funzt alles. Der neue Verbindungsaufbau dauert aber auch immer ewig...... Hier ein Auszug aus meiner /var/log/messages : Mar 10 21:25:25 linux exiting on signal 15 Mar 11 07:44:24 linux syslogd 1.4.1: restart. Mar 11 07:44:24 linux pppd[6530]: Plugin rp-pppoe.so loaded. Mar 11 07:44:24 linux pppd[6530]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2 Mar 11 07:44:24 linux pppd[6530]: Plugin passwordfd.so loaded. Mar 11 07:44:24 linux pppd[6530]: pppd 2.4.2 started by root, uid 0 Mar 11 07:44:24 linux pppd[6530]: Renamed interface ppp0 to dsl0 Mar 11 07:44:24 linux pppd[6530]: Using interface dsl0 Mar 11 07:44:24 linux pppd[6530]: Couldn't increase MTU to 1500 Mar 11 07:44:24 linux pppd[6530]: Couldn't increase MRU to 1500 Mar 11 07:44:24 linux pppd[6530]: local IP address 192.168.99.1 Mar 11 07:44:24 linux pppd[6530]: remote IP address 192.168.99.99 Mar 11 07:44:24 linux SuSEfirewall2: Warning: no interface active Mar 11 07:44:25 linux SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Mar 11 07:44:26 linux smpppd[6966]: smpppd version 1.50 started Mar 11 07:44:26 linux ntpd[7007]: ntpd 4.2.0a@1.1190-r Wed Jan 26 17:34:57 UTC 2005 (1) Mar 11 07:44:26 linux ntpd[7007]: precision = 2.000 usec Mar 11 07:44:26 linux ntpd[7007]: Listening on interface wildcard, 0.0.0.0#123 Mar 11 07:44:26 linux ntpd[7007]: Listening on interface wildcard, ::#123 Mar 11 07:44:26 linux ntpd[7007]: Listening on interface lo, 127.0.0.1#123 Mar 11 07:44:26 linux ntpd[7007]: Listening on interface dsl0, 192.168.99.1#123 Mar 11 07:44:26 linux ntpd[7007]: kernel time sync status 0040 Mar 11 07:44:26 linux ntpd[7007]: frequency initialized 0.000 PPM from /var/lib/ntp/drift/ntp.drift Mar 11 07:44:29 linux kernel: klogd 1.4.1, log source = /proc/kmsg started. Mar 11 07:44:29 linux kernel: Linux agpgart interface v0.100 (c) Dave Jones Mar 11 07:44:29 linux kernel: agpgart: Detected VIA KT400/KT400A/KT600 chipset Mar 11 07:44:29 linux kernel: agpgart: Maximum main memory to use for agp memory: 439M Mar 11 07:44:29 linux kernel: agpgart: AGP aperture is 64M @ 0xf8000000 Mar 11 07:44:29 linux kernel: 8139too Fast Ethernet driver 0.9.27 Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 9 (level, low) -> IRQ 9 Mar 11 07:44:29 linux kernel: eth0: RealTek RTL8139 at 0xe125e000, 00:10:a7:1e:6b:c1, IRQ 9 Mar 11 07:44:29 linux kernel: eth0: Identified 8139 chip type 'RTL-8100B/8139D' Mar 11 07:44:29 linux kernel: USB Universal Host Controller Interface driver v2.2 Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 10 (level, low) -> IRQ 10 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.0: UHCI Host Controller Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.0: irq 10, io base 00009000 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 Mar 11 07:44:29 linux kernel: usb usb1: Product: UHCI Host Controller Mar 11 07:44:29 linux kernel: usb usb1: Manufacturer: Linux 2.6.8-24.11-default uhci_hcd Mar 11 07:44:29 linux kernel: usb usb1: SerialNumber: 0000:00:10.0 Mar 11 07:44:29 linux kernel: hub 1-0:1.0: USB hub found Mar 11 07:44:29 linux kernel: hub 1-0:1.0: 2 ports detected Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 10 (level, low) -> IRQ 10 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.1: UHCI Host Controller Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.1: irq 10, io base 00008800 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 Mar 11 07:44:29 linux kernel: usb usb2: Product: UHCI Host Controller Mar 11 07:44:29 linux kernel: usb usb2: Manufacturer: Linux 2.6.8-24.11-default uhci_hcd Mar 11 07:44:29 linux kernel: usb usb2: SerialNumber: 0000:00:10.1 Mar 11 07:44:29 linux kernel: hub 2-0:1.0: USB hub found Mar 11 07:44:29 linux kernel: hub 2-0:1.0: 2 ports detected Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 10 (level, low) -> IRQ 10 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.2: UHCI Host Controller Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.2: irq 10, io base 00008400 Mar 11 07:44:29 linux kernel: usb 1-1: new full speed USB device using address 2 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 Mar 11 07:44:29 linux kernel: usb usb3: Product: UHCI Host Controller Mar 11 07:44:29 linux kernel: usb usb3: Manufacturer: Linux 2.6.8-24.11-default uhci_hcd Mar 11 07:44:29 linux kernel: usb usb3: SerialNumber: 0000:00:10.2 Mar 11 07:44:29 linux kernel: hub 3-0:1.0: USB hub found Mar 11 07:44:29 linux kernel: hub 3-0:1.0: 2 ports detected Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 10 (level, low) -> IRQ 10 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.3: UHCI Host Controller Mar 11 07:44:29 linux kernel: usb 1-1: Product: EPSON Scanner Mar 11 07:44:29 linux kernel: usb 1-1: Manufacturer: EPSON Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.3: irq 10, io base 00008000 Mar 11 07:44:29 linux kernel: uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 Mar 11 07:44:29 linux kernel: usb usb4: Product: UHCI Host Controller Mar 11 07:44:29 linux kernel: usb usb4: Manufacturer: Linux 2.6.8-24.11-default uhci_hcd Mar 11 07:44:29 linux kernel: usb usb4: SerialNumber: 0000:00:10.3 Mar 11 07:44:29 linux kernel: hub 4-0:1.0: USB hub found Mar 11 07:44:29 linux kernel: hub 4-0:1.0: 2 ports detected Mar 11 07:44:29 linux kernel: usb 1-2: new full speed USB device using address 3 Mar 11 07:44:29 linux kernel: usb 1-2: Product: USB ISDN-Connector Mar 11 07:44:29 linux kernel: usb 1-2: Manufacturer: AVM Berlin Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 3 (level, low) -> IRQ 3 Mar 11 07:44:29 linux kernel: ehci_hcd 0000:00:10.4: EHCI Host Controller Mar 11 07:44:29 linux kernel: ehci_hcd 0000:00:10.4: irq 3, pci mem e1272000 Mar 11 07:44:29 linux kernel: ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 Mar 11 07:44:29 linux kernel: ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 Mar 11 07:44:29 linux kernel: usb usb5: Product: EHCI Host Controller Mar 11 07:44:29 linux kernel: usb usb5: Manufacturer: Linux 2.6.8-24.11-default ehci_hcd Mar 11 07:44:29 linux kernel: usb usb5: SerialNumber: 0000:00:10.4 Mar 11 07:44:29 linux kernel: hub 5-0:1.0: USB hub found Mar 11 07:44:29 linux kernel: hub 5-0:1.0: 8 ports detected Mar 11 07:44:29 linux kernel: usb 1-1: USB disconnect, address 2 Mar 11 07:44:29 linux kernel: usb 1-2: USB disconnect, address 3 Mar 11 07:44:29 linux kernel: CAPI Subsystem Rev 1.1.2.8 Mar 11 07:44:29 linux kernel: capifs: Rev 1.1.2.3 Mar 11 07:44:29 linux kernel: capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) Mar 11 07:44:29 linux kernel: CSLIP: code copyright 1989 Regents of the University of California Mar 11 07:44:29 linux kernel: ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded Mar 11 07:44:29 linux kernel: capidrv: Rev 1.1.2.2: loaded Mar 11 07:44:29 linux kernel: module fxusb_CZ unsupported by SUSE/Novell, tainting kernel. Mar 11 07:44:29 linux kernel: fxusb_CZ: module license 'Proprietary' taints kernel. Mar 11 07:44:29 linux kernel: fxusb_CZ: OEM FRITZ!X USB driver, revision 0.5.0 Mar 11 07:44:29 linux kernel: fxusb_CZ: (fxusb_CZ built on Jan 14 2005 at 19:48:50) Mar 11 07:44:29 linux kernel: fxusb_CZ: Loading... Mar 11 07:44:29 linux kernel: usbcore: registered new driver fxusb_CZ Mar 11 07:44:29 linux kernel: fxusb_CZ: Loaded. Mar 11 07:44:29 linux kernel: usb 5-3: new high speed USB device using address 4 Mar 11 07:44:29 linux kernel: hdc: ATAPI 48X DVD-ROM drive, 512kB Cache Mar 11 07:44:29 linux kernel: Uniform CD-ROM driver Revision: 3.20 Mar 11 07:44:29 linux kernel: hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache Mar 11 07:44:29 linux kernel: st: Version 20040403, fixed bufsize 32768, s/g segs 256 Mar 11 07:44:29 linux kernel: usb 1-1: new full speed USB device using address 4 Mar 11 07:44:29 linux kernel: usb 1-1: Product: EPSON Scanner Mar 11 07:44:29 linux kernel: usb 1-1: Manufacturer: EPSON Mar 11 07:44:29 linux kernel: usb 1-2: new full speed USB device using address 5 Mar 11 07:44:29 linux kernel: usb 1-2: Product: USB ISDN-Connector Mar 11 07:44:29 linux kernel: usb 1-2: Manufacturer: AVM Berlin Mar 11 07:44:29 linux kernel: fxusb: WARNG: Driver and stack name do not match! Mar 11 07:44:29 linux kernel: fxusb: Driver 'fxusb_CZ' attached to stack. (152) Mar 11 07:44:29 linux kernel: fxusb_CZ: Stack version 3.11-04 Mar 11 07:44:29 linux kernel: kcapi: Controller 1: fxusb_CZ-0005 attached Mar 11 07:44:29 linux kernel: kcapi: card 1 "fxusb_CZ-0005" ready. Mar 11 07:44:29 linux kernel: capidrv: controller 1 up Mar 11 07:44:29 linux kernel: capidrv-1: now up (2 B channels) Mar 11 07:44:29 linux kernel: capidrv-1: D2 trace enabled Mar 11 07:44:29 linux kernel: usb 2-2: new full speed USB device using address 3 Mar 11 07:44:29 linux kernel: usb 2-2: Product: Standard USB Hub Mar 11 07:44:29 linux kernel: hub 2-2:1.0: USB hub found Mar 11 07:44:29 linux kernel: hub 2-2:1.0: 4 ports detected Mar 11 07:44:29 linux kernel: usb 2-2.3: new full speed USB device using address 4 Mar 11 07:44:29 linux kernel: usb 2-2.3: not running at top speed; connect to a high speed hub Mar 11 07:44:29 linux kernel: usb 2-2.3: Product: USB 2 Flash Media Device Mar 11 07:44:29 linux kernel: usb 2-2.3: Manufacturer: SMSC Mar 11 07:44:29 linux kernel: usb 2-2.3: SerialNumber: 777777777777 Mar 11 07:44:29 linux kernel: Initializing USB Mass Storage driver... Mar 11 07:44:29 linux kernel: scsi2 : SCSI emulation for USB Mass Storage devices Mar 11 07:44:29 linux kernel: Vendor: SMSC Model: USB 2 HS-CF Rev: 2.16 Mar 11 07:44:29 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Mar 11 07:44:29 linux kernel: Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0 Mar 11 07:44:29 linux kernel: Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0 Mar 11 07:44:29 linux kernel: Vendor: SMSC Model: USB 2 HS-MS Rev: 2.16 Mar 11 07:44:29 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Mar 11 07:44:29 linux kernel: Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 1 Mar 11 07:44:29 linux kernel: Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 1, type 0 Mar 11 07:44:29 linux kernel: Vendor: SMSC Model: USB 2 HS-SM Rev: 2.16 Mar 11 07:44:29 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Mar 11 07:44:29 linux kernel: Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 2 Mar 11 07:44:29 linux kernel: Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 2, type 0 Mar 11 07:44:29 linux kernel: Vendor: SMSC Model: USB 2 HS-SD/MMC Rev: 2.16 Mar 11 07:44:29 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Mar 11 07:44:29 linux kernel: BIOS EDD facility v0.16 2004-Jun-25, 2 devices found Mar 11 07:44:29 linux kernel: Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 3 Mar 11 07:44:29 linux kernel: Attached scsi generic sg3 at scsi2, channel 0, id 0, lun 3, type 0 Mar 11 07:44:29 linux kernel: USB Mass Storage device found at 4 Mar 11 07:44:29 linux kernel: usbcore: registered new driver usb-storage Mar 11 07:44:29 linux kernel: USB Mass Storage support registered. Mar 11 07:44:29 linux kernel: Device not ready. Make sure there is a disc in the drive. Mar 11 07:44:29 linux last message repeated 7 times Mar 11 07:44:29 linux kernel: b1: revision 1.1.2.2 Mar 11 07:44:29 linux kernel: b1dma: revision 1.1.2.3 Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 11 (level, low) -> IRQ 11 Mar 11 07:44:29 linux kernel: b1pci: PCI BIOS reports AVM-B1 at i/o 0xd400, irq 11 Mar 11 07:44:29 linux kernel: kcapi: Controller 2: b1pci-d400 attached Mar 11 07:44:29 linux kernel: b1pci: AVM B1 PCI at i/o 0xd400, irq 11, revision 2 Mar 11 07:44:29 linux kernel: b1pci: revision 1.1.2.2 Mar 11 07:44:29 linux kernel: b1pci-d400: card 2 "B1" ready. Mar 11 07:44:29 linux kernel: b1pci-d400: card 2 Protocol: DSS1 Mar 11 07:44:29 linux kernel: b1pci-d400: card 2 Linetype: point to multipoint Mar 11 07:44:29 linux kernel: b1pci-d400: B1-card (3.10-02) now active Mar 11 07:44:29 linux kernel: kcapi: card 2 "b1pci-d400" ready. Mar 11 07:44:29 linux kernel: capidrv: controller 2 up Mar 11 07:44:29 linux kernel: capidrv-2: now up (2 B channels) Mar 11 07:44:29 linux kernel: capidrv-2: D2 trace enabled Mar 11 07:44:29 linux kernel: NET: Registered protocol family 10 Mar 11 07:44:29 linux kernel: Disabled Privacy Extensions on device c037f760(lo) Mar 11 07:44:29 linux kernel: IPv6 over IPv4 tunneling driver Mar 11 07:44:29 linux kernel: ip6_tables: (C) 2000-2002 Netfilter core team Mar 11 07:44:29 linux kernel: ip_tables: (C) 2000-2002 Netfilter core team Mar 11 07:44:29 linux kernel: ip_conntrack version 2.1 (4095 buckets, 32760 max) - 336 bytes per conntrack Mar 11 07:44:29 linux kernel: Disabled Privacy Extensions on device ddaed800(sit0) Mar 11 07:44:29 linux kernel: ip6_conntrack version 0.1 (4095 buckets, 32760 max) - 208 bytes per conntrack Mar 11 07:44:29 linux kernel: Device not ready. Make sure there is a disc in the drive. Mar 11 07:44:29 linux kernel: Device not ready. Make sure there is a disc in the drive. Mar 11 07:44:29 linux kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 Mar 11 07:44:29 linux kernel: NET: Registered protocol family 17 Mar 11 07:44:29 linux kernel: Device not ready. Make sure there is a disc in the drive. Mar 11 07:44:29 linux last message repeated 5 times Mar 11 07:44:29 linux kernel: eth0: no IPv6 routers present Mar 11 07:44:29 linux kernel: PPP generic driver version 2.4.2 Mar 11 07:44:29 linux kernel: ACPI: Power Button (FF) [PWRF] Mar 11 07:44:29 linux kernel: ACPI: Processor [CPU0] (supports C1) Mar 11 07:44:29 linux kernel: ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 10 (level, low) -> IRQ 10 Mar 11 07:44:30 linux rcpowersaved: acpid already running, please set this service to off. The acpid should be started by the powersaved Mar 11 07:44:30 linux kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] Mar 11 07:44:30 linux kernel: parport0: irq 7 detected Mar 11 07:44:30 linux kernel: lp0: using parport0 (polling). Mar 11 07:44:30 linux kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic Mar 11 07:44:30 linux kernel: usbcore: registered new driver usbserial_generic Mar 11 07:44:30 linux kernel: usbcore: registered new driver usbserial Mar 11 07:44:30 linux kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 Mar 11 07:44:37 linux kernel: Linux video capture interface: v1.00 Mar 11 07:44:37 linux kernel: saa7130/34: v4l2 driver version 0.2.12 loaded Mar 11 07:44:37 linux kernel: ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 3 (level, low) -> IRQ 3 Mar 11 07:44:37 linux kernel: saa7130[0]: found at 0000:00:13.0, rev: 1, irq: 3, latency: 32, mmio: 0xf0800000 Mar 11 07:44:37 linux kernel: saa7130[0]: subsystem: 153b:1152, board: Terratec Cinergy 200 TV [card=38,autodetected] Mar 11 07:44:37 linux kernel: saa7130[0]: board init: gpio is 10000 Mar 11 07:44:37 linux kernel: saa7130[0]: i2c eeprom 00: 3b 15 52 11 ff ff ff ff ff ff ff ff ff ff ff ff Mar 11 07:44:37 linux kernel: saa7130[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Mar 11 07:44:37 linux kernel: saa7130[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Mar 11 07:44:37 linux kernel: saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Mar 11 07:44:37 linux kernel: tuner: Ignoring new-style parameters in presence of obsolete ones Mar 11 07:44:37 linux kernel: tuner: chip found at addr 0xc0 i2c-bus saa7130[0] Mar 11 07:44:37 linux kernel: tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by saa7130[0] Mar 11 07:44:37 linux kernel: saa7130[0]: registered device video0 [v4l2] Mar 11 07:44:37 linux kernel: saa7130[0]: registered device vbi0 Mar 11 07:44:39 linux kernel: Non-volatile memory driver v1.2 Mar 11 07:44:42 linux kernel: Device not ready. Make sure there is a disc in the drive. Mar 11 07:44:42 linux last message repeated 7 times Mar 11 07:45:02 linux /usr/sbin/cron[7659]: (CRON) STARTUP (V5.0) Mar 11 07:45:06 linux SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Mar 11 07:45:07 linux pppd[6530]: Starting link Mar 11 07:45:08 linux pppd[6530]: PPP session is 5450 Mar 11 07:45:08 linux kernel: NET: Registered protocol family 24 Mar 11 07:45:08 linux pppd[6530]: Connect: dsl0 <--> eth0 Mar 11 07:45:08 linux pppd[6530]: Couldn't increase MTU to 1500 Mar 11 07:45:08 linux pppd[6530]: Couldn't increase MRU to 1500 Mar 11 07:45:08 linux pppd[6530]: PAP authentication succeeded Mar 11 07:45:08 linux pppd[6530]: peer from calling number 00:90:1A:10:16:21 authorized Mar 11 07:45:08 linux pppd[6530]: Local IP address changed to 217.232.161.86 Mar 11 07:45:08 linux pppd[6530]: Remote IP address changed to 217.5.98.173 Mar 11 07:45:08 linux modify_resolvconf: Service pppd modified /etc/resolv.conf. See info block in this file Mar 11 07:45:10 linux ip-up: SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Mar 11 07:45:10 linux SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Mar 11 07:45:16 linux poll.tcpip: 1 message for fahnenju11@tiscali.de at pop.tiscali.de. Mar 11 07:45:17 linux poll.tcpip: reading message fahnenju11@tiscali.de@pop.tiscali.de:1 of 1 (1025 header octets) (61767 body octets) ............................................................. flushed Mar 11 07:48:38 linux kdm: :0[7356]: pam_unix2: session started for user fahnenju, service xdm Mar 11 07:48:59 linux kernel: Bluetooth: Core ver 2.6 Mar 11 07:48:59 linux kernel: NET: Registered protocol family 31 Mar 11 07:48:59 linux kernel: Bluetooth: HCI device and connection manager initialized Mar 11 07:48:59 linux kernel: Bluetooth: HCI socket layer initialized Mar 11 07:49:05 linux gconfd (fahnenju-8649): (Version 2.6.1) wird gestartet, Prozesskennung 8649, Benutzer »fahnenju« Mar 11 07:49:05 linux gconfd (fahnenju-8649): Die Adresse »xml:readonly:/etc/opt/gnome/gconf/gconf.xml.mandatory« wurde an der Position 0 zu einer nur lesbaren Konfigurationsquelle aufgelöst Mar 11 07:49:05 linux gconfd (fahnenju-8649): Die Adresse »xml:readwrite:/home/fahnenju/.gconf« wurde an der Position 1 zu einer schreibbaren Konfigurationsquelle aufgelöst Mar 11 07:49:05 linux gconfd (fahnenju-8649): Die Adresse »xml:readonly:/etc/opt/gnome/gconf/gconf.xml.defaults« wurde an der Position 2 zu einer nur lesbaren Konfigurationsquelle aufgelöst Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): iid OAFIID:BrokenNoType:20000808 has a NULL type Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): invalid character '#' in iid 'OAFIID:This#!!%$iid%^$%_| ~!OAFIID_ContainsBadChars' Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'name' has no value Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'description' has no value Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'name' has no value Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'description' has no value Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'nautilus:view_as_name' has no value Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'nautilus:view_as_label' has no value Mar 11 07:49:06 linux bonobo-activation-server (fahnenju-8662): Property 'nautilus:viewer_label' has no value Mar 11 07:52:32 linux pppd[6530]: Terminating on signal 15. Mar 11 07:52:37 linux modify_resolvconf: restored /etc/resolv.conf.saved.by.smpppd-ifcfg to /etc/resolv.conf.saved.by.pppd.dsl0 Mar 11 07:52:39 linux modify_resolvconf: Service smpppd-ifcfg modified /etc/resolv.conf. See info block in this file Mar 11 07:52:39 linux pppd[8848]: Plugin rp-pppoe.so loaded. Mar 11 07:52:39 linux pppd[8848]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2 Mar 11 07:52:39 linux pppd[8848]: Plugin passwordfd.so loaded. Mar 11 07:52:39 linux pppd[8848]: pppd 2.4.2 started by root, uid 0 Mar 11 07:52:39 linux pppd[8848]: Renamed interface ppp0 to dsl0 Mar 11 07:52:39 linux pppd[8848]: Using interface dsl0 Mar 11 07:52:39 linux pppd[8848]: Couldn't increase MTU to 1500 Mar 11 07:52:39 linux pppd[8848]: Couldn't increase MRU to 1500 Mar 11 07:52:39 linux pppd[8848]: local IP address 192.168.99.1 Mar 11 07:52:39 linux pppd[8848]: remote IP address 192.168.99.99 Mar 11 07:52:48 linux pppd[8848]: Terminating on signal 15. Mar 11 07:52:48 linux pppd[8848]: Exit. Mar 11 07:52:48 linux modify_resolvconf: restored /etc/resolv.conf.saved.by.smpppd-ifcfg to /etc/resolv.conf Mar 11 07:53:05 linux modify_resolvconf: Service smpppd-ifcfg modified /etc/resolv.conf. See info block in this file Mar 11 07:53:05 linux pppd[9116]: Plugin rp-pppoe.so loaded. Mar 11 07:53:05 linux pppd[9116]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2 Mar 11 07:53:05 linux pppd[9116]: Plugin passwordfd.so loaded. Mar 11 07:53:05 linux pppd[9116]: pppd 2.4.2 started by root, uid 0 Mar 11 07:53:05 linux pppd[9116]: Renamed interface ppp0 to dsl0 Mar 11 07:53:05 linux pppd[9116]: Using interface dsl0 Mar 11 07:53:05 linux pppd[9116]: Couldn't increase MTU to 1500 Mar 11 07:53:05 linux pppd[9116]: Couldn't increase MRU to 1500 Mar 11 07:53:05 linux pppd[9116]: local IP address 192.168.99.1 Mar 11 07:53:05 linux pppd[9116]: remote IP address 192.168.99.99 Mar 11 07:53:08 linux pppd[9116]: Starting link Mar 11 07:53:08 linux pppd[9116]: PPP session is 6241 Mar 11 07:53:08 linux pppd[9116]: Connect: dsl0 <--> eth0 Mar 11 07:53:08 linux pppd[9116]: Couldn't increase MTU to 1500 Mar 11 07:53:08 linux pppd[9116]: Couldn't increase MRU to 1500 Mar 11 07:53:09 linux pppd[9116]: PAP authentication succeeded Mar 11 07:53:09 linux pppd[9116]: peer from calling number 00:90:1A:10:16:21 authorized Mar 11 07:53:09 linux pppd[9116]: Local IP address changed to 217.232.157.165 Mar 11 07:53:09 linux pppd[9116]: Remote IP address changed to 217.5.98.173 Mar 11 07:53:09 linux modify_resolvconf: Service pppd modified /etc/resolv.conf. See info block in this file Mar 11 07:53:10 linux ip-up: SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Mar 11 07:53:10 linux SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Mar 11 07:53:16 linux poll.tcpip: fetchmail: No mail for fahnenju11@tiscali.de at pop.tiscali.de Mar 11 07:53:33 linux kernel: SFW2-INext-ACC-TCP IN=dsl0 OUT= MAC= SRC=62.241.53.16 DST=217.232.157.165 LEN=60 TOS=0x10 PREC=0x00 TTL=55 ID=20677 DF PROTO=TCP SPT=39082 DPT=4660 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A269703DF0000000001030307) Gruß, Jürgen
participants (1)
-
Jürgen Fahnenschreiber