Moin Moin! Ich habe jetzt 2 Realtek-Karten! Es sieht aber noch fast so aus wie vorher: eth0 geht eth1 nicht. Ich schreib euch diesmal gleich ein paar angaben: # ifconfig eth0 Link encap:Ethernet HWaddr 00:30:84:27:56:B0 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:116 errors:0 dropped:0 overruns:0 frame:0 TX packets:150 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:10 Base address:0xf800 eth1 Link encap:Ethernet HWaddr 00:30:84:0D:65:4D inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:5 Base address:0xf400 ippp0 Link encap:Point-to-Point Protocol inet addr:192.168.10.99 P-t-P:192.168.10.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP DYNAMIC MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:30 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:3924 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.10.1 0.0.0.0 255.255.255.255 UH 0 0 0 ippp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo # lsmod Module Size Used by ip_masq_vdolive 1432 0 (unused) ip_masq_user 2664 0 (unused) ip_masq_raudio 3096 0 (unused) ip_masq_quake 1448 0 (unused) ip_masq_portfw 2560 0 (unused) ip_masq_mfw 3368 0 (unused) ip_masq_irc 1624 0 (unused) ip_masq_ftp 2552 0 (unused) ip_masq_cuseeme 1176 0 (unused) ip_masq_autofw 2576 0 (unused) snd-card-opl3sa2 8596 0 isapnp 27384 0 [snd-card-opl3sa2] snd-cs4231 18464 0 [snd-card-opl3sa2] snd-pcm 28824 0 [snd-cs4231] snd-mixer 22704 0 [snd-card-opl3sa2 snd-cs4231] snd-opl3 4328 0 [snd-card-opl3sa2] snd-hwdep 3052 0 [snd-opl3] snd-timer 8064 0 [snd-cs4231 snd-pcm snd-opl3] snd-mpu401-uart 2308 0 [snd-card-opl3sa2] snd-rawmidi 9112 0 [snd-mpu401-uart] snd-seq-device 3392 0 [snd-rawmidi] snd 35596 1 [snd-card-opl3sa2 snd-cs4231 snd-pcm snd-mixer snd-opl3 snd-hwdep snd-timer snd-mpu401-uart snd-rawmidi snd-seq-device] soundcore 2564 3 [snd] rtl8139 12224 2 (autoclean) hisax 483760 3 isdn 117932 4 [hisax] slhc 4440 1 [isdn] memstat 1476 0 (unused) serial 42484 0 (autoclean) So! Yast 2 scheint mit der Sache auc etwas übervordert. Egal welche der beiden Karten ich konfigurieren will, sie hat immer die IP 192.168.0.1 also eth0. Ich hoffe, daß ich jetzt wenigstens die Geschichte zum Laufen bekomme! Gruß Thilo --------------------------------------------------------------------- To unsubscribe, e-mail: suse-linux-unsubscribe@suse.com For additional commands, e-mail: suse-linux-help@suse.com