Hoi z'samme
Tja, ich steh hier leider vor einem Problem das mich rätseln lässt, und ich
wirklich nur eine grobe Beschreibung geben kann:
Ich versuche ein Wacom Graphire 2 am USB unter SuSE 8.0 zum laufen zu bringen,
ich habe schon die verschiedensten Methoden ausprobiert:
Im Kerner 2.4.18-4GB sind die Treiber eigenlich als Modul gebaut, also einfach
mal rein in den Port. In der /var/log/messages sagt er dann:
--------schnipp---------
Jul 3 18:45:49 linux kernel: usb.c: registered new driver wacom
Jul 3 18:45:49 linux kernel: usb-uhci.c: interrupt, status 3, frame# 625
Jul 3 18:45:49 linux kernel: input0: Wacom Graphire2 4x5 on usb1:3.0
Jul 3 18:45:49 linux kernel: wacom.c: v1.21.3 Vojtech Pavlik
Jul 3 18:45:49 linux kernel: wacom.c: USB Wacom Graphire and Wacom Intuos
tablet driver
--------schnapp---------
Geladene Module laut lsmod sind dann wacom, evdev, hid, input und der Rest des
USB gedöns mit usb-uhci
Fohen Mutes ging es dann daran, den XFree 4 zu konfigurieren, mit SaX2. Das
war leider ein völliges Fiasko, danach ging erst mal gar nichts mehr, auch
die normale Maus nicht. Eingetragen in die Schnittstelle war
/dev/input/event0.
Also als nächstes manuell folgende Einträge in die /etc/X11/XF86config
geschrieben:
------------schnipp-------
Section "Module"
Load "type1"
Load "speedo"
Load "extmod"
Load "freetype"
Load "glx"
Load "v4l"
Load "wacom" #Module for Wacom Device driver
EndSection
# Settings for wacom pen
Section "InputDevice"
Identifier "pen1"
Driver "wacom"
Option "Type" "stylus"
Option "Mode" "absolute"
Option "Device" "/dev/input/event0"
Option "USB" "on"
Endsection
# Settings for wacom eraser
Section "InputDevice"
Identifier "eraser1"
Driver "wacom"
Option "Type" "eraser"
Option "Device" "/dev/input/event0"
Option "Mode" "absolute"
Option "USB" "on"
Endsection
# Settings for wacom cursor (mouse)
Section "InputDevice"
Identifier "cursor1"
Driver "wacom"
Option "Type" "cursor"
Option "Mode" "relative"
Option "Device" "/dev/input/event0"
Option "USB" "on"
Endsection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
InputDevice "eraser1" "AlwaysCore"
InputDevice "pen1" "AlwaysCore"
InputDevice "cursor1" "AlwaysCore"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
---------schnapp-----------------
Leider kein response, ebensowenig wenn das Device input0 angegeben ist.
Der Gimp erkennt die InputDevices und gibt sie als Auswahlmöglichkeit an, das
war's dann aber auch. Im Log vom XServer ist nichts spezielles zu erkennen.
Im Wacom Howto habe ich dann den Link auf die Wacom USB MiniHowto gefunden,
und die dortigen Modulquellen kompiliert und eingebunden. Leider immer noch
mit dem gleichen Ergebnis.
Eine Suche bei google brachte auch keine neuen Erkenntnisse, also bin ich so
schlau als auch bevor. Auch ein Test mit dem gpm wie im Wacom Howto
beschrieben, hat keine Resultate gebracht, also gehe ich mal davon aus, das
es mit dem USB HotPlugging zu tun hat, aber wie finde ich hier mehr
Informationen, in der Messages und boot.msg / boot.log sieht alles gut aus.
Noch ein paar Daten zur restlichen USB Konfiguration aus usbview:
------schnipp------------
USB UHCI Root Hub
Serial Number: d400
Speed: 12Mb/s (full)
Number of Ports: 2
Bandwidth allocated: 0 / 900 (0%)
Total number of interrupt requests: 0
Total number of isochronous requests: 0
USB Version: 1.00
Device Class: 09(hub )
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 8
Number of Configurations: 1
Config Number: 1
Number of Interfaces: 1
Attributes: 40
MaxPower Needed: 0mA
Interface Number: 0
Name: hub
Alternate Number: 0
Class: 09(hub )
Sub Class: 0
Protocol: 0
Number of Endpoints: 1
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 8
Interval: 255ms
DeskJet 930C
Manufacturer: Hewlett-Packard
Serial Number: ES0BD191DNJJ
Speed: 12Mb/s (full)
USB Version: 1.00
Device Class: 00(>ifc )
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 8
Number of Configurations: 1
Vendor Id: 03f0
Product Id: 1204
Revision Number: 1.00
Config Number: 1
Number of Interfaces: 1
Attributes: 40
MaxPower Needed: 2mA
Interface Number: 0
Name: usblp
Alternate Number: 0
Class: 07(print)
Sub Class: 1
Protocol: 1
Number of Endpoints: 2
Endpoint Address: 81
Direction: in
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms
Endpoint Address: 02
Direction: out
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms
Interface Number: 0
Name: usblp
Alternate Number: 1
Class: 07(print)
Sub Class: 1
Protocol: 2
Number of Endpoints: 2
Endpoint Address: 01
Direction: out
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms
Endpoint Address: 82
Direction: in
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms
ET-0405A-UV2.0-3
Manufacturer: WACOM
Speed: 1.5Mb/s (low)
USB Version: 1.10
Device Class: 00(>ifc )
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 8
Number of Configurations: 1
Vendor Id: 056a
Product Id: 0011
Revision Number: 2.03
Config Number: 1
Number of Interfaces: 1
Attributes: 80
MaxPower Needed: 40mA
Interface Number: 0
Name: wacom
Alternate Number: 0
Class: 03(HID )
Sub Class: 1
Protocol: 2
Number of Endpoints: 1
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 8
Interval: 10ms
-------------schnapp----------
Der Drucker läuft im übrigen prima.
Das Ganze ist ein auf VIA KT133 aufgesetztes Duron System....
und jetzt ist guter Rat teuer....
Danke für jede Hilfe
Jörn
PS: Das Tablett funktioniert unter WinXP...