Hallo Liste; in 2.6.x gibt es ja zwei Möglichkeiten SIL3112 basierte SATA-Controler zu betreiben: Den siimage-Treiber und den sata_sil-Treiber. Da der siimage_treiber bei mit schlechter läuft als der sata_sil-Treiber, möchte ich den sata_sil-Treiber benutzen. Im Kraxel-2.6.3 ist siimage fest in den Kernel eingebaut (CONFIG_BLK_DEV_SIIMAGE=y) und sata_sil als Module gebaut (CONFIG_SCSI_SATA_SIL=m). Das hat aber zur Folge, das der siimage-Treiber den SIL3112 übernimmt, bevor sata_sil überhaupt geladen werden kann. Versuche, dies mit den Kernelparametern ide4=noprobe ide5=noprobe abzustellen waren nicht von Erfolg gekrönt. Aus boot.msg : [...] <4>Kernel command line: root=/dev/hde2 vga=0x317 desktop hdc=ide-scsi hdclun=0 splash=silent 3 ide4=noprobe ide5=noprobe <6>ide_setup: hdc=ide-scsi <6>ide_setup: hdclun=0 <6>bootsplash: silent mode. <6>ide_setup: ide4=noprobe <6>ide_setup: ide5=noprobe [...] <6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>AMD7411: IDE controller at PCI slot 0000:00:07.1 <6>AMD7411: chipset revision 1 <6>AMD7411: not 100%% native mode: will probe irqs later <6>AMD7411: 0000:00:07.1 (rev 01) UDMA100 controller <6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio <6> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio <4>hda: DM166D DVD-ROM, ATAPI CD/DVD-ROM drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <4>hdc: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive <4>ide1 at 0x170-0x177,0x376 on irq 15 <6>PDC20270: IDE controller at PCI slot 0000:00:09.0 <6>PDC20270: chipset revision 2 <6>PDC20270: 100%% native mode on irq 177 <6> ide2: BM-DMA at 0x1830-0x1837, BIOS settings: hde:pio, hdf:pio <6> ide3: BM-DMA at 0x1838-0x183f, BIOS settings: hdg:pio, hdh:pio <4>hde: SAMSUNG SP0612N, ATA DISK drive <4>ide2 at 0x1868-0x186f,0x1862 on irq 177 <6>SiI3112 Serial ATA: IDE controller at PCI slot 0000:00:0a.0 <6>SiI3112 Serial ATA: chipset revision 2 <6>SiI3112 Serial ATA: 100%% native mode on irq 185 <6> ide4: MMIO-DMA , BIOS settings: hdi:pio, hdj:pio <6> ide5: MMIO-DMA , BIOS settings: hdk:pio, hdl:pio <4>hdi: HDS722516VLSA80, ATA DISK drive <4>ide4 at 0xe1818080-0xe1818087,0xe181808a on irq 185 <4>hdk: no response (status = 0xfe) <4>hdk: no response (status = 0xfe), resetting drive <4>hdk: no response (status = 0xfe) <4>hde: max request size: 1024KiB <6>hde: 117304992 sectors (60060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) <6> hde: hde1 < hde5 hde6 hde7 hde8 hde9 > hde2 hde3 hde4 <4>hdi: max request size: 64KiB <6>hdi: 321672960 sectors (164696 MB) w/7938KiB Cache, CHS=20023/255/63 <6> hdi: hdi1 hdi2 hdi3 hdi4 < hdi5 hdi6 hdi7 hdi8 > [...] Muss ich nun für sata_sil immer einen Kernel aus den Sourcen ( mit CONFIG_BLK_DEV_SIIMAGE=m oder #CONFIG_BLK_DEV_SIIMAGE is not set ) bauen oder gibt es doch eine Möglichkeit sata_sil mit der Kraxel-Konfiguration zu benutzen ?
participants (1)
-
Markus Kossmann