Am Montag, 7. Januar 2008 schrieb Martin Hofius:
Am Montag, 7. Januar 2008 schrieb gooly@gmx.at:
Am Montag, 7. Januar 2008 schrieb Christoph Graulich:
Hallo,
...
es beginnt jetzt etwas zu nerven. Wenn ich den PC einschalte, fährt die Festplatte nicht an, irgendwann nach ein paar mal dann schon, dann ist alles ok! Ich hab schon mal alles gesichert :)
Hab einmal smartctl installiert und diesen Linux-Konsolen-Gesundheitstest absolviert die Platte ohne Befund - hmm, der Betrieb, wenn sie läuft, ist ja auch nicht das Problem.
Bei mir sieht es z.B. so aus:
smartctl - a /dev/hda ... Firmware Version: VC100-30 User Capacity: 200,049,647,616 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a Local Time is: Sun Dec 30 21:24:43 2007 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. ... SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 001 001 025 Pre-fail Always FAILING_NOW 16960 4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3268
ja und was schreibt smartctl bei Dir am Ende: SMART overall-health self-assessment test result: PASSED das sagt mir alles ok - richtig? BTW es ist die einzige Platte in diesem PC (Soltek Qbic 'Bärbaum':) Und die Temperatur mit 32° -35° während diverser smartctl heute sind auch nicht so unheimlich. smartctl selbst schaut so aus: smartctl -a /dev/hda smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG SP2014N Serial Number: S088J10L405519 Firmware Version: VC100-41 User Capacity: 200,049,647,616 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a Local Time is: Mon Jan 7 21:08:22 2008 CET ==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (4622) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 77) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 6912 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1046 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 2549 10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 253 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 532 187 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 65536 190 Unknown_Attribute 0x0022 142 124 000 Old_age Always - 32 194 Temperature_Celsius 0x0022 142 124 000 Old_age Always - 32 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 2357057 196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 253 253 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2542 - SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 SMART Selective self-test log data structure revision number 0 Warning: ATA Specification requires selective self-test log data structure revision number = 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Das finde ich schon sehr deutlich. Wenn bei Dir in Attribut 3 nichts drin steht, könnte es allerdings auch daran liegen, dass der Fehler nur dann gemeldet wird, wenn die Platte auch mit Fehler tatsächlich hochgelaufen ist. Wenn sie entweder ohne Probleme oder gar nicht hochläuft, dann wird es schwer. Aber was ist mit den Werten "Value" und "worst"? Liegen die beide noch über 25 (Thresh)? ...
-- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org