Hallo, SuSE 10.1 Ich habe einen USB-Stick der sehr gut funktioniert. Leider funktioniert ein anderes Gerät überhaupt nicht. Ich habe das Gerät unter FreeBSD problemlos zum laufen bekommen. Woran kann das liegen? Hier ein Auszug aus der /var/log/messages beim ein und ausstecken der beiden Geräte (das, welches funktioniert, und das, welches nicht funktioniert): ohci_hcd 0000:00:02.3: OHCI Host Controller ohci_hcd 0000:00:02.3: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.3: irq 193, io mem 0xef000000 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.16.13-4-default ohci_hcd usb usb2: SerialNumber: 0000:00:02.3 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usb 1-1: new full speed USB device using ohci_hcd and address 2 usb 1-1: new device found, idVendor=10d6, idProduct=1100 usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=2 usb 1-1: Product: USB MASS STORAGE CLASS usb 1-1: SerialNumber: USB MASS STORAGE CLASS usb 1-1: configuration #1 chosen from 1 choice SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. Vendor: Model: Rev: Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete Driver 'sd' needs updating - please use bus_type methods SCSI device sda: 2000609 512-byte hdwr sectors (1024 MB) sda: Write Protect is off sda: Mode Sense: 00 c0 00 00 sda: assuming drive cache: write through SCSI device sda: 2000609 512-byte hdwr sectors (1024 MB) sda: Write Protect is off sda: Mode Sense: 00 c0 00 00 sda: assuming drive cache: write through sda: unknown partition table sd 0:0:0:0: Attached scsi removable disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 usb 1-2: new full speed USB device using ohci_hcd and address 3 usb 1-2: new device found, idVendor=0421, idProduct=045b usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-2: Product: Nokia 6280 usb 1-2: Manufacturer: Nokia usb 1-2: SerialNumber: 353949013107215 usb 1-2: configuration #1 chosen from 1 choice scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning Vendor: Nokia Model: Nokia 6280 Rev: 0000 Type: Direct-Access ANSI SCSI revision: 04 SCSI device sdb: 124161 512-byte hdwr sectors (64 MB) sdb: test WP failed, assume Write Enabled sdb: assuming drive cache: write through SCSI device sdb: 124161 512-byte hdwr sectors (64 MB) sdb: test WP failed, assume Write Enabled sdb: assuming drive cache: write through sdb: sd 1:0:0:0: Attached scsi removable disk sdb sd 1:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete sdb: Current: sense key: No Sense Additional sense: No additional sense information agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Loading R200 Microcode Was kann ich dagegen unternehmen? Danke Karl -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org