Hi, Am 06.10.2003 15:49 schrieb Gerald Martin:
Hallo Liste Ich bin dabei, einen FAXServer mit HylaFAx in Gang zu setzten, bin doch bisher leider erfolglos: --> Das Modem nimmt nicht ab in der /var/spool/fax/etc/config.ttyS1 hab ich nach der erschöpfednen Rechereche in Foren/Listen/etc. zig verschiedene Möglichkeiten probiert, bisher ohne Erfolg. 'RingsBeforeAnswer' steht auf 2 Der Server läuft mit SuSE 8.1; das Modem funzt an sich schon (dh. z.B. mit kinternet). Gibt es ein Testprogramm, mit welchem man sieht, wie das Modem auf welche Abfragen reagiert? Ich bin mir nicht sicher, ob es an den Configs von HylaFAX liegt, oder ob das Problem woanders liegt.
Es liegt wohl an HylaFAX, ansonsten kannst du mit minicom testen.
In einem Tutorial stand, daß ELSA zu Lebzeiten eine Config für das Modem zur Verfügung gestellt hat. Leider ist hab ich diese bisher nicht finden können, auch nicht auf den Mirrors von ELSA.
Diese Konfig hat bei mir funktioniert. Falls es bei Dir nicht funktioniert, probiere mal das Modem als Class 1.0 zu betreiben. Tel.Nr anpassen nicht vergessen. # # Class 2.0 modem configuration for ELSA Modems with V.250 command # set. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 49 AreaCode: 202 FAXNumber: +49.202.xxxxxxxx LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 527 SessionTracing: 527 RecvFileMode: 0644 LogFileMode: 0600 DeviceMode: 0666 RingsBeforeAnswer: 2 SpeakerVolume: on GettyArgs: "-r -b -s %s %l" LocalIdentifier: "master of desaster" LogFacility: local7 TagLineFont: etc/lutRS18.pcf TagLineFormat: "Von %%l|%c|Seite %%p von %%t" PercentGoodLines: 95 MaxConsecutiveBadLines: 5 MaxRecvPages: 250 ModemPriority: 200 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2.0 # use this to supply a hint ModemRate: 38400 # max rate for DCE-DTE communication #ModemRate: 115200 # max rate for DCE-DTE communication ModemFlowControl: rtscts # XON/XOFF flow control assumed ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # test ModemSetupAACmd: AT+FAA=1 # enable in current class # # We normally append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT0W%s # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # ModemResetCmds: ATX3 # stuff to do when modem is reset ModemAnswerCmd: ATA # use this to answer phone ModemNoFlowCmd: AT+IFC=0,0; ModemHardFlowCmd: AT+IFC=2,2; ModemSoftFlowCmd: AT+IFC=1,1; ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer ModemWaitForConnect: Yes # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # # Configuration parameters for Class 2.0 modems. # #Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0 #Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct) #Class2CQCmd: "" # commands to enable copy quality proc. #Class2AbortCmd: AT+FKS # abort session command #Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities #Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities #Class2TBCCmd: AT+FPP=0 # setup stream mode #Class2CRCmd: AT+FCR=1 # enable capability to receive #Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter #Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing #Class2LIDCmd: AT+FLI # set local identifier command #Class2DCCCmd: AT+FCC # set modem capabilities command #Class2DISCmd: AT+FIS # set session parameters command #Class2DDISCmd: "" # disable pre-dial DIS command hack #Class2CIGCmd: AT+FPI # set polling identifier command #Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command #Class2PIECmd: AT+FIE=0 # disable interrupt-enable command #Class2PTSCmd: AT+FPS # set post-page status command #Class2SPLCmd: AT+FSP # set polling indicator command #Class2NFLOCmd: AT+FLO=0 # set no flow control command #Class2SFLOCmd: AT+FLO=1 # set software flow control command #Class2HFLOCmd: AT+FLO=2 # set hardware flow control ommand # My owns #Class2APCmd: AT+FAP # string #Class2APQueryCmd: AT+FAP=? # string -Joerg