Hallo! Ich habe jetzt endlich Zugriff aufs System bekommen und kann somit ein paar Ergebnisse liefern: gdi1:~ # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: SAF-TE Rev: 1127 Type: Processor ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 05 Lun: 00 Vendor: HP Model: C5713A Rev: H107 Type: Sequential-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 05 Lun: 01 Vendor: HP Model: C5713A Rev: H107 Type: Medium Changer ANSI SCSI revision: 02 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: MegaRAID Model: LD 0 RAID5 52G Rev: H Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 02 Lun: 00 Vendor: BNCHMARK Model: DLT1 Rev: 5032 Type: Sequential-Access ANSI SCSI revision: 02 gdi1:~ # mtx -f /dev/sg2 status mtx: Request Sense: Error Code=0 (Unknown?!) mtx: Request Sense: Sense Key=No Sense mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 00 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: BPV=no mtx: Request Sense: Error in CDB=no mtx: Request Sense: SKSV=no READ ELEMENT STATUS Command Failed gdi1:~ # mtx -f /dev/sg1 status mtx: Request Sense: Long Report=yes mtx: Request Sense: Valid Residual=no mtx: Request Sense: Error Code=0 (Unknown?!) mtx: Request Sense: Sense Key=No Sense mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 00 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: BPV=no mtx: Request Sense: Error in CDB=no mtx: Request Sense: SKSV=no READ ELEMENT STATUS Command Failed gdi1:~ # mtx -f /dev/sg0 status mtx: Request Sense: Long Report=yes mtx: Request Sense: Valid Residual=no mtx: Request Sense: Error Code=0 (Unknown?!) mtx: Request Sense: Sense Key=No Sense mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 00 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: BPV=no mtx: Request Sense: Error in CDB=no mtx: Request Sense: SKSV=no READ ELEMENT STATUS Command Failed gdi1~ # tapeinfo -f /dev/sg0 Product Type: Processor Vendor ID: 'HP ' Product ID: 'SAF-TE^@^@^@^@^@^@^@^@^@^@' Revision: '1127' Attached Changer: No SerialNumber: '[^@' MinBlock:23296 MaxBlock:514 SCSI ID: 4 SCSI LUN: 0 Ready: yes Medium Type: Not Loaded Density Code: 0x5b BlockSize: 5251104 DataCompEnabled: no DataCompCapable: no DataDeCompEnabled: no CompType: 0x70431440 DeCompType: 0x0 Block Position: 1526726656 kann als /dev/st1 angesprochen werden. gdi1~ # tapeinfo -f /dev/sg1 Product Type: Tape Drive Vendor ID: 'HP ' Product ID: 'C5713A ' Revision: 'H107' Attached Changer: No MinBlock:1 MaxBlock:16777215 SCSI ID: 5 SCSI LUN: 0 Ready: yes BufferedMode: yes Medium Type: Not Loaded Density Code: 0x26 BlockSize: 0 DataCompEnabled: yes DataCompCapable: yes DataDeCompEnabled: yes CompType: 0x20 DeCompType: 0x0 Block Position: 637534208 gdi1~ # tapeinfo -f /dev/sg2 Product Type: Medium Changer Vendor ID: 'HP ' Product ID: 'C5713A ' Revision: 'H107' Attached Changer: No MinBlock:1 MaxBlock:320 SCSI ID: 5 SCSI LUN: 1 Ready: yes BufferedMode: yes Medium Type: Not Loaded Density Code: 0x26 BlockSize: 0 DataCompEnabled: yes DataCompCapable: yes DataDeCompEnabled: yes CompType: 0x20 DeCompType: 0x0 Block Position: 637534208 gdi1:~ # mtx -f /dev/sg0 load 2 mtx: Request Sense: Long Report=yes mtx: Request Sense: Valid Residual=no mtx: Request Sense: Error Code=0 (Unknown?!) mtx: Request Sense: Sense Key=No Sense mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 00 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: BPV=no mtx: Request Sense: Error in CDB=no mtx: Request Sense: SKSV=no READ ELEMENT STATUS Command Failed Kernel 2.4.18-64GB-SMP Ich hoffe, ihr könnt damit was anfangen. Normalerweise sollte ein mtx -f /dev/sg0 load 2 ja eigentlich funktionieren (ich hab das auch noch mit " ... -f /dev/sg1 ... und ... /dev/sg2 ... " probiert. Immer wieder das o.s. Ergebnis. Vielen Dank schonmal und ein schönes Wochenende noch. ciao, Stefan