Hallo Johannes, danke erstmal für die Tipps. Entschuldige bitte, dass ich erst jetzt dazu komme es auszuprobieren:
Der Canon Lide20 braucht den "plustek" Treiber,
Done.
der CanoScan 2700F den "canon" Treiber.
Done
Letzteren in /etc/sane.d/dll.conf aktivieren
Done => /etc/sane.d/canon.conf /dev/sg2
insserv sane-dev; rcsane-dev start" (macht ggf. YaST
done
gelesen
http://lists.alioth.debian.org/pipermail/sane-devel/2006-May/016922.h tml
Gelesen.
Generell siehe http://de.opensuse.org/SDB:Scanner_einrichten_ab_SUSE_LINUX_9.2
hm, gelesen. Hier die Meldungen, die ich beim einrichten erhielt. ... standalone:/home/boris # insserv sane-dev standalone:/home/boris # rcsane-dev start done ...... standalone:/home/boris # sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. found SCSI scanner "CANON IX-27015C 1.15" at /dev/sg2 # Your SCSI scanner was detected. It may or may not be supported by SANE. Try # scanimage -L and read the backend's manpage. found USB scanner (vendor=0x04a9 [Canon], product=0x220d [CanoScan], chip=LM9832/3) at libusb:004:003 # Your USB scanner was (probably) detected. It may or may not be supported by # SANE. Try scanimage -L and read the backend's manpage. # Not checking for parallel port scanners. # Most Scanners connected to the parallel port or other proprietary ports # can't be detected by this program. ...... standalone:/home/boris # scanimage -L device `plustek:libusb:004:003' is a Canon N670U/N676U/LiDE20 USB flatbed scanner .... standalone:/home/boris # scanimage -d canon:/dev/sg2 -T && echo OK || echo FAILED scanimage: open of device canon:/dev/sg2 failed: Error during device I/O FAILED Habe ich was falsch geschrieben? aus messages: Aug 6 12:17:40 standalone kernel: scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 Aug 6 12:17:40 standalone kernel: <Adaptec 2940 SCSI adapter> Aug 6 12:17:40 standalone kernel: aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs Aug 6 12:17:40 standalone kernel: Aug 6 12:17:40 standalone kernel: usb 2-1: new full speed USB device using ohci_hcd and address 2 Aug 6 12:17:40 standalone kernel: usb 4-1: new full speed USB device using ohci_hcd and address 2 Aug 6 12:17:40 standalone kernel: hub 4-1:1.0: USB hub found Aug 6 12:17:40 standalone kernel: hub 4-1:1.0: 4 ports detected Aug 6 12:17:40 standalone kernel: usb 4-1.4: new full speed USB device using ohci_hcd and address 3 Aug 6 12:17:40 standalone kernel: drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04E8 pid 0x3008 Aug 6 12:17:40 standalone kernel: usbcore: registered new driver usblp Aug 6 12:17:40 standalone kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Aug 6 12:17:40 standalone kernel: bootsplash: status on console 0 changed to on Aug 6 12:17:40 standalone kernel: NET: Registered protocol family 17 Aug 6 12:17:40 standalone kernel: BIOS EDD facility v0.16 2004-Jun-25, 3 devices found Aug 6 12:17:40 standalone kernel: NET: Registered protocol family 10 Aug 6 12:17:40 standalone kernel: Disabled Privacy Extensions on device c036b920(lo) Aug 6 12:17:40 standalone kernel: IPv6 over IPv4 tunneling driver Aug 6 12:17:40 standalone kernel: eth0: Media Link On 100mbps full-duplex Aug 6 12:17:40 standalone kernel: Vendor: CANON Model: IX-27015C Rev: 1.15 Aug 6 12:17:40 standalone kernel: Type: Scanner ANSI SCSI revision: 02 Aug 6 12:17:40 standalone kernel: target2:0:1: Beginning Domain Validation Aug 6 12:17:40 standalone kernel: target2:0:1: Domain Validation skipping write tests Aug 6 12:17:40 standalone kernel: target2:0:1: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) Aug 6 12:17:40 standalone kernel: target2:0:1: Ending Domain Validation Aug 6 12:17:40 standalone kernel: Attached scsi generic sg2 at scsi2, channel 0, id 1, lun 0, type 6 Fakt ist jetzt leider, dass ich mit dem Teil nicht scannen kann. System: Suse 10.0 -- CU at the trails. Es lebe mein tripple triangle.