Als Modem benutze ich ein Creatix SG144 (14.4 KBit) Dieses Modem meldet sich mit Hab auch ein Creatix SG144 (14.4 KBit) beim laufen. Kann sowohl faxe Senden und Empfangen. Nur beim senden gibt es bei manchen Faxgeräten das Problem, dass nach der ersten Seite von der Gegenstelle der korrekte Empfang nicht bestätigt wird, und daher die Seite immer wieder gesendet wird.
Dec 29 11:38:28.34: [25177]: SENT 30792 bytes of data Dec 29 11:38:28.34: [25177]: SEND 1D RTC Dec 29 11:38:28.34: [25177]: <-- data [9] Dec 29 11:38:28.34: [25177]: SEND end page Dec 29 11:38:28.34: [25177]: SEND send MPS (more pages, same document) Dec 29 11:38:28.34: [25177]: <-- data [2] Dec 29 11:38:44.40: [25177]: --> [5:ERROR] Dec 29 11:38:44.40: [25177]: SEND recv RTN (retrain negative) Sonst arbeitet allse gut. Als Anhang meine config und config.ttyS0 p.s. Der Phase B error wird glaub ich in der Support-Datenbank besprochen (Siehe unter Rockwell) mit freundliche Grüßen Klaus Engelhardt, Inst. Prof. Dr. E. Neuburger & Partner GmbH Tel.: +4989 15812041 Fax : +4989 15812012 <A HREF="mailto:engelhardt@neuburger.com">mailto:engelhardt@neuburger.com</A> (geschäftlich) <A HREF="mailto:Klaus_Engelhardt@gmx.de">mailto:Klaus_Engelhardt@gmx.de</A> (privat) </PRE> <PRE> LogFacility: daemon CountryCode: 49 AreaCode: 89 LongDistancePrefix: 0 InternationalPrefix: 0 DialStringRules: etc/dialrules ServerTracing: 34319 ContCoverPage: etc/cover.templ MaxSendPages: 1000 ModemClass: "any:.*" SessionTracing: 34319 Use2D-: No </PRE> <PRE> # $Id: rc32acl,v 1.17 1996/06/24 02:58:39 sam Rel $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Configuration for a Rockwell RC32ACL-based Class 2 modem. # Boca M1440E firmware V1.000 # SupraFAX v.32bis firmware V1.000 # (and others) # # This configuration file sets up the modem to run at 38.4 for # sending and for receiving. RTS/CTS is used for flow control # which also works for data connections. Adaptive answer support # is reliable, but to use it you must also enable ModemWaitForConnect # to force the server to skip intermediate status messages and # wait for the "CONNECT" message. # # CountryCode: 49 AreaCode: 89 FAXNumber: +49.89.158xxxxx LongDistancePrefix: 0 InternationalPrefix: 0 DialStringRules: etc/dialrules ServerTracing: 324319 SessionTracing: 324319 RecvFileMode: 0666 LogFileMode: 0600 DeviceMode: 0644 RingsBeforeAnswer: 1 SpeakerVolume: Medium GettyArgs: "-h %l dx_" LocalIdentifier: "Neuburger + Partner" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %l| NoCarrierRetrys: 3 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2 # use class 2 interface ModemRate: 19200 ModemFlowControl: rtscts # default ModemWaitForConnect: yes # wait for CONNECT on answer # ModemResetCmds: AT&F#CID=1 # what you want for a Supra ModemNoFlowCmd: AT&K0 # disable flow control cmd ModemHardFlowCmd: AT&K3 # hardware flow control cmd ModemSoftFlowCmd: AT&K4 # software flow control cmd ModemSetupDTRCmd: AT&D2 # DTR off causes modem to reset ModemSetupDCDCmd: AT&C1 # DCD follows carrier ModemSetupAACmd: AT+FCLASS=0;+FAA=1 # enable in class 0 # ModemSendFillOrder: LSB2MSB # as expected ModemRecvFillOrder: MSB2LSB # opposite of what makes sense Class2RecvDataTrigger: "\022" # a la 2388-B